Program Change - Roland XV-88 Owner's Manual

MIDI Implementation
Vibrato Delay (Controller number 78)
Status 2nd byte
BnH 4EH
n = MIDI channel number:
vv = Vibrato Delay value (relative change):
* The vibrato delay will change in GM mode.
General Purpose Controller 5 (Controller number 80)
Status 2nd byte
BnH 50H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Level parameter (PATCH/TVA/TVA) of Tone 1 will change.
General Purpose Controller 6 (Controller number 81)
Status 2nd byte
BnH 51H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Level parameter (PATCH/TVA/TVA) of Tone 2 will change.
General Purpose Controller 7 (Controller number 82)
Status 2nd byte
BnH 52H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Level parameter (PATCH/TVA/TVA) of Tone 3 will change.
General Purpose Controller 8 (Controller number 83)
Status 2nd byte
BnH 53H
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Level parameter (PATCH/TVA/TVA) of Tone 4 will change.
Portamento control (Controller number 84)
Status 2nd byte
BnH 54H
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = source note number: 00H - 7FH (0 - 127)
* A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number,
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.
Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte
BnH 5BH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Reverb Send Level: 00H - 7FH (0 - 127)
* In Performance mode the Reverb parameter (PERFORM/EFFECTS/OUTPUT) will
change.
Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte
BnH 5DH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Chorus Send Level: 00H - 7FH (0 - 127)
* In Performance mode the Chorus parameter (PERFORM/EFFECTS/OUTPUT) will
change.
272
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
kkH
3rd byte
vvH
3rd byte
vvH
RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then
Data Entry (Controller numbers 6 and 38) should be sent to set the value. Once RPN
messages are received, Data Entry messages that is received at the same MIDI channel after
that are recognized as changing toward the value of the RPN messages. In order not to
make any mistakes, transmitting RPN Null is recommended after setting parameters you
need.
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB
00H, 00H mmH, llH
00H, 01H mmH, llH
00H, 02H mmH, llH
00H, 05H mmH, llH
7FH, 7FH ---, ---

Program Change

Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - 16)
pp = Program number: 00H - 7FH (prog.1 - prog.128)
* Not received in Performance mode when the Program Change parameter (PERFORM/
MIDI/RxSWITCH) is OFF.
Channel Pressure
Status 2nd byte
DnH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Channel Pressure: 00H - 7FH (0 - 127)
* Not received in Performance mode when the Caf parameter (PERFORM/MIDI/
RxSWITCH) is OFF.
Pitch Bend Change
Status 2nd byte
EnH llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
* In Performance mode, the BendRng parameter
(PERFORM/PART/PITCH) will change.
Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
* In Performance mode, the Fine parameter
(PERFORM/PART/PITCH) will change.
Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* In Performance mode, the Coarse parameter
(PERFORM/PART/PITCH) will change.
Modularion Depth Range
mm: 00 00H - 06 00H
(0 - 16384 x 600 / 16384 cent)
* Not received in Performance mode or Patch
mode.
RPN null
RPN and NRPN will be set as "unspecified."
Once this setting has been made, subsequent
Parameter values that were previously set will
not change.
mm, ll: ignored
3rd byte
mmH