ORiNG IGPMC-111GP Quick Installation Manual

Media Media
Converter Converter
Q I
uick nstallation
I N D U S T R I A L
Introduction
The IGPMC-111GP is a cost-effective solution for conversion between
10/100/1000Base-T(X) and 100/1000Base-X SFP interfaces, allowing you to
extend communication distance by optical fiber. The device supports
MDI/MDIX auto detection, so you don't need to use crossover wires. With a
10/100/1000Base-T(X) P.S.E. (Power Sourcing Equipment) port, the device
can transmit electrical power up to 30 watts, along with data, to remote
devices over standard twisted-pair cable in an Ethernet network. It also
supports LFP (Link Fault Pass-through). When one side of the link fails,
the other side continues to transmit packets and will wait for a response
that never arrives from the disconnected side. LFP can be easily enabled
using the DIP switch. Once enabled, the link will shut down as soon as it is
notified that the other link has failed, giving the application software a chance
to react to the situation. The IGPMC-111GP
C
temperature range from -40~75° and a wide voltage range between
50~57 VDC, so it is suitable for harsh operating environments.
Package Contents
The series is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Contents Pictures Number
IGPMC-111GP
DIN-rail Kit
Wall-mount Kit
QIG
4-pin terminal block
Preparation
Before installation, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using
web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed cabinet, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
Reduced Air Flow: Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Q I G
IGPMC-111GP
G
uide
Mechanical Loading:
a hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading:
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Dimension (Unit: mm)
has a wide operating
IGPMC-111GP
P1 P2 LFP
LNK/ACT DPX Fault
PoE
Fault Relay
2
SW 1
100/1000X
Fail Close
100
LFP
LFP
stop
SW 2 PoE
Fail Open
LNK/ACT
1
Speed
ETH 10/100/1000M
X 1
41.0
X 1
Panel Layouts
Front Panel
X 2
IGPMC-111GP
1
P1 P2 LFP
2
LNK/ACT DPX Fault
3
PoE
X 1
2
7
100/1000X
X 1
100
8 LFP
LFP
stop
PoE
SW 2
9
10
1
11
ETH 10/100/1000M
Top Panel
1 2
1907-2-29-IGPMC111GP-1.0
IGPMC-111GP
in-rail
Mounting of the equipment in the d should be such that
Consideration should be given to the connection of the equipment to
22.6
20.0 28.0
22.0
13.1
70.0 41
20.0
14.0 13.5
P1
P2
LFP
1. Power LED
4
2. LNK/ACK LED for SFP port
5
3. PoE power status
6
4. LFP status LED
Fault Relay 5. Fault LED
P1
12
P2 6. Duplex LED for Giga port
LFP
SW 1
7. SFP port
Fail Close
8. DIP-switch 2
13
9. Giga port LNK/ACT LED
10. Giga port
Fail Open 11. Giga port speed LED
LNK/ACT
12. DIP-switch 1
13. Faulty terminal
Speed
Real Panel
1. Din-rail screw holes
1. Wall-mount screw
holes
2. Terminal block
1
PRINTED ON RECYCLED PAPER
Industrial Gigabit PoE Media
Converter
Installation
DIN-rail Installation
Step 1: Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Step 2: Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
40.0
Wall-mounting
Step 1: Screw the two pieces of wall-mount kits onto both sides of the switch. A
total of eight screws are required, as shown below.
Step 2: Use the switch, with wall mount plates attached, as a guide to mark the correct
locations of the four screws.
Step 3: Insert four screw heads through the large parts of the keyhole-shaped apertures, and
then slide the switch downwards. Tighten the four screws for added stability.
Version 1.0
IGPMC-111GP
P1 P2 LFP
LNK/ACT DPX Fault
PoE
Fault Relay
P1
P2
2
LFP
SW 1
100/1000X
Fail Close
100
LFP
LFP
stop
SW 2 PoE
Fail Open
LNK/ACT
1
Speed
ETH 10/100/1000M
Quick Installation Guide