Deep Sea Electronics Plc DSE4510 Installation Instructions And Use

Configuration Parameters – Module (Page 1)
101 Contrast 0 (%) 117 Use Module RPM
102 Fast Loading Enabled On (1), Off (0) 118 Use Module Charge Alt
103 All Warnings Latched On (1), Off (0) 119 Disable CAN Speed Control
104 Lamp Test At Startup On (1), Off (0) 120 CT Position
105 Power Save Mode Enable On (1), Off (0) 121 Generator Voltage Display
106 Deep Sleep Mode Enable On (1), Off (0) 122 Mains Voltage Display
107 Protected Start Enable On (1), Off (0) 123 Generator Frequency Display On (1), Off (0)
108 Event Log Display Format On (1), Off (0) 124 Mains Frequency Display
109 Power Up Mode 0 (Power Up Mode) 125 Current Display
110 DTC String Enable On (1), Off (0) 126 kW Display
111 RESERVED 127 kVAr Display
Pin Protected
112 On (1), Off (0) 128 kVA Display
Maintenance Reset
113 Stop Button Cooldown On (1), Off (0) 129 pf Display
114 Use Module Oil Pressure On (1), Off (0) 130 kWh Display
115 Use Module Coolant Temp On (1), Off (0) 131 kVArh Display
116 Use Module Engine Hours On (1), Off (0) 132 kVAh Display
Configuration Parameters – CAN Application (Page 2)
201 CAN Alternative Engine Speed On (1), Off (0) 203 CAN ECU Data Fail Action
202 CAN ECU Data Fail Enable On (1), Off (0) 204 CAN ECU Data Fail Delay
Configuration Parameters – Digital Inputs (Page 3)
301 Digital Input A Source
302 Digital Input A Polarity
303 Digital Input A Action (If Source = User Config)
304 Digital Input A Arming (If Source = User Config)
305 Digital Input A Activation Delay (If Source = User Config)
306 Digital Input B Source
307 Digital Input B Polarity
308 Digital Input B Action (If Source = User Config)
309 Digital Input B Arming (If Source = User Config)
310 Digital Input B Activation Delay (If Source = User Config)
311 Digital Input C Source
312 Digital Input C Polarity
313 Digital Input C Action (If Source = User Config)
314 Digital Input C Arming (If Source = User Config)
315 Digital Input C Activation Delay (If Source = User Config)
316 Digital Input D Source
317 Digital Input D Polarity
318 Digital Input D Action (If Source = User Config)
319 Digital Input D Arming (If Source = User Config)
320 Digital Input D Activation Delay (If Source = User Config)
321-330 RESERVED
331 Analogue Input A (Set As Digital) Source
332 Analogue Input A (Set As Digital) Polarity
333 Analogue Input A (Set As Digital) Action (If Source = User Config)
334 Analogue Input A (Set As Digital) Arming (If Source = User Config)
335 Analogue Input A (Set As Digital) Activation Delay (If Source = User Config)
336 Analogue Input B (Set As Digital) Source
337 Analogue Input B (Set As Digital) Polarity
338 Analogue Input B (Set As Digital) Action (If Source = User Config)
339 Analogue Input B (Set As Digital) Arming (If Source = User Config)
340 Analogue Input B (Set As Digital) Activation Delay (If Source = User Config)
341 Analogue Input C (Set As Digital) Source
342 Analogue Input C (Set As Digital) Polarity
343 Analogue Input C (Set As Digital) Action (If Source = User Config)
344 Analogue Input C (Set As Digital) Arming (If Source = User Config)
345 Analogue Input C (Set As Digital) Activation Delay (If Source = User Config)
Configuration Parameters – Outputs (Page 4)
401 Digital Output A Source 0 (Output Source) 407 Digital Output D Source
402 Digital Output A Polarity 0 (Output Polarity) 408 Digital Output D Polarity
403 Digital Output B Source 0 (Output Source) 409 Digital Output E Source
404 Digital Output B Polarity 0 (Output Polarity) 410 Digital Output E Polarity
405 Digital Output C Source 0 (Output Source) 411 Digital Output F Source
406 Digital Output C Polarity 0 (Output Polarity) 412 Digital Output F Polarity
Pressure Sensor List Temperature Senor List
Index Type Index Type
0 Not used 0 Not Used
1 Dig Closed for Alarm 1 Dig Closed for Alarm
2 Dig Open for Alarm 2 Dig Open for Alarm
3 VDO 5 Bar 3 VDO 120 °C
4 VDO 10 Bar 4 Datcon High
5 Datcon 5 Bar 5 Datcon Low
6 Datcon 10 Bar 6 Murphy
7 Datcon 7 Bar 7 Cummins
8 Murphy 7 Bar 8 PT100
9 CMB812 9 Veglia
10 Veglia 10 Beru
11 User Defined 11 User Defined
Configuration Parameters – Timers (Page 5)
On (1), Off (0) 501 Mains Transient Delay
On (1), Off (0) 502 Start Delay
On (1), Off (0) 503 Preheat Timer
Gen (0), Load(1) 504 Crank Time
On (1), Off (0) 505 Crank Rest Time
On (1), Off (0) 506 Smoke Limiting
507 Smoke Limiting Off
On (1), Off (0) 508 Safety On Delay
On (1), Off (0) 509 Warm Up Time
On (1), Off (0)
Configuration Parameters – Generator (Page 6)
On (1), Off (0)
601 Alternator Fitted
602 Alternator Poles
On (1), Off (0)
603 Under Voltage Shutdown Enable On (1), Off (0)
On (1), Off (0)
604 Under Voltage Trip Shutdown
On (1), Off (0)
605 Under Voltage Warning Enable
On (1), Off (0)
606 Under Voltage Warning Trip
On (1), Off (0)
607 RESERVED
608 Loading Voltage
0 (Action)
609 Over Voltage Warning Enable
0 s
610 Over Voltage Warning Return
611 Over Voltage Warning Trip
0 (Input Source)
612 Over Voltage Shutdown Trip
0 (Polarity)
Under Frequency Shutdown
0 (Action)
613
Enable
0 (Arming)
614 Under Frequency Shutdown Trip 0.0 Hz
0 s
Under Frequency Warning
0 (Input Source)
615
Enable
0 (Polarity)
616 Under Frequency Warning Trip
0 (Action)
617 RESERVED
0 (Arming)
618 Loading Frequency
0 s
619 Nominal Frequency
0 (Input Source)
Configuration Parameters – Mains (Page 7)
0 (Polarity)
701 AC System
0 (Action)
702 Mains Failure Detection
0 (Arming)
703 Immediate Mains Dropout
0 s
704 Under Voltage Enable
0 (Input Source)
705 Under Voltage Level
0 (Polarity)
706 Under Voltage Return
0 (Action)
707 Over Voltage Enable
0 (Arming)
708 Over Voltage Return
0 s
Configuration Parameters – Engine (Page 8)
0 (Input Source)
801 Start Attempts
0 (Polarity)
802 Over Speed Overshoot
0 (Action)
803 Over Speed Delay
0 (Arming)
Gas Choke Timer
804
0 s
(Gas Engine Only)
0 (Input Source) Gas On Delay
805
0 (Polarity) (Gas Engine Only)
0 (Action) Gas Ignition Off Delay
806
(Gas Engine Only)
0 (Arming)
0 s Crank Disconnect On Oil
807
Pressure Enable
0 (Input Source)
Check Oil Pressure Prior To
0 (Polarity)
808
Starting
0 (Action)
809 Crank Disconnect On Oil
0 (Arming)
810 Crank Disconnect On Frequency 0.0 Hz
0 s
Crank Disconnect On Engine
811
Speed
0 (Output Source)
812 Under Speed Enable
0 (Output Polarity)
813 Under Speed Trip
0 (Output Source)
814 Over Speed Trip
0 (Output Polarity)
815 Low Battery Voltage Enable
0 (Output Source)
816 Low Battery Voltage Trip
0 (Output Polarity)
Sensor Type
Percentage Sensor List
Index Type
Index Type
0 Not Used
0 None
1 Dig Closed for Alarm
1 Digital Input
2 Dig Open for Alarm
2 Percentage Sensor
3 VDO Ohm (10-180)
3 Pressure Sensor
4 VDO Tube (90-0)
4 Temperature Sensor
5 US Ohm (240-33)
6 GM Ohm (0-90)
Digital Input Polarity
7 GM Ohm (0-30)
Index Polarity
8 Ford (73-10)
0 Close to Activate
9 User Defined
1 Open to Activate
510 Return Delay 519 Delayed Load Output 2
511 Cooling Time 520 Delayed Load Output 3
512 ETS Solenoid Hold 521 Delayed Load Output 4
513 Failed To Stop Delay 522 Power Save Mode Delay
514 Generator Transient Delay 523 Deep Sleep Mode Delay
515 Transfer Time 524 Page Timer
516 Breaker Trip Pulse 525 Cooling Time at Idle
517 Breaker Close Pulse
518 Delayed Load Output 1
On (1), Off (0) 620 Over Frequency Warning Enable On (1), Off (0)
0 621 Over Frequency Warning Return 0.0 Hz
622 Over Frequency Warning Trip 0.0 Hz
0 V 623 Over Frequency Shutdown Enable On (1), Off (0)
On (1), Off (0) 624 Over Frequency Shutdown Trip 0.0 Hz
0 V 625 AC System 0 (AC System)
626 CT Primary 0 A
0 V 627 Full Load Rating 0 A
On (1), Off (0) 628 Immediate Over Current Enable On (1), Off (0)
Delayed Over Current Alarm
0 V 629 On (1), Off (0)
Enable
0 V 630 Delayed Over Current Alarm Action 0 (Action)
0 V 631 Over Current Delay Time 0 s
On (1), Off (0) 632 Over Current Trip 0 %
633 kW Rating 0 kW
On (1), Off (0) 634 Over kW Protection Enable On (1), Off (0)
0.0 Hz 635 Over kW Protection Action 0 (Action)
636 Over kW Protection Trip 0 %
0.0 Hz 637 Over kW Protection Trip Delay 0 s
0.0 Hz 638* Enable CT Support On (1), Off (0)
0 (AC System) 709 Over Voltage Level Trip
On (1), Off (0) 710 Under Frequency Enable
On (1), Off (0) 711 Under Frequency Trip
On (1), Off (0) 712 Under Frequency Return
0 V 713 Over Frequency Enable
0 V 714 Over Frequency Return
On (1), Off (0) 715 Over Frequency Trip
0 V
0 817 Low Battery Voltage Return
0 % 818 Low Battery Voltage Delay
0 s 819 High Battery Voltage Enable
0 s 820 High Battery Voltage Return
0 s 821 High Battery Voltage Trip
High Battery Voltage Warning
0 s 822
Delay
On (1), Off (0) 823 Charge Alt Shutdown Enable
On (1), Off (0) 824 Charge Alt Shutdown Trip
0.00 Bar 825 Charge Alt Shutdown Delay
826 Charge Alt Warning Enable
0 RPM 827 Charge Alt Warning Trip
On (1), Off (0) 828 Charge Alt Warning Delay
0 RPM 829 Low Battery Start Arming
0 RPM 830 Low Battery Start Threshold
On (1), Off (0) 831 Low Battery Start Delay
0.0 V 832 Low Battery Start Run Time
Digital Input Alarm
AC System Power Up Mode
Arming
Index Type Index Arming Index
0 2 Phase 3 Wire (L1-L2) 0 Always 0
1 2 Phase 3 Wire (L1-L3) 1 From Safety On 1
2 3 Phase 3 Wire 2 From Starting 2
3 3 Phase 4 Wire 3 Never
4 3 Phase 4 Wire (Delta)
5 Single Phase 2 Wire
Output Polarity Alarm Action
Index Polarity Index Action
0 Energise 0 Electrical Trip
1 De-Energise 1 Shutdown
2 Warning
Configuration Parameters – Analogue Inputs (Page 9)
901 Analogue Input A Senor Type
902 Analogue Input A Sensor Selection
903 Low Oil Pressure Enable
904 Low Oil Pressure Trip
905 Oil Pressure Sender Open Circuit
906 Analogue Input B Senor Type
907 Analogue Input B Sensor Selection
908 High Engine Temperature Trip
909 Temperature Sender Open Circuit
910 Analogue Input C Sensor Usage
911 Analogue Input C Senor Type
912 Analogue Input C Sensor Selection
913 Flexible Sensor C Arming
914 Flexible Sensor C Low Alarm Action
915 Flexible Sensor C Low Alarm Trip
916 RESERVED
917 Flexible Sensor C Low Pre-Alarm Enable
918 Flexible Sensor C Low Pre-Alarm Trip
919 Flexible Sensor C Low Pre-Alarm Return
920 RESERVED
921 Flexible Sensor C High Pre-Alarm Enable
922 Flexible Sensor C High Pre-Alarm Return
923 Flexible Sensor C High Pre-Alarm Trip
924-925 RESERVED
926 Flexible Sensor C High Alarm Action
927 Flexible Sensor C High Alarm Trip
928-929 RESERVED
930 Fuel Sensor C Low Shutdown Enable
931 Fuel Sensor C Low Shutdown Trip
932 Fuel Sensor C Low Shutdown Delay
933 Fuel Sensor C Low Pre-Alarm Enable
934 Fuel Sensor C Low Pre-Alarm Trip
935 Fuel Sensor C Low Pre-Alarm Return
936 Fuel Sensor C Low Pre-Alarm Delay
0 V
937 Fuel Sensor C High Pre-Alarm Enable
On (1), Off (0)
938 Fuel Sensor C High Pre-Alarm Return
0.0 Hz
939 Fuel Sensor C High Pre-Alarm Trip
0.0 Hz
940 Fuel Sensor C High Pre Alarm Delay
On (1), Off (0)
941 RESERVED
0 Hz
942 Fuel Sensor C High Alarm Action
0.0 Hz
943 Fuel Sensor C High Alarm Trip
944 Fuel Sensor C High Alarm Delay
Configuration Parameters – Scheduler (Page 10)
0.0 V
1001
0:00:00
1002
On (1), Off (0)
1003
0.0 V
1004, 1008, 1012, 1016, 1020, 1024, 1028, 1032
1005, 1009, 1013, 1017, 1021, 1025, 1029, 1033
0.0 V
1006, 1010, 1014, 1018, 1022, 1026, 1030, 1034
1007, 1011, 1015, 1019, 1023, 1027, 1031, 1035
0 s
Configuration Parameters – Time (Page 11)
1101 Time of Day 0:00:00
On (1), Off (0)
1102 Day of Week 0 (1=Monday)
1103 Week of Year 1-52
0.0 V
Configuration Parameters – Maintenance Alarms (Page 12)
0 s
On (1), Off (0)
1201 Oil Maintenance Alarm Enable On (1), Off (0)
0.0 V 1202 Oil Maintenance Alarm Action 0 (Action)
Oil Maintenance Alarm Engine
0 s
1203 0 h
Hours
On (1), Off (0)
0.0 V 1204 Air Maintenance Alarm Enable On (1), Off (0)
0 s
1205 Air Maintenance Alarm Action 0 (Action)
0 s
x Functionality in all DSE4510 & DSE4520 variants.
x Functionality in all DSE4520 variants.
Mode
x Functionality in DSE4510 & DSE4520 current sensing variants only
Stop
x Functionality in DSE4510 & DSE4520 RT & RTH variants only.
Manual
x* Functionality in DSE4510 & DSE4520 RT & RTH variants only with version 1.6.71 and later.
Auto
0 (Sensor Type)
0 (Pressure Sensor List)
On (1), Off (0)
0 Bar
On (1), Off (0)
0 (Sensor Type)
0 (Temperature Sensor List)
0.00 °C
On (1), Off (0)
Flexible Sensor (1), Fuel Level Sensor (0)
0 (Sensor Type)
0 (Pressure / Temperature / Percentage Sensor List)
0 (Arming)
0 (Action)
0 % / Bar / °C
On (1), Off (0)
0 % / Bar / °C
0 % / Bar / °C
On (1), Off (0)
0 % / Bar / °C
0 % / Bar / °C
0 (Action)
0 % / Bar / °C
On (1), Off (0)
0 %
0 s
On (1), Off (0)
0 %
0 %
0 s
On (1), Off (0)
0 %
0 %
0 s
0 (Action)
0 %
0 s
Enable Scheduler On (1), Off (0)
Schedule Run On or Off Load On (1), Off (0)
Scheduler Period Weekly(0), Monthly(1)
Start Time (Entry 1-8) 0:00:00
Day (Entry 1-8) 0 (1=Monday)
Week (Entry 1-8) 1, 2, 3 or 4
Duration (Entry 1-8) 0 s
1104 Day of Month 1-31
1105 Month of Year 1-12
1106 Year 0-99
Air Maintenance Alarm Engine
1206 0 h
Hours
1207 Fuel Maintenance Alarm Enable On (1), Off (0)
1208 Fuel Maintenance Alarm Action 0 (Action)
Fuel Maintenance Alarm Engine
1209 0 h
Hours