NEC Express5800/R120f-1M Maintenance Manual page 147

Chapter 3 Appendix
Error Message
B006 Expansion ROM not
initialized - PCI
Slot 1D
Expansion ROM not initialized
B007
- PCI
Slot 2D
Expansion ROM not initialized
B008
- PCI
Slot 3D
B01A Expansion ROM not
initialized - PCI
Slot 1A
B022 Serial Port Configuration
Overlapped.
B030 PCI System Error on
Bus/Device/Function
B040 PCI Parity Error on
Bus/Device/Function
B211 PCI Slot 1A - PCIe Link
Failure
B212 PCI Slot 1B - PCIe Link
Failure
B215 PCI Slot 1C - PCIe Link
Failure
B216 PCI Slot 2C - PCIe Link
Failure
B217 PCI Slot 3C - PCIe Link
Failure
B218 PCI Slot 1D - PCIe Link
Failure
PCI Slot 2D - PCIe Link Failure Connection failure of PCIe bus
B219
PCI Slot 3D - PCIe Link Failure Connection failure of PCIe bus
B21A
B231 PCI Slot 1A - PCIE Link Width
Error
B232 PCI Slot 1B - PCIE Link Width
Error
B234 PCI Slot 1C - PCIE Link Width
Error
B235 PCI Slot 2C - PCIE Link Width
Error
B236 PCI Slot 3C - PCIE Link Width
Error
B237 PCI Slot 1D - PCIE Link Width
Error
B238 PCI Slot 2D - PCIe Link Width
Error
B239 PCI Slot 3D - PCIe Link Width
Error
B271 PCI Slot 1A - PCIe Link Speed
Error
B272 PCI Slot 1B - PCIe Link Speed
Error
B273 PCI Slot 2B - PCIe Link Speed
Error
Cause
Option ROM expansion in PCI
slot 1D failed.
Option ROM expansion in PCI
slot 2D failed.
Option ROM expansion in PCI
slot 3D failed.
Option ROM expansion in PCI
slot 1A failed.
Overlapping serial port
configuration was detected.
PCI SERR was detected.
PCI PERR was detected.
Connection failure of PCIe bus
was detected on PCI slot 1A.
Connection failure of PCIe bus
was detected on PCI slot 1B.
Connection failure of PCIe bus
was detected on PCI slot 1C.
Connection failure of PCIe bus
was detected on PCI slot 2C.
Connection failure of PCIe bus
was detected on PCI slot 3C.
Connection failure of PCIe bus
was detected on PCI slot 1D.
was detected on PCI slot 2D.
was detected on PCI slot 3D.
A Link Width error was detected
in PCI Slot 1A.
A Link Width error was detected
in PCI Slot 1B.
A Link Width error was detected
in PCI Slot 1C.
A Link Width error was detected
in PCI Slot 2C.
A Link Width error was detected
in PCI Slot 3C.
A Link Width error was detected
in PCI Slot 1D.
A Link Width error was detected
in PCI Slot 2D.
A Link Width error was detected
in PCI Slot 3D.
Link Speed error was detected
on PCI Slot 1A.
Link Speed error was detected
on PCI Slot 1B.
Link Speed error was detected
on PCI Slot 2B.
Express5800/R120f-1M, R120f-2M Maintenance Guide
Solution
Disable expansion of option ROM of the option
board that is not used for OS boot.
Run SETUP, and select Advanced → PCI
Configuration → PCI Device Controller and
Option ROM Settings → PCIxx Slot Option
ROM → Disabled. (xx: PCI slot number)
Start SETUP, select Advanced → Serial Port
Configuration, and specify the setting again in a
way that the values of Base I/O or Interrupt in
Serial Port A and Serial Port B will not be the
same.
Contact your sales representative.
1. POST Error Message
147