1. Manuals
  2. Brands
  3. ICP Electronics Manuals
  4. Motherboard
  5. JUKI-6752
  6. Manual

ICP Electronics JUKI-6752 Manual

Low power pentium mmx 266 with crt/lcd, ethernet single board computer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
JUKI-6752 Ver 1.0
Low Power Pentium® MMX 266
with CRT/LCD,Ethernet
Single Board Computer
Copyright Notice
©Copyright 2000 by ICP Electronics Inc. All Rights Reserved. Manual first edition
JUL..01, 2000.
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the
part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic,
or other means in any form without prior written permission of the manufacturer.
Trademarks
JUKI-6752 is a registered trademark of ICP Electronics Inc. IBM PC is a registered
trademark of International Business Machines Corporation. Intel is a registered
trademark of Intel Corporation. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks of
www.iei.com.tw
their respective companies.
I
Contents
Introduction.................................................................... 1
1.1 Specifications : .................................................................................... 2
1.2 What You Have................................................................................... 3
Installation ..................................................................... 4
2.1 JUKI-6752 Layout.............................................................................. 4
2.2 Unpacking ........................................................................................... 6
2.3 Compact Flash Setting (JP1) ............................................................... 7
2.4 Clear CMOS Setup (JP2) .................................................................... 7
2.5 LCD Voltage and Clock setting (JP4)................................................ 7
2.6 COM2 RS-232, RS-422 or RS-485 Setting (JP5) ............................... 8
2.7 COM2 PIN8 Setting (JP6)................................................................... 8
Connection .................................................................... 9
3.1 IDE Disk Drive Connector(CN1)........................................................ 9
3.2 CompactFlash Connector -- TYPE II(CN2)...................................... 10
3.3 PC/104 Connection Bus(CN3,CN4) ................................................. 11
3.4 USB Port Connector(CN5)................................................................ 12
3.5 VGA Connector(CN6) ...................................................................... 13
3.6 LCD Interface Connector(CN7) ........................................................ 13
3.7 LAN RJ45 Connector (CN9)............................................................. 15
II

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JUKI-6752 and is the answer not in the manual?

Questions and answers

Related Manuals for ICP Electronics JUKI-6752

Summary of Contents for ICP Electronics JUKI-6752

  • Page 1: Table Of Contents

    3.2 CompactFlash Connector -- TYPE II(CN2)........10 Trademarks 3.3 PC/104 Connection Bus(CN3,CN4) ..........11 JUKI-6752 is a registered trademark of ICP Electronics Inc. IBM PC is a registered 3.4 USB Port Connector(CN5)..............12 trademark of International Business Machines Corporation. Intel is a registered 3.5 VGA Connector(CN6) ..............
  • Page 2 3.8 Serial Ports(CN10,CN11) ..............15 B.2 DMA channel assignments ............... 35 3.9 IrDA Infrared Interface Port (CN12-1~5) ......... 16 B.3 Interrupt assignments................ 36 3.10 Reset Switch (CN12-6,7) ..............17 B.4 1 MB memory map ................. 36 3.11 External / Internal Speaker (CN12-8~11) ........17 3.12 Hard Drive LED (CN12-13,14) ............

  • Page 3: Introduction

    Welcome to the JUKI-6752 Pentium® with VGA Single Board • PCI VGA : C&T 69000 with 2MB SDRAM built-in Chipset Computer. The JUKI-6752 board is an ISA form factor board, which comes equipped with high performance and low power Pentium® Resolution : 1280x1024,256 color,60Hz...

  • Page 4: What You Have

    USB port : Support two USB ports for future expansion, USB 1.1 compliant. • Watch-dog timer This chapter describes how to install the JUKI-6752. At first, the • CompactFlash disk : The CompactFlash Storage Card also runs in True layout of JUKI-6752 is shown, and the unpacking information that IDE Mode that is compatible with an IDE disk drive.

  • Page 5: Unpacking

    IC's to make sure that they are properly seated. Do this only with the board place on a firm flat surface. Note : DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED. You are now ready to install your JUKI-6752 Single Board Computer.

  • Page 6: Compact Flash Setting (Jp1)

    2.3 Compact Flash Setting (JP1) 2.6 COM2 RS-232, RS-422 or RS-485 Setting (JP5) Set the operating mode of CompactFlash disk. The COM2 (CN11) can be set to RS-232 or RS-422/485 for industrial field site application. Moreover when this port was set to the RS-485 •...

  • Page 7: Connection

    DATA 13 DATA 6 DATA 14 You can attach two IDE( Integrated Device Electronics) hard disk DATA 7 DATA 15 drives to the JUKI-6752 IDE controller(Primary). The IDE supports HDC_CS0# HDC_CS1 Ultra DMA/33 interface . GROUND IOR# • CN1: IDE Interface Connector (2.0MM) IOW# PIN NO.

  • Page 8: Pc/104 Connection Bus(Cn3,Cn4)

    SA13 DRQ1 3.4 USB Port Connector(CN5) SA12 REFRESH# SA11 SYSCLK The JUKI-6752 built in two USB ports for the future new I/O bus SA10 IRQ7 expansion. It is USB 1.1 compliant IRQ5 • CN5: USB 0 & USB 1 IRQ4...

  • Page 9: Vga Connector(Cn6)

    • CN7: LCD Interface Connector – support up to 36 bit LCD. For 3.5 VGA Connector(CN6) better display quality, the length of LCD cable should be shorter The JUKI-6752 built in a 15-pin VGA connector that accepts the CRT than 45 cm. monitor.

  • Page 10: Lan Rj45 Connector (Cn9)

    3.9 IrDA Infrared Interface Port (CN12-1~5) GROUND (GND) DATA SET READY (DSR) The JUKI-6752 built in a IrDA port which support Serial Infrared (SIR) . REQUEST TO SEND (RTS) When use the IrDA port have to set SIR model in the BIOS’s...

  • Page 11: Reset Switch (Cn12-6,7)

    3.10 Reset Switch (CN12-6,7) 3.13 Parallel Port(CN13) This port is usually connected to a printer, The JUKI-6752 includes an You can connect an external switch to reset your computer easily. on-board parallel port, accessed through a 26-pin flat-cable connector •CN12(PIN 6,7): Reset Switch connector CN13.

  • Page 12: Keyboard Connector(Cn15,Cn16)

    GROUND WRITE GATE# 3.16 External Power Connector(CN18) GROUND TRACK 0# GROUND WRITE PROTECT# The JUKI-6752 has an on-board external power connector CN18. You GROUND READ DATA# can connect power directly to the CPU board. GROUND SIDE 1 SELECT# GROUND DISK CHANGE# •CN18: External Power Connector...

  • Page 13: Award Bios Setup

    AWARD BIOS Setup The JUKI-6752 uses the AWARD PCI/ISA BIOS for system configuration. The AWARD BIOS setup program is designed to provide maximum flexibility in configuring the system by offering various options which may be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features.

  • Page 14: Standard Cmos Setup

    CRT: Auxiliary monitor. When you want to use CRT only, please 4.2 Standard CMOS Setup select this option. The CRT will have good screen. The Standard CMOS Setup is used for basic hardware system Both: Display on both device. When you want to use both display, configuration.

  • Page 15: Bios Features Setup

    This BIOS Features Setup is designed for customer‘s tuning best could be running un-stable. performance of the JUKI-6752 board. As for normal operation customers don‘t have to change any default setting. The default setting is pre-set for most reliable operation.

  • Page 16: Integrated Peripherals

    Memory Hole at 15M-16M : Enable or Disable 4.5 Integrated Peripherals This setting reserve 15MB to 16MB memory address space for ISA This setup is almost working for Multi-I/O Chip(W83977TF-AW ). expansion cards that specifically require this setting. Memory from These options are used to change the ChipSet‘s registers.

  • Page 17: Power Management Setup

    Under Windows 3.x and Windows 95,you have to install Windows 4.6 Power Management Setup with APM feature. A battery and power cord icon labeled “Power” Power Management Setup help user handles the JUKI-6752 Will appear in the “Control Panel” board‘s “green” function. The features could shut down the video display and hard disk to save energy for example.

  • Page 18: Pnp/Pci Configuration

    Appendix A. Watch-Dog Timer 4.7 PNP/PCI Configuration The PNP/PCI Configuration help user handles the JUKI-6752 board‘s “PCI” function. All PCI bus slots on the system use INTA#,thus all installed PCI slots must be set to this value.. The WatchDog Timer is a device to ensure that standalone systems can always recover from abnormal conditions that cause the system to crash.

  • Page 19: Appendix B. I/O Address Map

    Example assembly program: Appendix B. I/O Address Map TIMER_PORT = 443H TIMER_START = 443H B.1 System I/O Address Map TIMER_STOP = 843H I/O Address Map Description ;;INITIAL TIMER COUNTER 000-01F DMA Controller #1 020-021 Interrupt Controller # 1, Master MOV DX, TIMER_PORT 022-023 Chipset address 040-05F...

  • Page 20: Dma Channel Assignments

    B.2 DMA channel assignments B.3 Interrupt assignments Channel Interrupt # Interrupt source Function Parity error detected Available IRQ 0 System timer Audio* IRQ 1 Keyboard Floppy disk (8-bit transfer) IRQ 2 Interrupt from controller 2 (cascade) Parallel** IRQ 8 Real-time clock Cascade for DMA controller 1 IRQ 9 Available...

Table of Contents