Subscribe to Our Youtube Channel
Related Manuals for Lumberjack TS250SL
Summary of Contents for Lumberjack TS250SL
- Page 1 SAFETY AND OPERATING MANUAL 250mm Table Saw With Side Extensions TS250SL ORIGINAL INSTRUCTIONS TS250SL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Welcome to Lumberjack! Dear customer, Congratulations on your purchase. Before using the product for the first time please be sure to read these instructions for use. They provide you with all information necessary for using the product safely and to ensure its long service life. -
Page 3: General Power Tool Safety Warnings
A wrench or a key left c) Do not expose power tools to rain or wet attached to a rotating part of the power tool may conditions. Water entering a power tool will result in personal injury. increase the risk of electric shock. TS250SL... - Page 4 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. TS250SL...
- Page 5 Unsharpened or improperly set saw piece. blades produce narrow kerfs causing excessive e) Keep handles dry, clean, and free from oil friction, blade binding and kickback. and grease. Greasy, oily handles are slippery causing loss of control. TS250SL...
- Page 6 Be aware that laser light reflected working. Damaged cables increase the risk of an off of a mirror or any other reflective surfaces can electric shock. also be dangerous. TS250SL...
- Page 7 The smaller the gauge number of the wire the greater the capacity of the cord. m) Do not attempt to change any parts of the laser guide. e) When using a cable reel, always unwind the cable completely. TS250SL...
- Page 8 Caution! Risk of Injury! Do Caution! Wear ear defenders. The not reach into the running impact of noise can cause damage saw blade to hearing. Caution! Wear a dust mask. Class II Double Insulated TS250SL...
-
Page 9: Machine Details And Product Features
Support struts Long(2x) 19.Short cross brace Support struts short(2x) 20.Hexagon head screw Extension table support rod(4x) 21.Hexagon nut Push stick 22a.Saw blade spanner Manual 22b.Saw blade spanner 23.Support struts Fasteners 24. Extension table support rod TS250SL AIR6V AIR6V AIR6V AIR6V... - Page 10 MACHINE DETAILS AND PRODUCT FEATURES TS250SL AIR6V AIR6V AIR6V AIR6V...
-
Page 11: Assembly
Certain dust such as oak or beech dust is considered carcinogenic, particularly in combination with wood treatment additives (chromate, wood preservatives). Materials containing asbestos may only be processed by experts. TS250SL... - Page 12 They should be installed on the rear legs. Attaching the Sub-Frame 1.Attach the legs(17) as shown in the picture. The ends of the support struts are fastened using the same screws as the legs, as shown in the picture. TS250SL...
- Page 13 3-5mm of the riving knife. Re- install the table access plate. The guards locating pin should be positioned through the hole machined in the top edge of the riving knife. Secure using the thumb screw, do not over tighten. crew, do not over tighten. TS250SL...
- Page 14 Check that when the blade is fully lowered, the blade guard is in contact with the table top. Note: The top blade guard is equipped with a dust extraction port . TS250SL...
- Page 15 3. Fit the outer flange washer and screw in the lock nut. Hold the drive shaft with one of the spanners on the outer flange washer whilst simultaneously tightening the lock nut (clockwise). TS250SL...
-
Page 16: Operation
If the overload safety cut-off switch is triggered: Unplug the mains lead and let the saw cool down for at least 10 minutes. TS250SL... - Page 17 Undo the locking knob (c) and set the desired angle. Tighten the locking knob again. If necessary, undo the two wing nuts (d) and move the rip fence to the side so that it does not catch on the blade, then tighten the wing nuts again. TS250SL...
-
Page 18: Maintenance And Service
Warning: Always use a.push-stick if any of your hands comes closer than 125.mm to the.saw blade during the.cutting process. Never use a.damaged push-stick, replace a.damaged stick before resuming work. TS250SL... - Page 19 Do not feed the workpiece into the blade too quickly, slow the feed rate. Adjust the riving knife, refer to the Riving knife and saw blade section above. TS250SL AIR6V AIR6V AIR6V...
-
Page 20: Lumberjack Guarantee
If a return is requested by the Authorised Dealer or 1.2.3 If asked to do so by Lumberjack or its Lumberjack, you will be provided with a Returns Authorised dealer, you return the product at Material Authorisation number which must be your own cost to Lumberjack’s or supplying... - Page 21 Lumberjack. If you include a contact number with this it will speed your claim 2.4 Please note that it is essential that the letter of claim reaches Lumberjack on the last day of this Guarantee at the latest. Late claims will not be considered.
-
Page 22: Declaration Of Conformity
Old Heath Road, Wolverhampton, WV1 2RP. Tel: 01902 450 470 Declares that the Table saw(TS250SL) Is in compliance with the regulations included in the Directives:2006/42/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by TÜV SÜD Product Service GmbH-Zerifizierstelle –... -
Page 23: Parts List
Left End cap Socket screws Left guide rail Spring washer Left scale Screws Right End cap Rear mount plate Push sticker holder Hex nut C-ring Table support block Rear Bevel shaft support Self tapping screws Locking plate TS250SL AIR6V AIR6V AIR6V... - Page 24 Flat key Extension table support rod Cross head assembly Lock nut Motor bracket Lower blade guard Inner blade flange Double nut Blade Threaded rod Outter blade flange Washer Hex bolt Hex bolt Cross head assembly Main casing TS250SL AIR6V AIR6V AIR6V...
- Page 25 Threaded spacer Left extension table Washer Right Table support bar Blade spanner a Over-load switch Blade spanner b Rip fence holder Rubber foot Rip fence slider Push sticker Leg A Extension fence Hex screws Socket screws TS250SL AIR6V AIR6V AIR6V...
-
Page 26: Parts Diagram
Parts Diagram TS250SL...
Need help?
Do you have a question about the TS250SL and is the answer not in the manual?
Questions and answers