Advertisement
2.1 Ceiling Mounting for Type I
Camera
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
Figure 2-1 Drill Template
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-2 Fix the Camera to the Ceiling
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position (0 ~ 360 .
°
°)
2).Tighten No.3 adjusting screw.
3).Loosen the No.2 adjusting screw to adjust the
tilting position (0° ~ 90°).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image (0° ~ 360°).
6).Tighten No.1 adjusting screw.
Figure 2-3 3-axis Adjustment
2.2 W
all
Mounting for Type II
/ I II
Camera
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
2
Ceiling Mounting
1
1
2
2
No.1 Screw Hole
No.2 Screw Hole
for Bracket
for Mounting
Base
1
1
2
Figure 2-4 Drill Template
3.Route the cables to the cable hole and connect
the corresponding power cable and video cable
4.Fix the camera to the wall with the supplied
screws.
Adjusting Screw
Figure 2-5 Fix the Camera to the Wall
5. Adjust the surveillance angle.
1). Loosen No.3 adjusting screw to adjust the pan
position (
0° ~ 360°)
.
2).Tighten No.3 adjusting screw.
3). Loosen No.2 adjusting screw to adjust the
tilting position(
0° ~ 90°
).
4).Tighten No.2 adjusting screw.
5). Loosen No.1 adjusting screw to adjust the
rotation position
(0° ~ 360°)
.
6).Tighten No.1 adjusting screw.
360°
90°
2
360°
1
Figure 2-6 3-axis Adjustment
2.3 Ceiling Mounting for Type IV
Camera
Steps:
1.Drill the screws holes and the cable hole on the
ceiling according to the supplied drill template.
2.Hammer the supplied plastic expansion bolt
into the screw holes.
Figure 2-7 Drill Template
3.Route the cables to the cable hole and connect
the corresponding cables.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-8 Fix the Camera to the Ceiling
5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position (0°
~ 360°
2).Tighten No.3 adjusting screw.
3).Loosen No.2 adjusting screw to adjust the
tilting position (0° ~ 90°).
3
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image (0° ~ 360°).
6).Tighten No.1 adjusting screw.
Figure 2-9 3-axis Adjustment
6.Adjust the zoom and the focus.
1).Output the image to the monitor.
2).Push forward to remove the adjusting sheet
located on the bottom of the camera. See
figure below.
3).Insert the removed adjusting sheet to zoom
slot and focus slot to adjust the zoom and the
focus.
4).Put the adjusting sheet back after the
adjustment is done.
Adjusting Sheet
Figure 2-10 Focus and Zoom Adjustment
2.4 Power Supply
).
Figure 2-11 The Powe Cable & the Video Cable
Note:
Please make sure that the power adapter is
compatible with the camera, and the standard
power supply is 12V DC.
1
90°
2
3
360°
360°
Focus
Zoom
Advertisement
