Front And Rear Panels; Mixer Section - Roland VXpanded VS-880 Owner's Manual

Front and rear panels

Mixer section

INPUT SENS
1 2 3 4
PEAK PEAK PEAK PEAK
10 10 10 10
4 50 dBm 4 50 dBm 4 50 dBm 4 50 dBm
PAN PAN PAN PAN PAN
C C C C C
L R L R L R L R L R
CH EDIT CH EDIT CH EDIT CH EDIT CH EDIT
Input BUSS
Input BUSS V.Track EQ Low EQ Mid EQ Hi
V.Track
EQ
BUSS Send
AUX Send
Channel Link
SEL SEL SEL SEL SEL
EFFECT - 1
- 2
SOURCE
STATUS STATUS STATUS STATUS STATUS
REC
PLAY
MUTE
1 2 3 4 5
a b
BUSS AUX BUSS AUX BUSS
(dB)
6
4
0
4
8
12
18
24
36
1. PEAK indicators
These indicators allow you to avoid distortion of the sound
being input at the input jacks (1Ð4). The peak indicators will
light red when the signal reaches -6 dB before clipping
level. Adjust the input sensitivity so that the peak indicators
do not light.
2. INPUT SENS (input sensitivity) knobs
These knobs adjust the sensitivity of the input jacks (1Ð4).
Rotate a knob fully right for mic level (-50 dBm), and fully
left for line level (+4 dBm).
3. PAN knobs
These knobs adjust the pan (location in the stereo output) of
each channel.
4. CH EDIT / SEL (channel edit/select) buttons
Use these buttons when you wish to make settings for a
mixer channel. The names of the parameter groups that can
be set for each channel are printed below CH EDIT. To
directly specify a particular group, you can hold down
[SHIFT] and press the button for that group name.
When editing a song, use these buttons to select tracks for
editing.
5. STATUS buttons
These buttons switch the status of each channel. The current
status is shown by the button indicator.
SOURCE (orange): The input source assigned to the
channel is being output.
REC (blinking red): Recording is selected for the track
assigned to the channel.
PLAY (green): The track assigned to the channel
will playback.
MUTE (dark): The channel is muted (silent).
6. Channel faders
Use these faders to adjust the volume level of each channel.
MIXER MODE PHONES
SELECT
INPUT TRACK
INPUT MIX
TRACK MIX
0 10
PAN PAN PAN AUX SEND
C C C
0
L R L R L R 6 dB
CH EDIT CH EDIT CH EDIT EDIT
EFFECT - 1 EFFECT - 2
Aux Send SOLO
Master Out
SEL SEL SEL
AUX SEND
EFFECT - 1
- 2
STATUS STATUS STATUS
6 7 8 MASTER
c d
AUX BUSS AUX
(dB)
6
4
0
4
8
12
18
24
36
7. SELECT button
This button switches the operating mode of the mixer. The
current mixer mode is shown by the indicators located at
the right of the button. Each time you press the button, you
will alternate between INPUT MIX mode and TRACK MIX
mode. To change from INPUT
MIX mode / TRACK MIX mode, hold down [SHIFT] and
press the button. Use the same operation to move in the
other direction.
INPUT TRACK mode
INPUT MIX mode
TRACK MIX mode
8. PHONES knob
This knob adjusts the volume of the headphones.
9. AUX SEND knob
This knob adjusts the output level of the AUX SEND jacks.
10. EDIT/SOLO button
Press this button to make settings for the master section of
the mixer.
To use the Solo function to monitor only a specific channel,
hold [SHIFT] while you press the button.
11. Master fader
Use this fader to adjust the overall output level.
TRACK mode to INPUT
13