Deep Sea Electronics Plc 8620 Installation Instructions And Instructions For Use

TYPICAL WIRING DIAGRAM
A larger diagram is available in the operators manual.
DIMENSIONS AND MOUNTING
For flat surface mounting in a Type 1 enclosure to meet UL requirements
DIMENSIONS
240.0mm x 181.1mm x 41.7mm (9.4" x 7.1" x 1.6")
Deep Sea Electronics Plc.
Tel:+44 (0)1723 890099
Fax: +44 (0)1723 893303
LO CALL (from UK BT landlines) :
Telephone 0845 260 8933
Email: support@deepseaplc.com
Web: www.deepseaplc.com
PANEL CUTOUT:
220mm x 160mm (8.7" x 6.3") 220mm x 160mm (8.7" x 6.3")
Deep Sea Electronics inc. Deep Sea Electronics inc.
Phone: +1 (815) 316-8706 8706
Fax: +1 (815) 316- 8708 8708
TOLL FREE (USA only) : Tel: 1 866 636 9703 TOLL FREE (USA only) : Tel: 1 866 636 9703
Email: dsesales@deepseausa.com Email: dsesales@deepseausa.com
Web: www.deepseausa.com Web: www.deepseausa.com
D E E P S E A E L E C T R O N I C S D E E P S E A E L E C T R O N I C S
8 6 2 0 I N S T A L L A T I O N I N S T R U C T I O N S 0 I N S T A L L A T I O N I N S T R U C T I O N S
ACCESSING THE FRONT PANEL CONFIGURATION EDITOR. ACCESSING THE FRONT PANEL CONFIGURATION EDITOR.
•
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset
•
Press the Stop/Reset and Info
•
If a module security PIN has been set, the PIN number request is then If a module security PIN has been set, the PIN number request is then
shown :
•
Press the button the first digit will flash to
•
Press (up) or (down to adjust
•
Press (right) when the first digit is c
show '#' for security.
•
Repeat this process for the other digits of the PIN number. You can press
back to adjust one of the previous digits.
•
When is pressed after editing the final
not correct, you must re-enter the PIN.
•
If the PIN has been successfully entered (or the module PIN has not been If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :
EDITING A PARAMETER
•
Enter the editor as described above.
•
Press the or to cycle to the section you wish to view/change. to cycle to the section you wish to view/change. Then press
to cycle to the parameter within the section you have chosen. within the section you have chosen.
•
To edit the parameter, press to enter edit mode. The parameter begins to flash to indicate that to enter edit mode. The parameter begins to flash to indicate that
you are editing the value.
•
Press the up or down buttons to change the parameter to the required value. change the parameter to the required value.
•
Press to save the value. The parameter . The parameter ceases flashing to indicate that it has been saved.
•
To exit the editor at any time, press and hold the To exit the editor at any time, press and hold the
NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to NOTE: When the editor is visible, it is automatically exited after 5 NOTE: When the editor is visible, it is automatically exited after 5
ensure security. ensure security. ensure security. ensure security.
NOTE: The PIN number is automatically reset when the editor is exited (manually or NOTE: NOTE: NOTE: The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or The PIN number is automatically reset when the editor is exited (manually or
automatically) to ensure security. automatically) to ensure security. automatically) to ensure security. automatically) to ensure security.
NOTE: NOTE: More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the 86 More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the
NOTE: NOTE: More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the More comprehensive module configuration is possible using the
configuration software configurati on software. . . . Please contact us for further details Please contact us for further details Please contact us for further details Please contact us for further details
configurati configurati on software on software Please contact us for further details Please contact us for further details Please contact us for further details Please contact us for further details
NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module NOTE: The contents of the tables overleaf may differ depending on the actual module
configuration. configuration. configuration. configuration.
buttons simultaneously. buttons simultaneously.
to enable the pin to be entered.
adjust it to the correct value)
s correctly entered. The digit you have just entered will now
f the PIN number. You can press (left) if you need to move
al PIN digit, the PIN is checked for validity. If the number is
or button.
minutes of inactivity to minutes of inactivity to minutes of inactivity to
86xx series PC xx series PC
86 86 xx series PC xx series PC
053-129
ISSUE 1
button.
or