ORiNG IMC-B111ETB Series Quick Installation Manual

Media Media
Converter Converter
Q I
uick nstallation
I N D U S T R I A L
Introduction
The IMC-B111ETB series is a cost-effective solution for extending an
Ethernet connection beyond its inherent distance limitation. The series
includes models using -RJ45 or terminal block interfaces. The -RJ45 model
extends the distance to 300 meters using a UTP cable or 200meters using a
24AWG cable, and the terminal block model extends the distance to
200meters using a 24AWG cable. The -RJ45 model supports 2/4/8-wired
auto detecting transmission, and the TB model supports 2-wired
transmission. The series provides a wide operating temperature range
o
from -40~75 C, making it suitable for harsh operating environments.
Package Contents
The series is shipped with the following items. If any of these items is missing
or damaged, please contact your customer service representative for
assistance.
Contents Pictures Number
IMC-B111ETB-TB or
IMC-B111ETB-RJ45
DIN-rail Kit
Wall-mount Kit
QIG
DC plug
Preparation
Before installation, make sure you have all of the package contents
available and a PC with Microsoft Internet Explorer 6.0 or later, for using
web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed cabinet, the operating
ambient temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the maximum ambient temperature (Tma) specified
by the manufacturer.
Reduced Air Flow: Installation of the equipment should be such that the
amount of air flow required for safe operation of the equipment is not
compromised.
Mechanical Loading: Mounting of the equipment in the d
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
IMC-B111ETB Series
IMC-B111ETB Series
G
uide
Dimension (Unit: mm)
IMC-B111ETB-RJ45
P1 P2
ACT LNK
2
Ext.
Ext. Mode
Slave Master
Auto Manual
1
ETH 100M
26.1
X 1
X 1
Panel Layouts
X 2
Front Panel
IMC-B111ETB-RJ45
1 2
X 1
P1 P2
3 4
ACT LNK
8 .
X 1
. .
5 . .
2
.
1
Ext.
Ext. Mode
Slave Master
6
Auto Manual
7
1
ETH 100M
Top Panel
1 2
1
in-rail
should be
1907-2-29-IMCB111ETB-1.0
22.6
22.0 20.0 28.0
13.1
70.0
26.1
20.0
IMC-B111ET-TB
P1 P2
ACT LNK
14.0
8 .
2
. .
. . 2
.
1 1
Ext.
Ext. Mode
Slave Master
Auto Manual
1
ETH 100M
1. PWR1 LED
IMC-B111ET-TB
1 2 2. PWR2 LED
P1 P2
3 4 3. Indicator for extension port action
ACT LNK
4. Indicator for extension port connection status
5. Extension port (terminal block for -TB
model and RJ45 port for -RJ45 model )
2
5
2
6. DIP switch for mode selection of extension port
1
Ext. 7. LAN Port
Ext. Mode
Slave Master
6
Auto Manual
7
1
ETH 100M
Real Panel
3
1. Wall-mount screw 1. Din-rail screw holes
holes
G 2. Terminal block
3. Frame ground
1
PRINTED ON RECYCLED PAPER
Industrial Extended Media Converter
Installation
DIN-rail Installation
Step 1: Slant the switch and screw the Din-rail kit onto the back of the switch, right in the
middle of the back panel.
Step 2: Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch clicks into
the rail firmly.
23.0
6.05
Wall-mounting
Step 1: Screw the two pieces of wall-mount kits onto both sides of the switch. A
total of eight screws are required, as shown below.
Step 2: Use the switch, with wall mount plates attached, as a guide to mark the correct
locations of the four screws.
Step 3: Insert four screw heads through the large parts of the keyhole-shaped apertures, and
then slide the switch downwards. Tighten the four screws for added stability.
Version 1.0
IMC-B111ET-TB
P1 P2
ACT LNK
2
Ext.
Ext. Mode
Slave Master
Auto Manual
1
ETH 10/100M
Quick Installation Guide