Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for JinkoSolar JKM350PP-72-DV
Summary of Contents for JinkoSolar JKM350PP-72-DV
- Page 1 JinkoSolar Photovoltaic Module-Eagle Dual Installation Manual...
-
Page 2: Table Of Contents
Contents General Information 1.1 Overview 1.2 Applicable Products 1.3 Warnings 2. Installation 2.1 Installation safety 2.2 Installation Condition 2.2.1 Climate condition 2.2.2 Site selection 2.2.3 Tilt angle selection 2.3 Mechanical Installation introduction Wiring and connection Maintenance and care 4.1 Visual Inspection 4.2 Cleaning 4.3 Inspection of Connector and Cable Electrical specification... -
Page 3: General Information
[键入文字] 1. General Information 1.1 Overview Thanks for choosing Jinko Solar PV modules. In order to ensure the PV modules are installed correctly, please read the following installation instructions carefully before modules are installed and used. Please remember that these products generate electricity and certain safety measures need to be taken to avoid danger. -
Page 4: Warnings
(xxx=250-305, in steps of 5, 60 cells) JKMxxxM-60-BDVP (xxx=260-315, in steps of 5, 60 cells) Group 8 JKMxxxM-60H-BDV JKMxxxM-60H-BDVP (xxx=250-305, in steps of 5, 60 cells) Notes: ① PP: the eagle+ series module ② DV: photovoltaic Module-eagle dual with 1500V ③... - Page 5 Front protective glass is utilized on the module. Broken solar module glass is an electrical safety hazard (may cause electric shock or fire). These modules cannot be repaired and should be replaced immediately. To reduce the risk of electrical shocks or burns, modules may be covered with an opaque material during installation to avoid injury.
-
Page 6: Installation
conductor current ratings, fuse sizes, and size of controls connected to the PV output. Once the PV module has been shipped to the installation site, all of the parts should be unpacked properly with care. Do not stand or step on the PV module like below pictures show. This is prohibited and there is a risk of damage to the module and cause injury for you. -
Page 7: Installation Condition
Do not work in rain, snow or windy conditions. Due to the risk of electrical shock, do not perform any work if the terminals of the PV module are wet. Use insulated tools and do not use wet tools. ... -
Page 8: Site Selection
based on the approved mounting methods. The professional system installer must be responsible for mechanical load calculation according to the system design. 2.2.2 Site selection In most applications, Jinko solar PV modules should be installed in a location where they will receive maximum sunlight throughout the year. In the Northern Hemisphere, the module should typically face south, and in the Southern Hemisphere, the modules should typically face north. -
Page 9: Mechanical Installation Introduction
Figure1: PV module tilt angle For standalone systems with batteries where the PV modules are attached to a permanent structure, the tilt angle of the PV modules should be selected to optimize the performance based on seasonal load and sunlight. In general, if the PV output is adequate when irradiance is low (e.g., winter), then the angle chosen should be adequate during the rest of the year. - Page 10 Screw Screw Top middle clamp Top end clamp EPDM EPDM Bottom end clamp Bottom end clamp Be sure to avoid shadowing effects from the module clamps. When choosing this type of clamp-mounting method, please be sure to use at least four clamps on each module, and two clamps should be attached on each long side of the module.
- Page 11 Type2 Group 5、Group 7 Mechanical Length Manual direction Load Pressure Front surface: ≤2400 Pa 120mm Back surface: ≤2400 Pa Front surface: ≤5400 Pa 150mm Back surface: ≤2400 Pa The middle of clamp should be between J and K, J=300mm,K=400mm, L=1/2 module length Type3 Group 6、Group 8 Mechanical...
-
Page 12: Wiring And Connection
Before the installation, please read the operation instructions of the PV system carefully. In addition, please completely prepare the site before the installation. Step 1:Install the rail Install the rail Step 2:Install the clamp Put the clamp into the rails Step 3:Install the module Put the module into the clamp and tighten the... -
Page 13: Maintenance And Care
b) PV module connected in series should have similar current. Modules must not be connected together to create a voltage higher than the permitted system voltage (1500VDC). The maximum number of modules in series depends on system design, the type of inverter used and environmental conditions. c) The maximum fuse rating value in an array string can be found on the product label or in the product datasheet. -
Page 14: Cleaning
c) No sharp objects are in contact with the PV module surfaces d) PV modules are not shaded by unwanted obstacles and;or foreign material e) Corrosion along the cells’ bus-bar. The corrosion is caused by moisture intrusion thought the module rear cover. Check the rear cover for damage. f) Check whether the rear cover is burn out. -
Page 15: Electrical Specification
1.25 when determining component voltage ratings, conductor current ratings, fuse sizes, and size of controls connected to the PV output. The corresponding electrical specification can be downloaded from website www.jinkosolar.com. -13-... -
Page 16: Disclaimer Of Liability
6. Disclaimer of Liability Because the use of the manual and the conditions or methods of installation, operation, use and maintenance of photovoltaic (PV) product are beyond Jinko’s control, Jinko does not accept any legal responsibility and expressly disclaims liability for any person and property damage arising from the failure to follow the installation, operation, use, maintenance provided in the manual, and for any disputes caused by no-quality reasons. - Page 17 Note _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ _____________________________________________________________________________ -15-...
- Page 18 Zhejiang Province, China 314416 Tel: +86 21 5183 8777 Tel:+86 793 858 8188 Tel: +86 573 8798 5678 Fax: +86 21 5180 8600 Fax:+86 793 846 1152 Fax: +86 573 8787 1070 www.jinkosolar.com | Technic Support: technic@jinkosolar.com | After-sales: cs@jinkosolar.com...