Setting Date; Setting The Radio Operation; Setting Location Address; Activating Programs - DIG LEIT Link Instruction Manual

SETTING DATE

To set the date, underscore the appropriate digits using
or and press or to change the setting.
Repeat the steps as needed for changing the calendar and
when finished press or again to underscore OK.
Press to continue.

SETTING THE RADIO OPERATION

Radio Setup available only on model XRC Controllers.
In these screens the handset allows you to limit the controller radio operation time. You will need to
limit the use of the radio controller to daylight hours to prevent power drainage of the controller. Our
suggestion is 8 AM-5 PM. This will allow the controller to operate within the window between early
morning and late afternoon. The LEIT XRC requires greater energy for radio communication than
is used for operation of the controller alone. In order to retain sufficient energy to maintain valve
control the radio on the controllers will automatically turn off in low light conditions.
Radio: 07:00am
On OK
To set the time, underscore the hour digits using
setting. Repeat the steps for changing the minute digit and AM/PM. When complete press
again to underscore OK. Press to continue.

SETTING LOCATION ADDRESS

For your convenience, 14 characters are available to set up location addresses, or any other
descriptive text, to remind you of the controller location (the text available is A-Z, 0-9 and _ ).
When setting the address, OK should be blinking.
Underscore the first digit using or and press
or to select a letter or number. Press
the next digit will blink. Repeat the steps for changing
each of the digits and when finished press
underscore OK (this is the only screen that OK is blinking). Press

ACTIVATING PROGRAMS

Note: Scheduled programs will not run unless the appropriate program number is activated
and a checkmark appears in the Active Program box.
In this screen, up to 4-programs can be activated or
deactivated. Program #01 is active (checked) by default.
To enable the controller to activate or cancel any of the
stored programs simply add or remove the checkmark.
Press or to underscore the program number
press to activate (checked). Repeat the steps to activate or deactivate additional programs as
needed. Press or again to underscore OK. Press
Date: 01/25/05
OK
Radio: 05:00pm
Off OK
or and press or to change the
NO_DESCRIPTION
or and
ID09 Location OK
or to
to continue.
Active 1234
Progs: ✔ ■ ■ ■ ■ ■ ■
OK
to continue.
17
This screen allows a complete shut off of the system for
any month of the year. By default all months are active. To
activate any month select
then press
underscore OK. Press
In this screen, the 12 months can be activated or
deactivated. By default all the months are active
(checked). To enable the controller to activate or cancel
any month of the year, simply add or remove the
checkmark. To deactivate any month, press
underscore the appropriate month and press
the steps to activate or deactivate additional months. Press
Press to continue.
This screen activates the solenoid for a test of shorts or open wires. In this screen, the short and
open valve test is deactivated by default (not checked). To enable the controller to activate one or
both of the two Short or Open features, simply add or remove the checkmark.
Press or to underscore the appropriate box and
press to activate (checked). Repeat the steps to
activate or deactivate the other option. Press
again to underscore OK. Press
Note: The test of the valve takes place when the valve is operated. Fault status will appear in
or
Check Status menu.

ACTIVATING MV/P

This screen has two options for each valve. All valves in
budget are activated by default and MV/P is deactivated by
default.
Option One MV/P: if checked, the valve number will
operate with master valve or pump.
Option Two Budget: is checked by default, the valve number is affected by the monthly budget
setting (default is 100%).
To enable the controller to use any or both of the two features, simply add or remove the
checkmark from each valve. Press
activate (checkmark) or deactivate (remove the checkmark). Repeat the steps to activate or
deactivate the other option. Press
ACTIVATING SENSORS
The Sensor In Use feature indicates whether or not a
sensor is activated and in use: if sensor is installed, select
Yes.
To enable the controller to use a sensor, the first step is to
indicate that a sensor is being used. Press
underscore Yes or No, then press
or again to underscore OK. Press
This screen, Sensor Location, indicates the location of the sensor. If MV/P or other is selected, this is
the location in which the sensor is connected via the SKIT 8821-4 adapter.
or and underscore Yes,
to select. Press or again to
to continue.
or to
to deactivate (remove the checkmark). Repeat
or
to continue.
or to checkmark the appropriate box. Press
or again to underscore OK. Press
or and
to select. Press
to continue.
18
Turn Month OFF?
0 Yes 0 No OK
Active JFMAMJ
Months: ✔✔✔✔✔ OK
or again to underscore OK.
Active CCT Test
0Short 0Open OK
Valve01 Options:
0MV/P ✔Budget OK
to
to continue.
Sensor In Use?
0 Yes 0 No OK
Sensor Location:
0 MV/P 0Other OK