Wæ
Monochrome CCD Camera
wAT-f 20N+
Operation Manual
This Operation Manual covers safety, camera functions, installation and ihe
correct operating procedure for the WAT-120N+. First, we ask you to read
this Operation Manual thoroughly, then install and operate the WAT-I20N+
as advised. In addition, for future reference, we also advise safekeeping of
this manual.
Please contact the distributor or dealer from which the WAT-120N+ was
purchased, if you do not understand the installation, operation or safety
instructions laid out in this manual. Not understanding the content3 of the
Operation Manual sufficiently may cause damage to the camera.
. Do not move the WAT-120N+ with the cables connected.
Before moving the WAT-120N+, always remove the video
cable and power cable from the rear of the camera first.
. Avoad using the WAT-120N+ near any strong
electromagnetic field.
After installing into main equipment. if the WAT-120N+ is
exposed to electromagnetic waves causing the monitored
image to become distorted, we recommend the camera be
shielded by appropriate protective casing
tr-il;l
tÂ;;;l
6il;i
Problems and Tro$ble $hooting
ffiffiï
Guide to the. Sg-&#,,S tblts
The definitions of the symbols used in this operation manual are
When you do not adhere to or take notice of the "Danger" sign'
it may lead to a serious accident such as death or injury caused
by fire or electric shock.
When you do not adhere to or take notice of the "Warning" sign,
it may cause severe damage such as a physical injury.
When you do not adhere to or take notice of the "Caution" sign'
it may incur injury and cause damage to peripheral objects in
the immediate surroundings.
Gautions $or SâfetY
The WAT-120N+ is designed to be used safely, however. it may lead to a
physical accident caused by fire and electric shock if not used correctly'
Therefore, please keep and read the "Cautions for safety for protection
aoainst accidents.
. Do not disassemble and/or modify the WAT-120N+.
. Do not operate the WAT-120N+ wath wet hands'
lf any of the following problems occur when using the WAT-120N+'
'
. An optimal picture cannot be obtained. after checking that all the cables
and connections are correctly in place
. Smoke or any unusual odor emerges from the WAT-120N+
.An object becomes embedded or a quantity of liquid seeps Into the
6mera houeingf
. M o r e t h a n t h e r e c o m m e n d e d v o l t a g e o r a n d a m p e r a g e h a s b e e n a p p l l e d
to the WAT-120N+ by mistake
. A n y t h i n g u n u s u a l o c c u r r i n g t o a n y e q u i p m e n t c o n n e c t e d t o t h e
WAT-120N+
Disconnect the camera immediately according to the following procedures:
OSwrtch off the main power supply to the camera.
@Remove the power and video cables connected to the WAT-120N+.
OContact the distributor or dealer from which the WAT-120N+ was
ourchased.
About EitC
The WAT-120N+ is in conformity with EMC test standards carried out by
authorized organizations in Japan.
NTSC
FcC Partl 5 class B
P A L
E N 6 1 0 0 G 6 - 3 / E N 5 0 1 3 0 - 4
Do not modify the WAT-120N+ A modified camera may nol
conform to EMC test standards
Gontents
Using the contents f|gures be|ow, check to make sure a|| parts are present
before use.
f /r ..
--
.--l . Use a stabilized power adaptor designed for DC+12Vt
l4Ytt
n ' n*l
10%, with a current capacity of more than 250mA for the
WAT-120N+'
The recommended voltage is DC+12Vt10%.
. Do not expose the WAT-120N+ to wetness or high
moisture conditions.
The WAT-120N+ is designed and approved for indoor use only.
The WAT-'|20N+ is not water-resistant or waterproof . lf the
location of the camera is outdoors or in an outdoor like
environment, we recommend that you use an outdoor camera
housing.
. Protect the WAT-120N+ from condensation.
Keep the WAT-120N+ dry at all times during storage and
operation.
. Should the camera not work properly, switch off the power
immediately. Then check the camera according to the
"Problems and Trouble Shooting" section
. Avoid the striking of hard obiects or dropping the WAT-
1 2 0 N + .
The WAT-120N+ uses high quality electrical parts and
precision comPonents.
. bo not connect any power supply directly to the video out
terminal of the unit.
Do not connect the WAT-120N+ with any monitor uslng a
video/power single transmission terminal. The WAT-I20N+ is
not designed foi use with this type of equipment We also
advise yôu to read the operation manual of the monitor you
plan to use before any connections are made.
. Do not install the WAT-120N+ in a position subiect to
direct sunlight.
Sunlight shinning directly onto the WAT-120N+ lens can cause
damage to the CCD.
. Seleci a stable place for installation of the WAT-120N+'
Use a support of durable strength around an. installation
position on a ceiling or wall when a camera stand or tripod is
used.
Lens Mount CaP
WAT-120N+
!^rÂT-120N+RC
'Caæ Amr
3m)
ll
_J
n--rf----. -r
rltt
-u
ru
C-moun-tAdaptor
Hex. Vvtench
DC Plug
lris Connector
(34CMA-R)
@
@
a,
0
@
@
o
@
ro
@
@
Need help?
Do you have a question about the WAT-120N+ and is the answer not in the manual?
Questions and answers