Salus RT510 Quickmanual Installation

Model: RT510 / RT510RF / RT510TX / RT510BC / RXRT510
Quick Guide Installation
RT510 and RT510RF Quick Guide
Introduction
The RT510 thermostat will switch your heating system on or off, as needed, in accordance
with the temperature set by you. The RT510 series includes the following products:
• RT510 for wired applications
• RT510RF (RT510TX + RXRT510) for wireless applications
• RT510TX for wireless application, using 5 x 5 receiver
• RXRT510 for wireless application using 5 x 5 transmitter
• RT510BC for wireless application
Go to www.salus-manuals.com for the full PDF version of the manual.
Product Compliance
EU Directives: 2014/30/EU, 2014/35/EU, 2014/53/EU and 2011/65/EU. Please check
www.saluslegal.com for the full information.
Safety Information
Use in accordance with the EU and national regulations.
For indoor use only.
Keep your device completely dry.
This product must be installed by a competent person and in accordance with all the
EU and national regulations.
Always isolate the AC Mains supply before installing or working
on any components that require 230 VAC 50Hz supply.
Installation
RT510 Thermostat
+Hr
Insert the batteries and
SELECT SET
wire up the device.
Terminal Description Backplate
1 (COM) Common Terminal
Switched Live OFF
2 (NC)
3 (NO) Switched Live ON
Installation
RT510RF (RT510TX+RXRT510)Thermostat and Receiver
+Hr
TEST / PAIRING
SELECT SET
Insert the batteries and wire up the receiver. After that please switch the
receiver ON. If you are using the RT510RF pack, the pairing between the
thermostat and the receiver is already done.
Terminal Description
NO Switch Terminal
COM Common Switch Terminal
L Mains Live (230VAC)
N Mains Neutral
RT510BC (RT510TX+Boiler Controller)
+Hr
TEST / PAIRING
SELECT SET
Insert the batteries and wire up the boiler controller. If you are using the
N L 1 2 3 4
RT510BC pack, the pairing between the thermostat and the receiver is
already done.
Terminal Description
1 (N) Mains Neutral
N L 1 2 3 4 N L 1 2 3 4 5 6
2 (L) Mains Live
N L 1 2 3 N L 1 2 3 N L 1 2 3 N L 1 2 3
3 (COM)
Common Switch Terminal
N L 1 2 3 N L 1 2 3
N L 1 2 3 4 N L 1 2 3
4 (NO) Switch Terminal
N L 1 2 3
Boiler internal connections
RESET
Dip Switch Settings
The DIP switches are found on the rear of
your thermostat and can be used to change
the span (temperature accuracy) of your
thermostat from the default +/-0.5°C to
+/-0.25°C and the programmes 5-2 or 24h.
Changing DIP Switch 2 may cause your boiler
to operate more frequently. The DIP switches
are located on the back of the thermostat.
Button Functions RT510 and RT510TX
RT510
+Hr
RESET
SELECT SET
ON OFF
AUTO MANUAL
Key Function
Receiver Terminals
1. Press once to activate Frost Mode
2. Press for 3 seconds in order to activate Holiday Mode.
+Hr Press once to activate/deactivate Boost function
NO COM L N Press once to enter/exit Permanent Override function.
Increase button
Decrease button
Select the clock or programme settings
SELECT
Press to confirm your settings
SET
1. Press once to enter in Test Mode for RT510RF
2. Press for 3 seconds to enter/exit Pairing Mode for RT510RF
3. Press once to return to Factory Settings for the RT510
+ +
Press the buttons for 3 seconds to enter Installer Mode
SELECT
+
Press the buttons for 3 seconds to enter Clock Settings
N L 1 2 3 4 5 6
SET
Rear of controller
Installer Mode
4 3 2 1
3 Sec
N L 1 2 3 4 N L 1 2 3 4 5 6
4 4 4 4 N L 1 2 3 N L 1 2 3 N L 1 2 3 N L 1 2 3 4 5 6 4 5 6 4 5 6 4 5 6
+Hr
4 4 N L 1 2 3 N L 1 2 3 4 5 6 4 5 6
4 5 6
4 N L 1 2 3 4 5 6
RESET
SELECT SET
3 Sec 3 Sec
Press the three buttons
together for 3 seconds.
dxx Function Parameter
ON
24H +/-0.25
Temperature display
d01 0.1 or 0.5°C
increments
d02 Temperature offset +/-3.0°C
5-2 +/-0.5
d03 Frost setpoint 5.0-17.0°C Set the Frost Point temperature 5.0°C
2
1
Pairing the RT510TX with the Receiver/Boiler Controller
RT510TX
If you are using the RT510RF or RT510BC pack, the pairing between
the thermostat and the receiver/boiler controller is already done.
If you bought an RT510TX and RXRT510 separately then pair as follows.
+Hr
Please make sure that the Receiver/Boiler Controller is set on Auto.
Begin the pairing process
TEST / PAIRING
SELECT SET
+Hr
3 Sec
SELECT SET
End the pairing process
+Hr
3 Sec
SELECT SET
Test the pairing process
+Hr
SELECT SET
+Hr
SELECT SET
If you bought an RXRT510 or RT510TX and intend pairing with other
devices in the 5x5 range, please refer to the Receiver Units manual, or the
relevant manuals available at www.salus-manuals.com
+Hr
Button Description for RXRT510 Receiver
Button Function
RESET
SELECT SET
ON The receiver is enabled, ready for use.
OFF The receiver is disabled, will not function.
AUTO The receiver will switch on and off automatically,
as operated by the thermostat.
MANUAL Providing ON is selected,the receiver will switch
on continuously, overriding the thermostat.
Button Description for RXBC605 Boiler Controller
Description Default
value
Button Function
Select temperature display
SYNC The boiler controller will be syncronised with the
0.5°C
increments
thermostat.
Calibrate your thermostat AUTO The receiver will switch on and off automatically,
0.0°C
temperature
as operated by the thermostat.
MANUAL Select in the event of thermostat failure to switch
boiler on continuously, overriding the thermostat.
+Hr
TEST / PAIRING TEST / PAIRING
SELECT SET
Wait 9 minutes for the timeout
process to be complete.
+Hr
TEST / PAIRING TEST / PAIRING
SELECT SET
ON OFF
AUTO MANUAL
TEST / PAIRING
ON OFF
AUTO MANUAL
TEST / PAIRING
ON OFF
AUTO MANUAL