Planet Networking & Communication POE-173 User Manual

1. Package Contents
Thank you for purchasing PLANET Single-Port
10/100/1000Mbps Ultra PoE Injectors, POE-172 and
POE-173.
Model LAN Port Speed PoE Standard
Budget
Ultra PoE, backward
60
POE-172 10/100/1000Mbps compatible with IEEE
watts
802.3at/af standard
60
POE-173 10/100/1000Mbps Ultra PoE
watts
The term "Ultra PoE Injector" in the following section
of this User's Manual means the POE-172 and POE-173.
The box of the Single-Port 10/100/1000Mbps Ultra PoE
Injector should contain the following items:
 The Single-Port 10/100/1000Mbps Ultra PoE Injector
x 1
 User's Manual x 1
 AC Power Cord x 1
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
- 1 -
2. Product Features
„ Interface
 2 x RJ45 interface
 1-port Data + Power output
 1-port Data input
 1 x AC 100-240V input power socket
„ Power over Ethernet
 Ultra Power over Ethernet PSE
 Up to 60 watts of power on 4-pair UTP cable
 Backward compatible with IEEE 802.3at/af PD
device (POE-172)
 Auto-detection of PoE IEEE 802.3at/af equipment
and devices to check whether there's any damage
done via incorrect installation (POE-172)
 Remote power feeding up to 100m
„ Hardware
 All-in-one compact size design
 Internal power supply
 LED indicators for Power LED and Active LED (PoE
ready/in-use)
- 2 -
PSE (Power Sourcing Equipment) is a
device (switch, or hub for instance) that
will provide power in a PoE setup. The
maximum allowed continuous output power
Note
per such device in IEEE 802.3af is 15.4
watts, in IEEE 802.3at is 30 watts and ultra
PoE is 60 watts
PoE
PD (Powered Device) such as an IP
phone, network camera or wireless access
point is a PoE-enabled terminal by PSE and
Note
thus it consumes energy.
3. Product Specifications
Product POE-172
Hardware Specifications
LAN 1 x RJ45 STP, "Data" Input Port
1 x RJ45 STP, "Data + Power"
PoE
Output Port
Interface
1 x AC input power socket,
AC Connector
IEC-320 C6
Ultra PoE 4-pair UTP Cat. 5, 5e, 6 up to
(60W) 100m (328ft)
Network
802.3af/
Cable
2-pair UTP Cat. 3, 4, 5, up to
at PoE
100m (328ft)
(15W/30W)
- 3 -
System: Power x 1 (Green)
LED Indicator PoE Port: Active, PoE ready/
Data Rate 10/100/1000Mbps
Dimensions (W x D x H) 115 x 62.5 x 31 mm
Weight 235g
Unit Output Voltage DC 56V, 1.08A
100-240V AC @50/60Hz,
Power Requirements
1.5A max.
Power Consumption 60 watts max.
Operating Temperature 0 ~ 50 degrees C
Storage Temperature -10 ~ 70 degrees C
5 ~ 95%, relative humidity, non-
Operating Humidity
condensing
5 ~ 95%, relative humidity, non-
Storage Humidity
condensing
Power over Ethernet
Ultra PoE over
4-pair UTP cable,
IEEE 802.3at
PoE Standard
Power over
Ethernet Plus End-
span/Mid-span PSE
PoE Power Supply Type End-span + Mid-span
Pair 1 End-Span: 1/2 (+), 3/6 (-)
Power Pin Assignment
Pair 2 Mid-Span: 4/5 (+), 7/8 (-)
- 4 -
PoE Power Output
Standards Conformance
Standards Compliance
Regulatory Compliance
POE-173
4. Product Outlook
in Use x 1 (Green)
Figure 1: An overview of Ultra PoE Injector.
177g Front Panel
DC 50V, 1.2A
Rear Panel
Figure 1: POE-172 & POE-173 Outlook
Ultra PoE
over 4-pair
LED Indicators
UTP cable
LED Color
POWER Green
ACTIVE Green
DC 56V/60-watt DC 50V/60-
PoE via 4-pair watt PoE via
DC 56V/30-watt 4-pair
PoE via 2-pair DC 50V/30-
watt PoE via
2-pair
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast
Ethernet
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet
IEEE 802.3at Power over Ethernet
Plus
IEEE 802.3af Power over Ethernet
FCC Part 15 Class B, CE
- 5 -
Top Panel
Bottom
Function
It indicates that the Ultra PoE Injector has
power.
It indicates the port is providing 56V (POE-
172) or 50V (POE-173) DC in-line power.
- 6 -
5. Hardware Installation
The following section describes the hardware features of
Ultra PoE Injector. Before connecting any network device
to the Ultra PoE Injector, read this chapter carefully.
5-1 Before Installation
The POE-172 is backward compatible with IEEE 802.3af
PoE and IEEE 802.3at PoE Plus standard. It is equipped
with an AC power cord with 100-240V AC input and
injects DC 56V power into the pin of the twisted pair
cable (pair 1/2 [+], 3/6 [-] and pair 4/5 [+], 7/8 [-])
for 60-watt ultra PoE injection.
Before connecting the POE-172 to your powered device
(PD), please check to ensure that your powered device
(PD) can accept 60-watt PoE power through pin 1/2 (+)
& 3/6 (-) and pin 4/5 (+) & 7/8 (-). Otherwise, it will
damage your powered device (PD).
DO NOT connect POE-173 POE port to
your non-POE network equipment Ethernet
interface. Otherwise, it will damage your
Note
network equipment.
If there is difficulty in finding a power socket for AC-DC
adapter of your non-PoE network device, the Ultra PoE
Injector and POE-171S (Ultra PoE Splitter) can provide
you with DC power for this Ethernet device conveniently
and easily.
- 7 -
The Ultra PoE Injector and POE-171S can
be installed in pair. However, the use of the
third-party device is allowed if the device
complies with IEEE 802.3at Power over
Note
Ethernet Plus and a maximum of 30 watts
of output capability.
Since the Ultra PoE injector's PoE port
supports 56V DC (POE-172) or 50V DC
(POE-173) PoE power output, please check
and assure the Powered Device's (PD)
Note
acceptable DC power range is 56V DC
or 50V DC; otherwise, it will damage the
Powered Device (PD).
5-2 Ultra PoE Injector Installation
Due to the backward capability of IEEE 802.3at/af PoE
standard, the Ultra PoE Injector can directly connect
with any IEEE 802.3at/af end-nodes such as PTZ (Pan,
Tilt & Zoom) speed dome network cameras, color touch-
screen voice over IP (VoIP) telephones, and multi-
channel wireless LAN access points. The screen in Figure
2 is shown below.
- 8 -