Table of Contents
Advertisement
RDV-1050 DVD Player
Resuming Playback
To Resume Playback
When the resume mode is ON
While the disc that you interrupted playback
of is still on the disc tray, press
The RDV-1050 can remember the position on
. The RDV-1050 resumes playback
29
a disc where you interrupt playback and re-
from the position where playback was inter-
sume playback from that position later. There
rupted. The TV screen shows RESUME PLAY.
are three resume modes; ON, OFF and DISC
RESUME. The mode is set at the factory to ON.
To play back from the beginning of the disc
You can select the mode using the Preference
■ (STOP)
10
settings. See the Selecting Preference section.
.
29
When the Resume Mode is ON
When the resume mode is DISC
RESUME
During playback if you press ■ (STOP)
10
the RDV-1050 stops playback and remembers
Press the OPN/CLS button
the position where playback was interrupted.
panel or the OPEN/CLOSE button
The TV screen shows RESUME STOP and the
remote control to open the disc tray and in-
display window shows [– – – – RESUME] (for
sert a disc for which the RDV-1050 has stored
DVD Audio or Video discs) [– – RESUME] (for
an interrupted position. The TV screen shows
SVCD/Video CD discs). The remembered po-
RESUME STOP.
sition is not lost if the RDV-1050 is turned off.
Press
(PLAY)
When you turn off the RDV-1050 after set-
RESUME PLAY and the RDV-1050 resumes
ting the resume function, simply press
(PLAY)
playback from the position where playback
. The RDV-1050 is turned on, and play-
was interrupted.
29
back starts from the interrupted position. If you
To play back from the beginning, after inserting
turn on the RDV-1050 by pressing STANDBY
the disc, press ■ (STOP)
button
then press
(PLAY), playback
ing
(PLAY) to start playback.
starts from the beginning of the disc. Note that
the remembered position is cleared if you open
NOTES:
the disc tray.
If you change the RESUME setting from
DISC RESUME to OFF or ON, you cannot
When the Resume Mode is
resume playback of a disc whose "resum-
DISC RESUME
ing" position is stored. However, when you
reset RESUME to DISC RESUME, you will
When you press ■ (STOP)
the
10
then be able to resume playback of the
RDV-1050 stops playback and remembers the
disc.
interrupted position. The TV screen shows RE-
SUME STOP and the display window shows
If you interrupt the playback of a disc for
which an interrupted position has already
[– – – – RESUME] (for DVD Audio or Video
been stored, the memory will be updated
discs) [– – RESUME] (for SVCD/Video CD
with the new interrupted position.
discs). The remembered position where play-
For a double-sided DVD VIDEO disc, the
back was interrupted is not cleared if you open
RDV-1050 regards each side as a different
the disc tray or turn off the RDV-1050.
disc. Therefore, to resume playback of such
NOTE: The RDV-1050 memorizes inter-
a disc, the disc must be inserted with the
rupted positions for the last 30 discs
same side down.
played. Storing a new interrupted position
When the RDV-1050 memorizes an inter-
will erase the interrupted position stored for
rupted point for a disc, it also memorizes
the first disc.
Audio, Subtitle and Angle settings.
The RDV-1050 may not resume playback
To clear the memory
exactly from the interrupted point. In the
case of an SVCD/Video CD disc with PBC
Press ■ (STOP)
while disc play is
10
function, the RDV-1050 may resume play-
stopped.
back from a point slightly earlier or later
than the point where playback was inter-
rupted.
14
Various Speed Playback
To Rapidly Advance or
Reverse Playback
(PLAY)
During playback, press
30
on the remote control unit. You can select from
1.5 times, 5 times, 20 times and 60 times nor-
before pressing
(PLAY)
mal speed. Pressing
(PLAY)
turns the RDV-1050 to normal playback.
During playback, hold down
. Playback is advanced or reversed at 5
27
on the front
times normal speed.
on the
2
During rapid playback, the sound is muted
except when playing an Audio CD or Audio
DVD, and when playing a DVD VIDEO or
Video CD at 1.5 times normal speed. For Audio
CD discs, the sound is heard intermittently.
. The TV screen shows
29
1.5x Quick Playback With
Sound
When you select 1.5 times normal speed play-
before press-
10
back, the disc is played back with sound.
• For DVD VIDEO discs, the subtitles remain
on.
• If the sound of a DVD VIDEO disc is recorded
in Dolby Digital or DTS format, stereo lin-
ear PCM signals are output. With some DVD
VIDEO discs, the sound quality and volume
may be altered, or the sound may be out
of tune.
• To switch from rapid reverse playback to x1.5
Quick Playback, first press
29
, then press
30
To Advance a Still Picture
Frame by Frame
With disc play paused, press
. Each time you press
II
28
still picture advances to the next frame. Press
(PLAY)
to return to normal play-
29
back.
2 Press
/
32 14
desired group.
3 Press
/
27
4 Press
(PLAY)
29
The slide show starts from the specified file.
Direct Selection
or
11
1 During playback or while stopped, press
TITLE/GROUP
8
2 Press the numeric buttons
re-
29
group number.
Examples:
or
9
To select 5: press 5.
To select 23: press +10, +10, then 3.
To select 40: press +10, +10, +10, then 10.
3 Press the numeric buttons to specify a file
number. The RDV-1050 starts slide show
playback from the specified file. If you do
not specify a file, the RDV-1050 starts slide
show playback from the first file in the group.
Slide Show Repeat Function
In the slide show mode, you can repeat play-
back of JPEG files in a group or on the disc.
1 While the JPEG CONTROL display is shown,
press REPEAT
. Pressing REPEAT switches
3
the repeat mode. When the repeat mode
is turned on, the
display window.
The selected repeat mode is shown on the
JPEG CONTROL display.
REPEAT ALL: All files on the disc are re-
peated.
REPEAT GROUP: All files in the current
group are repeated.
(PLAY)
No indication: The repeat mode is off.
once.
2 Press
(PLAY)
29
back.
To stop repeat playback Press ■ (STOP)
The repeat mode remains active.
To quit repeat playback Press ■ (STOP) or
I I
(PAUSE)
MENU
while the JPEG CONTROL display
31
(PAUSE), the
is shown, then press REPEAT until the repeat
mode indication goes off.
NOTE: You can change the repeat mode us-
ing ON SCREEN
34
unit. Press ON SCREEN, and the repeat mode
selection window appears on the TV screen.
Press then
/
32 14
repeat mode, and finally press ENTER
make the selected repeat mode active.
27
to move the bar to a
Selecting Preferences
to select a file.
9
This section tells you how to change the Pref-
.
erence Settings. Read this section when you
want to connect the RDV-1050 to a wide-vi-
sion TV set, or when you want to otherwise
change the settings according to your pref-
erences and viewing environment.
.
About the Preference Display
to specify a
4
The Preference display consists of the LAN-
GUAGE, PICTURE, AUDIO SPK.SETTING and
OTHERS setting displays.
Make sure that the TV - DVD switch
the remote control unit is set to "DVD" when
using the
/ / /
32 14 13 33
TV/VIDEO - CANCEL
buttons for con-
23
trolling the RDV-1050.
LANGUAGE
indicator lights in the
PICTURE
AUDIO
to start repeat play-
.
10
SPK.SETTING
on the remote control
to select the desired
to
35
English
OTHERS
How to Set Preferences
1 Press CHOICE
. One of the preference
15
on-screen displays appears on the TV
screen. There are five icons at the top right
1
on
of the on-screen display.
: LANGUAGE menu
and
: PICTURE menu
: AUDIO menu
: SPEAKER SETTING menu
: OTHERS menu
2 Press /
to select one of the icons.
13 33
The corresponding display appears on the
TV screen.
3 Press
/
to select the item you
32 14
want to edit. The color of the selected item
changes.
4 Press ENTER
. A pull-down menu ap-
35
pears over the selected item.
5 Press
/
to select from the options then
press ENTER. The selected option is set.
See the following sections for details about each
setting.
To turn off the preference display press
CHOICE.
— continued
Advertisement
Table of Contents
