Salus RT510 Installation Manual

Model: RT510
(Wired, electronic thermostat - programmable)
RT510RF
(Wireless, electronic thermostat - programmable)
Installation Manual
DISTRIBUTOR OF SALUS CONTROLS: Importer:
QL CONTROLS Sp. z o.o., Sp. k. SALUS Controls plc
Rolna 4, Salus House, Dodworth Business Park
43-262 Kobielice, Whinby Road, Barnsley S75 3SP,
Poland United Kingdom
www.salus-controls.eu
SALUS Controls is a member of the Computime Group.
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to
change specification, design and materials of products listed in this brochure without prior notice.

Introduction

RT510 / RT510RF is a programmable room thermostat used to control room temperature. Device
launching heating system by shorting terminal blocks, simultaneously informing the action and
showing this information on the LCD display. Extended features allows us to use various operating modes
- automatic (time schedules), manual, frost protection or holiday. Before use please read this manual
carefully. Use only AA 1.5 V alkaline batteries in the thermostat. Place the batteries into the battery slot
located under the cover. Do not use rechargeable batteries.

Product compliance

Directives: EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU.
Full information is available on the website www.saluslegal.com

Safety Information

Use in accordance to national and EU regulations. Use the device as intended, keeping it in dry condition.
Product for indoor use only. Installation must be carried out by a qualified person in accordance to national
and EU regulations.

Technical specification

RT510 Thermostat RT510TX Thermostat
Thermostat supply 2 x AA alkaline batteries 2 x AA alkaline batteries
Thermostat rating max 3 (1) A -
Voltage free
Outputs NO / COM / NC -
terminals
Temperature range 5 - 35°C 5 - 35°C
Temperature accuracy 0.1°C or 0.5°C 0.1°C or 0.5°C
Hysteresis ±0.25°C or ±0.5°C ±0.25°C or ±0.5°C
Radio frequency - 868 MHz
Dimension [mm] 120x96x27 120x96x27
RXRT510 Receiver
Receiver supply 230 V AC
Receiver rating max 16 (5) A
Outputs Voltage free NO / COM terminals
Radio frequency 868 MHz
Dimension [mm] 96x96x27

Button functions

RT510/RT510TX Thermostat RXRT510 Receiver
3
1 4
2 5
6
8
1. Boost function 6. When in Manual Mode,
2. Manual Mode ON will turn the boiler on.
7. When in Manual Mode,
3. Frost protection / Holiday Mode
OFF will turn the boiler off.
4. Increase button
8. Receiver operates in automatic mode
5. Decrease button
according to the thermostat
9. Receiver output is controlled
by the On/Off slide switch.

LCD Icon description

1. Day of the week
2. Program number
15 14 13 12
11
3. Program indicator
1
10
4. Settings
9
5. Temperature measured / set
8
6. Boost function
7
7. Low battery status
2
8. Wireless connection with the receiver
AC 230 V
L
3 4 5 6
9. Heating Mode On
10. Manual Mode On
11. Holiday Mode On
12. Frost Protection Mode On
L
COM
13. Temperature unit
14. AM / PM
15. Clock
NO
N
N
RT510 Terminals description
Terminal Description
1 - COM Common Terminal
2 - NC Switched Live OFF
3 - NO Switched Live ON
RXRT510 Receiver terminals description
Terminal Description
NO Switch Terminal
COM Common Switch Terminal
NO COM L N
L, N Supply (230 V AC)

DIP Switch Settings

ON
The DIP switches are found on the rear of your thermostat.
24H
+/-0.25°C
The DIP switch number 1 is used to change the schedule mode: 5-2
mode (business days + weekend) or for each day separately mode.
DIP switch number 2 is used to change the span (temperature
accuracy) of your thermostat from the default ±0.5°C to ±0.25°C.
5-2 +/-0.5°C
This may cause your boiler to operate more frequently.
1

RT510 Wiring diagram

AC 230 V
L
7
9
N
RT510RF Wiring diagram
Note: If you are using the RT510RF pack, the pairing between the thermostat and the receiver is already done.
AC 230 V
L
L
COM
N
N
AC 230 V
L
L
N
N
AC 230 V

Setting the time

L
1 2
MAX
3 (1) A
TEST / PAIRING
SELECT SET
Press
3 sec 3 sec
M
or
Press the buttons SELECT and SET
together for 3 sec.
SELECT SET
N
3 4
SELECT SET TEST / PAIRING
TEST / PAIRING
SELECT SET
Press
Press SELECT to confirm.
SET
SELECT
5 6
TEST / PAIRING
SELECT SET
TEST / PAIRING
2 SELECT SET
Press
Press SELECT to confirm.
SELECT SET
N
N
7
AC 230 V
L
MAX
3 (1) A
SELECT SET
MAX
3 (1) A
Press SELECT to confirm.
SELECT
9
M
or
SELECT
OR or M
N
SELECT SET
Press SET to confirm.

Programming - automatic mode

In this mode, user can set the schedules for thermostat (temperature setpoints for specific periods of
time). To do this, firstly choose programming mode: "5-2" (business days + weekend) or "24h" (each
day separately) using DIP switch no. 1. Programmed schedules should use all time periods.
NO 1
SELECT SET
AC 230 V
L
COM Press the SET button to start programming.
SELECT
MAX
16 (5) A
3
SELECT
NO MAX
3 (1) A
M
OR or
SELECT SET
or M
N
Press SELECT to confirm.
SELECT
5
SELECT
TEST / PAIRING
SELECT SET SELECT SET
or to select the hour format.
Press SELECT to confirm.
TEST / PAIRING
SELECT
7
SELECT
SELECT SET
TEST / PAIRING
SELECT SET
or to set the hour.
Press SELECT to confirm.
TEST / PAIRING
9
SELECT
SELECT SET
TEST / PAIRING
SELECT SET
or to set the minutes.
Press SELECT to confirm.
TEST / PAIRING
8
TEST / PAIRING SELECT SET TEST / PAIRING
Press or to set day of the week.
SET TEST / PAIRING
10
TEST / PAIRING
SET
TEST / PAIRING SELECT SET TEST / PAIRING
Thermostat will return to the main screen.
AC 230 V
L
L COM
MAX
16 (5) A
N NO
2
M
or
N
TEST / PAIRING SELECT SET TEST / PAIRING
Use the or button to select day / days
from which you want to start programming.
SET TEST / PAIRING
4
SET TEST / PAIRING
TEST / PAIRING TEST / PAIRING
SELECT SET
Use the or button to set the hour
to start the program #1.
TEST / PAIRING
SET
6
SET TEST / PAIRING
TEST / PAIRING SELECT SET TEST / PAIRING
Use the or button to set the minutes
to start the program #1.
TEST / PAIRING
SET
8
TEST / PAIRING
SET
TEST / PAIRING SELECT SET TEST / PAIRING
Use the or button
to set the temperature for program #1.
SELECT SET TEST / PAIRING
10
TEST / PAIRING
SET
TEST / PAIRING SELECT SET TEST / PAIRING
Follow steps 4-9,
to define programs 2-6.
Press SET button to end programming.