Connecting To A Trunk Housing - Perlick ARCTICPOUR RD060 Installation And Operation Instructions Manual

Hide thumbs

Table of Contents

CONNECTING

REFRIGERATION

GLYCOL BATH (cont.)

• Make coolant line connections and clamp using

included Oetikers (Inlet fitting is located on the

outside of the cabinet, outlet fitting is located inside

the cabinet). Insulate the glycol lines completely to

avoid condensation and unnecessary heat gain.

(Ensure that the feed line is connected to the inlet

fitting and the return line to the outlet fitting).

• Connect Low Voltage wires to the two wires with

bell connectors on them [(1) Black wire, (1) White

wire]. See Wiring Diagrams (pages 11-13) for

proper connections.

• Connect Refrigeration Deck to proper power source.

Permanently connected units should be wired per

the wiring diagram and circuit should be sized

according to the I.D. plate's electrical specifications.

The circuit should be sized in accordance with the

electrical requirements of the unit as well as in

compliance with all National and Local codes (codes

may require a separate disconnect for these units).

NOTE: Electrical circuit should be a dedicated

circuit for use only with the Refrigeration Deck.

• Make Coolant Line connections on Glycol Bath, one

to pump outlet, the other to bath return tube and

clamp using included Oetikers (Coolant Connector

feed line).

• Remove the top front panel on the bath and the

electrical box front cover.

• Connect low voltage wires to the low voltage

transformer secondary wires with bell connectors

(Blue and Yellow wires).

• Ensure power switches for the pump motor(s) are

in the OFF position. (Check transformer to ensure

the leads are connected to the low voltage side of

the transformer). Make the electrical connections

per the wiring diagram. The circuit should be sized

in accordance with the electrical requirements

e unit as well as in compliance with all

of th

National and Local Codes (codes may require

a separate disco

Electrical circuit should be a dedicated circuit

for use only with the Glycol Bath.

• Re-install Electrical Box Cover.

CONNECTING TO FLASH CHILL COILS

If the Glycol Bath includes flash chill coils, then

follow these instructions for proper connections:

Locate Glycol Bath in-line with convenient

•

point along the trunk housings to splice into

the product lines and glycol feed line within the

trunk housing (this location could be inside the

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice

DECK

nnect for these units). NOTE:

ARCTICPOUR

Operation/Installation Manual

AND

walk-in cooler, immediately outside the walk-

in cooler or anyplace along the trunk housing

up to the point of connection to the dispensing

head).

To make the proper connections, Flash Chill

•

Connector kit 68455 is required.

instructions included with kit 68455 make the

necessary connections for each product tube

and coolant line.

GLYCOL BATH INSIDE WALK-IN COOLER

• Connect and clamp incoming product lines to inlet

of flash chill tube(s). Connect and clamp outgoing

product lines to outlet of flash chill tube(s). Using

included coolant loop coils from kit 68455, (pick

the correct size based on the number of flash chill

tubes) hook up to glycol lines (see kit instructions

68455-INS).

• Tape and insulate the coolant loop and outgoing

product tubes to prevent condensation on heat

gain into the newly flash chilled product lines. The

product lines should be taped to the coolant lines

and then combined should be fully insulated to the

trunk housing insulation.

GLYCOL BATH LOCATED ALONG THE TRUNK

HOUSING.

In this scenario, the pump to maintain the product tem-

perature within the trunk housing is going to go from

the pump outlet to the flash chill coolant loop, then

from the flash chill coolant loop to the trunk housing

coolant line to the dispensing head, then back through

the trunk housing to the walk-in cooler and finally back

to the Glycol Bath.

• If the trunk housing is located along the path of

the trunk housing, then the trunk housing must

be spliced, similarly to dropping product lines at a

dispensing head, except in this case all the product

lines are being dropped to the flash chill coils along

with the feed line of the glycol circuit.

• Once all coolant and product connections are made

using the included oetiker clamps, product lines

are securely taped to the coolant lines and then all

product lines and coolant lines are insulated using

the included insulation to prevent condensation and

heat leak.