Related Manuals for Walker Edison BTOT Series
Summary of Contents for Walker Edison BTOT Series
- Page 1 ITEM#: BTOT Assembly Instructions Please visit our website for the most current instructions, assembly tips, report damage, or request parts. www.walkeredison.com Revised 03/2017 Copyright © 2009, by Walker Edison Furniture Co., LLC. All rights reserved.
- Page 6 Assembly the four support posts by combining parts B, C, and A; then parts E, C, and D as shown in the illustration. Secure these parts together using screws (1) and washers (2). Be sure to tighten firmly using wrench (11).
- Page 7 Place guardrails (P) between the assembled support posts as shown in the illustration. Secure guardrails to the support posts using screws (1) and washers (2) as shown in the illustration. Be sure to tighten firmly using wrench (11).
- Page 8 Attach legs (N) to the lower cross bars (G, I) using screws (1) and washers (2) as shown in the illustration. Tighten screws using hex wrench (11).
- Page 9 Attach lower cross bars (G, I) and upper cross bars (F, H) to the end supports in Step 3 using washers (2) and screws (1) as shown in the illustration. Ensure the slots on the cross bars are facing inward as shown in the illustration. Be sure to tighten all screws firmly using wrench (11).
- Page 10 Attach another end supports assembled in Step 3 to bed frame using washers (2) and screws (1) as shown in the illustration. Ensure the slots on the cross bars are facing inward as step 6. Be sure to tighten all screws firmly using wrench (11).
- Page 11 Insert mattress support bars (O) into the slots on the cross bars as shown in the illustration. Snap plastic tab locks (8) into each slot to lock the mattress support bars in place.Snap plastic links (9) into the middle of the mattress support bars as shown in the illustration.
- Page 12 Insert mattress support bars (O) into the slots on the cross bars as shown in the illustration. Snap plastic tab locks (8) into each slot to lock the mattress support bars in place. Snap plastic links (9) into the middle of the mattress support bars as shown in the illustration.
- Page 13 Attach the ladder steps (M) to the ladder support posts (L) using screws (5) and washers (6) as shown in the illustration.
- Page 14 Attach ladder frame assembly to the upper cross bar on the right side using screw (1) and washer (2) on the left side using screw (3) and washer (4) as shown in the illustration. Attach ladder support posts to the lower cross bar using screws (4) and washers (3) as shown in the illustration Attach open guardrail (K) to the upper cross bar using screws (4) and washers (3), then attach upper guardrail (K) to the support post using screw (1) and washer (2) as diagram shown.
- Page 15 Attach back upper guardrail (J) to the back frame support beams using screws (1) and washer (2) as shown in the illustration. Attach guardrail to cross bar (F) using screws (4) and washers (3), tighten with wrench (12). Be sure to tighten all screws firmly.
- Page 16 Place plastic plugs (10) into the holes in the front cross bars as shown in the illustration. Snap plastic links (9) into the middle of the mattress support bars as shown in the illustration...
- Page 17 Attach ladder frame assembly to the upper cross bar on the right side using screw (1) and washer (2) on the left side using screw (3) and washer (4) as shown in the illustration. Attach ladder support posts to the lower cross bar using screws (4) and washers (3) as shown in the illustration Attach open guardrail (K) to the upper cross bar using screws (4) and washers (3), then attach upper guardrail (K) to the support post using screw (1) and washer (2) as diagram shown.
- Page 18 Attach back upper guardrail (J) to the back frame support beams using screws (1) and washers (2) as shown in the illustration. Attach guardrail to cross bar (F) using screws (4) and washers (3), tighten with wrench (12). Be sure to tighten all screws firmly.
- Page 19 Place plastic plugs (10) into the holes in the front cross bars as shown in the illustration. Snap plastic links (9) into the middle of the mattress support bars as shown in the illustration.
- Page 21 Loosen and remove the ladder and the open guardrail (K) from the bed frame.
- Page 22 Loosen and remove the back upper guardrail (J) from the bed frame.
- Page 23 Lossen bolts where upper bunk connects with lower bunk .
- Page 24 Lift and separate the bunks.
- Page 25 Attach legs (N) to the lower cross bars (H, F) using screws (1) and washers (2) as shown in the illustration. Tighten screws using hex wrench (11). Attach plastic end caps (7) as shown in the illustration.
- Page 26 Place plastic plugs (10) into the holes in the front cross bars as shown in the illustration. Insert screws (1) to support (A, D) using wrench (11).