Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Dahua TPC-PT8620A-B
Summary of Contents for Dahua TPC-PT8620A-B
- Page 1 Thermal High-Speed Hybrid PTZ Camera Quick Start Guide Version 1.0.1...
- Page 2 Welcome Thank you for purchasing our network cameras. This user’s manual is designed to be a reference tool for using your product. Please read the following safeguards and warnings carefully before you use this series product. Please keep this user’s manual well for future reference.
-
Page 3: Cybersecurity Recommendations
Cybersecurity Recommendations Mandatory actions to be taken towards cybersecurity 1. Change Passwords and Use Strong Passwords: The number one reason systems get “hacked” is due to having weak or default passwords. It is recommended to change default passwords immediately and choose a strong password whenever possible. - Page 4 7. Disable Auto-Login on SmartPSS: Those using SmartPSS to view their system and on a computer that is used by multiple people should disable auto-login. This adds a layer of security to prevent users without the appropriate credentials from accessing the system. 8.
-
Page 5: Important Safeguards And Warnings
The network your NVR and IP camera resides on should not be the same network as your public computer network. This will prevent any visitors or unwanted guests from getting access to the same network the security system needs in order to function properly. Important Safeguards and Warnings Electrical safety All installation and operation should conform to your local electrical safety codes. - Page 6 Make sure the power supply is correct before operating the device. A readily accessible disconnect device shall be incorporated in the building installation wiring Prevent the power cable from being trampled or pressed, especially the plug, power socket and the ...
- Page 7 Warnings Please modify the default password after login to avoid being stolen. Use the standard components provided by manufacturer and make sure the device is installed and fixed by professional engineers. The surface of the image sensor should not be exposed to laser beam radiation in an environment ...
-
Page 8: Fcc Information
All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the Guide. Please contact the customer service for the latest program and supplementary documentation. There still might be deviation in technical data, functions and operations description, or errors in ... - Page 9 Note Please refer to the disk for more details, check and download the corresponding user’s manual and tool. Before installation, please open the package and check all the components are included. Contact your local retailer as soon as possible if something is broken in your package. ...
-
Page 10: Table Of Contents
Table of Contents Cybersecurity Recommendations ......................II 1 Device Framework ..........................3 1.1 Device External Cable ........................3 1.2 Dimension ............................. 5 2 Device Installation ..........................6 2.1 Preparation before Installation ...................... 6 2.1.1 Check Installation Space and Intensity ................6 2.1.2 Cable Preparation ....................... -
Page 11: Device Framework
1 Device Framework 1.1 Device External Cable Note The following structure figure is for reference only. It is only used to know the functions of cable ports. There might be some minor differences between different devices, so please refer ... - Page 12 Port Port name Connector Function description Audio input Input audio signal, receive analog audio AUDIO IN port signal from pickup and other devices. Audio output Output audio signal to speaker and other AUDIO OUT port devices. Audio AUDIO GND grounding terminal Connect to standard Ethernet cable.
-
Page 13: Dimension
1.2 Dimension Note The following figures are for reference only, which are only used to know the device dimension. Refer to Figure 1-3 and Figure 1-4 for the device dimension and pole-mounted chassis respectively. The unit is mm (inch). Figure 1-3 Figure 1-4... -
Page 14: Device Installation
2 Device Installation 2.1 Preparation before Installation 2.1.1 Check Installation Space and Intensity Make sure the installation site has enough space to hold the device and its mounting structural components. Please make sure the ceiling and wall where the bullet is installed can sustain at least 8x weight of bullet and its mounting structural components. -
Page 15: Device Installation
Step 1 Loosen the screws on the lower cover. You can see the SD card slot and reset button after opening the lower cover, which is shown in Figure 2-1. Figure 2-1 Note Long press the reset button for 4 to 5 seconds to restore device factory default setting. Step 2 Insert the SD card into the slot, the card slot is elastic, so it only needs to press the SD card slightly to make it inserted. - Page 16 Step 1 Fix the device onto the mounting surface. Dig three mounting hole sites on the cement block according to the mounting holes, Make sure the size of hole diameter needs to be in accordance with expansion bolt, and there shall be no deviation for hole site.
-
Page 17: Bottom Cable Exit
After pulling the network cable without crystal head through main body of waterproof connector, fixing rubber ring and waterproof fastening cover, make the crystal connector of network cable and then insert it into the network cable. Put the main body of waterproof connector on the network port and rotate it clockwise to lock the network port and waterproof connector firmly. - Page 18 Align the screw holes of PTZ bottom with the mounting hole sites of pole- mounted bracket, and then use fixing bolt to fix the device on the pole- mounted bracket. Figure 2-5 Step 3 Connect the external cable well according to the use requirement. Please refer to step 2 in 2.3.1 Side Cable Exit for more details.
-
Page 19: Device Configuration
3 Device Configuration 3.1 Device Initialization It needs to set the user password when logging in for the first time (the username is admin by default). The figures listed in the following chapter are for reference only. There is difference about interface between different devices, please refer to the actual device for more details. -
Page 20: Modify Ip Address
Step 3 Click Save to complete initialization. 3.2 Modify IP Address In order to make the camera get access to network smoothly, please plan IP address reasonably according to the actual network environment. Step 1 Log in camera WEB interface in the IE browser. Note ... -
Page 21: Alarm Setup
Step 1 Log in camera WEB interface in the IE browser. Note IP address is the one which has been modified. Default user is admin; the password has been set during device initialization. Step 2 Click Login and the system will display the WEB main interface, which is shown in Figure 3-3. Note It will prompt you to install plug-in for the first system login, please save and install plug-in according to prompt. - Page 22 click Save. The interface of alarm setup is shown in Figure 3-4. Alarm input is corresponding to the alarm input port of device I/O cable. It is to set corresponding NO and NC according to the high and low level signal generated by alarm input device when alarm occurs.
- Page 23 Figure 3-6 Alarm output: port ALARM_OUT and ALARM_COM form a switch, which can be used to provide alarm output. Normally the switch is on, the switch will be off when there is alarm output.
-
Page 24: Appendix Ⅰ Lightening Protection And Surge Protection
4 Appendix Ⅰ Lightening Protection and Surge Protection This series speed dome adopts TVS lighting protection technology. It can effectively prevent damages from various pulse signals below 6000W, such as sudden lighting and surge. While maintaining your local electrical safety code, you still need to take necessary precaution measures when installing the speed dome in the outdoor environment.
Need help?
Do you have a question about the TPC-PT8620A-B and is the answer not in the manual?
Questions and answers