Table of Contents
Advertisement
If Rain Stop is active you can manually cancel the Rain
Stop anytime by re-entering the Uplink Rain Stop screen.
Once there, press
or
to underscore Yes, then press
to select. Press
or
again to underscore OK.
Press
to continue. This will bring you back to the
Uplink Rain Stop screen.
Press
to repeat, or press
or
to move to the next feature.
SETTING UP A MONTHLY BUDGET FOR ALL PROGRAMS
Instead of changing the duration for each program, you can use the Uplink Monthly Budget feature
to increase or decrease the amount of water used during seasonally dry or wet periods on a
monthly basis. Budget adjustments can range from 10-200% in 10% increments. The LEIT
controller will automatically adjust the previously programmed duration for each program according
to the specified budget.
To skip Uplink Budget and to move to the next feature,
press
to continue.
To enter Monthly Budget, press
to continue.
If the password appears with the default (AAA), press
to continue. If the password has been changed on the
controller, enter the new controller password to continue. To
enter the password press
or
and underscore the
digit to be changed then press
or
appropriate letter. Repeat the steps for each letter. When finished, press
OK. Press
to continue.
After selecting Controller ID the handset will establish a
link with a LEIT controller. While the word Connect is
blinking, wait for a confirmation. After communication is
established, the following information screens will provide
you with 12 months of budget information. You can adjust
any month as needed. If communication is not established the No Response-Try Again screen will
appear with Yes highlighted as the default. Press
LEIT controller that has the same ID.
Budget information for the previous 12 months will appear
with January first and 100% as the default. Press the
or
to underscore the percentage digits. Press
increase or
to decrease the percentage (in
increments of 10%). Press the
or
to underscore OK.
Press
to advance to the next month and repeat the steps for each of the months as needed. If
any of the months have been changed, the new information will need to be uploaded by
establishing a link with the LEIT controller with same ID address. Press
Communication has been established and the newly
revised setting has been accepted. Press
Press
to repeat. Press
or
to move to the next feature.
Cancel Rainstop?
0Yes 0No
OK
UPLINK
BUDGET?
Password: AAA
OK
to select the
or
to underscore
Connect ID: 12
Controller:
again to re-initiate communication with a
JAN
100%
to
Budget:
OK
to continue.
Revised
to continue.
BUDGET
9
REVIEW A CONTROLLER STATUS
This feature allows you to review the current controller status for the time, date, sensor activation,
active program or valve, manual run, rain stop progress, month off if any, short or open circuit in
valve wiring or valve open. It also provides information on the controller's power range and
availability for communication.
To review Check Status press
. To skip Check Status
and move to the next feature, press
or
After selecting Controller ID address, the handset will
establish a link with a LEIT controller that has this same
address. While the word Connect is blinking, wait for a
confirmation. After communication is established, the
following information screens will provide a status report
on the controller. If communication is not established the No Response-Try Again screen will appear
with Yes highlighted as the default. Press
controller that has the same ID.
This screen appears if the controller is low on power.
Press
to continue.
This screen appears if any program or valve is active.
Press
to continue.
This screen appears if any program or group of valves is
active. Press
to continue.
This screen appears if the Manual Run is in progress.
Press
to continue.
This screen appears if Rain Stop is active. Press
continue.
This screen appears if irrigation has stopped for a full
month. Press
to continue.
This screen appears if the valve wiring is open. Press
to continue.
UPLINK
to continue.
STATUS?
Connect ID: 12
Controller:
OK
again to re-initiate communication with a LEIT
Cont:12 voltage
*LOW*
OK
Prog:X Active
Valve xx Open
OK
Prog:X Active
GRPxx:yy Open OK
Manrun Active
Valve:XX Open
OK
to
Rainstop Active
xx More Days
OK
Irrigation Stop
for Month XXX
OK
Station xx O/C
OK
Wiring Fault
10
Advertisement
Table of Contents
