Page 2
The use of a water or sleep flotation mattress is prohibited. Replacement parts, including additional guardrails, may be obtained from any of Walker Edison Furniture Company’s dealers or by contacting us online at www.walkeredison.com. DO NOT use substitute parts. Contact the manufacturer or dealer for replacement parts.
Assembly Options Option A - Ladder Left To build this option follow Steps 1-11 and Steps 12A-16A. Option B - Ladder Right To build this option follow Steps 1-11 and Steps 12B-16B.
Page 6
Attach guardrail (13) and crossbar (11) to posts (1,4) using bolts (A). Tighten bolts (A) with wrench (G). Please note the position of all pre-drilled holes as shown above before attaching bunk bed parts together. Attach second guardrail (13) and crossbar (12) to posts (2,3) using bolts (A). Tighten bolts (A) with wrench (G). Please note the position of all pre-drilled holes as shown above before attaching bunk bed parts together.
Page 7
Attach support leg (17) to crossbar (16) using bolts (A). Tighten bolts (A) with wrench (G). Attach crossbar (7) to post (1), crossbars (8,10) to post (4) and crossbar (16) to crossbar (11) using bolts (A). Please note the position of all pre-drilled holes as shown above before attaching bunk bed parts together. Tighten bolts (A) with wrench (G).
Page 8
Attach opposite end of crossbar (7) to post (2), opposite ends of crossbars (8,10) to post (3) and opposite end of crossbar (16) to crossbar (12) using bolts (A). Please note the position of all pre-drilled holes as shown above before attaching bunk bed parts together. Tighten bolts (A) with wrench (G).
Page 9
Roll mattress support slats (19) out along the upper bunk and secure them to the upper bunk using anchors (F) and bolts (A) where indicated above. Bolts (A) will screw directly into crossbars (7,8). Tighten bolts (A) with wrench (G). Attach guardrail (18) to posts (3,4) using bolts (A).
Page 10
Attach second guardrail (18) to posts (1,2) using bolts (A). Secure guardrail (18) to crossbar (7) using bolts (B). Tighten all bolts (A,B) with wrench (G). Attach extension leg (5) to post (1) and extension leg (6) to post (2) using bolts (A). Tighten bolts (A) with wrench (G).
Page 11
Attach crossbar (9) to extension legs (5,6) using bolts ( B). Tighten bolts (A,B) with wrench (G). Roll mattress support slats (20) out along the lower bunk and secure them to the lower bunk using anchors (F) and bolts (A) where indicated above. Bolts (A) will screw directyly into crossbars (9,10). Tighten bolts (A) with wrench (G).
Page 12
Screw double-ended bolts (D) into post (4). Slide washers (E) onto double-ended bolts (D). Screw ladder rungs (15) onto double-ended bolts (D). Ladder rungs (15) will fit into washers (E).
Page 13
Fit washers (E) onto opposite ends of ladder rungs (15). Attach ladder support rail (14) to ladder rungs (15) using bolts (C). Tighten bolts (C) with wrench (G). Secure ladder support rail (14) to guardrail (13) using bolt (A) and to crossbar (11) using bolt (B). Tighten bolts (A,B) with wrench (G).
Page 15
Screw double-ended bolts (D) into post (3). Slide washers (E) onto double-ended bolts (D). Screw ladder rungs (15) onto double-ended bolts (D). Ladder rungs (15) will fit into washers (E).
Page 16
Fit washers (E) onto opposite ends of ladder rungs (15). Attach ladder support rail (14) to ladder rungs (15) using bolts (C). Tighten bolts (C) with wrench (G). Secure ladder support rail (14) to guardrail (13) using bolt (A) and to crossbar (12) using bolt (B). Tighten bolts (A,B) with wrench (G).