Watec WAT-400D Operation Manual

Waterproof Color CCD Camera
WAT- - - - 400D WAT WAT WAT
Operation Manual
This Operation Manual covers safety, camera functions, installation and the
correct operating procedure for the WAT-400D. First, we ask you to read this
Operation Manual thoroughly, then install and operate the WAT-400D as
advised. In addition, for future reference, we also advise safe keeping of this
manual.
Please contact the distributor or dealer from which the WAT-400D was
purchased, if you do not understand the installation, operation or safety
instructions laid out in this manual. Not understanding the contents of the
Operation Manual sufficiently may cause damage to the camera.
Guide to the safety symbols
The meanings of the symbols used in this operation manual are:
When you do not adhere to or take notice of the "Danger" sign, it
may lead to a serious accident such as death or injury caused
Danger
by fire or electric shock.
When you do not adhere to or take notice of the "Warning" sign,
War ni ng
it may cause severe damage such as a physical injury.
When you do not adhere to or take notice of the "Caution" sign,
it may incur injury and cause damage to peripheral objects in the
Cauti on
immediate surroundings.
Cautions for safety
The WAT-400D is designed to be used safely; however, electrical goods
may lead to a physical accident caused by fire and electric shock if not used
correctly. Therefore, please keep and read the "Cautions for safety" for
protection against accidents.
• Do not disassemble and/or modify the WAT- 400D.
Danger
• Do not operate any current-carrying part with wet hands.
.
• Use only the AD-156 with the WAT- 400D
War ni ng
• Do not use the WAT- 400D under unusual environmental
conditions.
The WAT-400D is specified as waterproof. However, the
WAT-400D is not compliant with dust-proof and explosion-
proof standards.
• Should the camera not work properly, switch off the power
immediately. Then check the camera according to the
"Problems and Trouble shooting" section.
• Avoid the striking of hard objects or dropping the
Cauti on
WAT- 400D.
The WAT-400D uses high quality electrical parts and
precision components.
• The WAT-400RX must be used with the WAT-400D.
Connect the WAT-400RX with the AD-156, monitor, and the
WAT-400D.
• Do not install the WAT- 400D in a position subject to direct
sunlight.
Sunlight shinning directly onto the WAT-400D lens can cause
damage to the CCD.
• Select a stable place for installation of the WAT- 400D.
Use a support of durable strength around an installation
position on a ceiling or wall when a camera stand or tripod is
used.
• Do not move the WAT- 400D with the cables connected.
Before moving the WAT-400D, always remove the video
cable and power cable from the rear of the camera first.
• Avoid using the WAT- 400D near any strong
ielectromagnetic field.
Avoid emission sources of electromagnetic waves when the
WAT-400D is installed into main equipment.
• Dry the WAT- 400D well after use.
400D 400D 400D
When the WAT-400D is used in seawater, flush well with pure
water, and then wipe. If the WAT-400D is steeped in water for
many hours or left without wiping after use, the surface of the
WAT-400D may become white.
EMC Conformity
The WAT-400D is in conformity with EMC test standards carried out by
authorized organizations in Japan.
NTSC FCC Part15 class B
P A L EN61000-6-3 / EN50130-4
Do not modify the WAT-400D. A Modified camera may not
Danger
conform to EMC test standards.
Waterproof Conformity
The external body of the WAT- 400D is in conformity with the following
waterproof standard.
JIS C 0920 (IEC60529)
Degrees of protection provided by enclosures: IPX8
t(Water pressure: 2kgf/cm
※Waterproof capability of the WAT-400D is confirmed according to the
above conditions. This waterproof standard does not cover the quality of
the operation under unusual condition.
For ④VIDEO OUT/POWER IN, this part is not included in the
Cauti on compatible range of the waterproof standard. Treat the
connecter area for waterproofing if needed.
Problems and Trouble Shooting
If any of the following problems occur when using the WAT- 400D,
• An optimal picture cannot be obtained, after checking that all the cables
and connections are correctly in place.
Smoke or any unusual odor emerges from the WAT-400D.
•
An object becomes embedded or a quantity of liquid seeps into the camera
•
housing.
More than the recommended voltage or/and amperage has been applied
•
to the WAT-400D by mistake.
Anything unusual occurring to any equipment connected to the WAT-400D.
•
Disconnect the camera immediately according to the following
procedures:
①Switch off the main power supply to the camera.
②Remove the power and video cables connected to the WAT-400D.
③Contact the distributor or dealer from which the WAT-400D was
purchased.
Contents
Check to make sure all parts are present before use.
WAT- 400D
Description of parts
①VIDEO OUT (MONITOR)
・ ・ ・ ・ BNC for connecting with the monitor. Use a cable with 75Ω impedance,
such as RG-58/U.
②POWER IN (POWER IN)
・ ・ ・ ・ The terminal for connecting the AD-156.
③BNC for connection of the WAT-400D (CAMERA)
・ ・ ・ ・ BNC for connecting with ④VIDEO OUT/POWER IN.
④VIDEO OUT/POWER IN
・ ・ ・ ・ The BNC coaxial cable for video out and power in.
⑤BRACKET MOUNTING SCREWS
・ ・ ・ ・ The screws for mounting the bracket to the camera.
⑥BRACKET
・ ・ ・ ・ The bracket for fixing to the camera.
2
, Test time: 2 hours)
⑦TRIPOD MOUNTING SCREW HOLES
・ ・ ・ ・ Mounting holes for stands. The size of these threads are 1/4", 20 threads,
4.5±0.2mm, which is the same as any standard camera tripod (U1/4").
⑧HOUSING MAIN BODY
・ ・ ・ ・ This case is uses aluminum and is given alumite treatment
⑨FRONT GLASS (Tempered glass)
・ ・ ・ ・ Dirt, water or oil deposits on the front glass will cause an unclear picture
on the monitor and scratches might become permanent damage. Do not
dismount the front glass.
Set-up and Operation
1) Ensure that the power to the WAT-400D and the peripheral equipment
is turned off before making any connections.
2) Connect the BNC ④VIDEO OUT/POWER IN of the WAT-400D to
③BNC to the WAT-400RX. When extending the cable beyond 10 meters,
use a coaxial cable with 75Ω impedance, such as an RG-58/U.
The maximum cable length is 200m using RG-58/U.
3) Connect ①VIDEO OUT (MONITOR) on the WAT-400RX with the
monitor, using a coaxial cable with 75Ω impedance, such as an
RG-58/U. Select a monitor with the same television system as the
WAT-400D: NTSC or PAL. A monitor with more than 500TV lines is
recommended.
4) Connect the attached AC adaptor (AD-156) to ②POWER IN on the
WAT-400RX.
5) Turn on the power to the WAT-400D, monitor and all other allied
equipment. When a picture cannot be obtained on the monitor, check
and follow the procedure mentioned in the【Problems and Trouble
Shooting】section.
6) When a change of installation position is required, set ⑥BRACKET
to your required position after removing ⑤ BRACKET MOUNTING
SCREWS from the WAT-400D, then retighten ⑤BRACKET MOUNTING
SCREWS firmly. Angular settings for ceiling and wall are also available.
Receiver (WAT- 400RX)
< WAT-400D Back view >
AC adaptor (AD-156)

Wiring Diagram

The following diagram is the basic connection of the WAT-400D with the
AD-156 and monitor.

Specifications

Model WAT- 400D (NTSC)
Pick-up Element
Number of Total Pixels
Number of
Effective Pixels
Unit Cell Size 6.4μm(H)×7.5μm(V)
Imaging system
Sync. System
Scanning System
Video Output Composite video, 1.0 V(p-p), 75Ω(Unbalanced)
Resolution (H)
Minimum Illumination
S/N
A/E mode
White Balance
AGC
Gamma Characteristics
Back Light
Compensation
Power Supply
Power Consumption
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Built-in Lens
Cable Length
Max. Cable Length
Size
Weight
※Maximum cable length should be 200 meters using a RG-58/U cable to ensure
an adequate electrical performance, but waterproof performance is not
guaranteed. For waterproof, please refer to the【Waterproof Conformity】
section.
■SELECTABLE FACTORY SETTING
AE mode (Fixed)
White balance
Mirror image
Design and specifications are subject to change without notice.
•
Watec is not responsible for any inconvenience or the attendant damages to
•
the video and monitoring recording equipment caused by misuse, mis-
operation or improper wiring of our equipment.
If for any reason the WAT-400D does not work properly, or if you have any
•
questions regarding installation or operation, please contact the distributor or
dealer from which it was purchased.
Contact information
Add.: 254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,
Yamagata-Ken, 997-0017 Japan
TEL: +81-235-23-4400 FAX: +81-235-23-4409
Email: info-o@watec.co.jp
URL: http://www.watec.net
< ⑥BRACKET >
WAT- 400D (PAL)
1/3 inch interline transfer CCD image sensor
811(H)×508(V) 795(H)×595(V)
768(H)×494(V) 752(H)×582(V)
6.5μm(H)×6.3μm(V)
Ye, Cy, Mg, and G complementary
color mosaic filters on chip
Internal
2:1 interlaced
More than 450TVL (Center)
2.0 lx. F1.6
More than 50dB (AGC=3dB, γ=1.0)
1/60 sec. 1/50 sec.
ATW
3 - 24dB
γ≒0.45
ON
DC+15V±10%
2.03W (135mA)
-10 - +50℃ (Without condensation)
Less than 95% RH
-30 - +70℃ (Without condensation)
Less than 95% RH
Auto-iris lens (f=2.8 F1.6)
RG-58/U 10m
※
RG-58/U 200m
φ72 × 116 (mm)
Approx. 900g (Including RG-58/U 10m cable)
1/60, 1/100 sec. 1/50, 1/120 sec.
1/250, 1/500, 1/1000, 1/2000,
1/5000, 1/10000, 1/20000, 1/50000 sec.
ATW, Preset (3200K, 5100K, 8200K)
ON / OFF
Watec Co., Ltd. Watec Co., Ltd. Watec Co., Ltd. Watec Co., Ltd.
1473Z00-Y2077001