Related Manuals for MasterCraft 058-9805-6
Summary of Contents for MasterCraft 058-9805-6
- Page 1 058-9805-6 AIR BRUSH COMPRESSOR & AIR BRUSH KIT IMPORTANT: INSTRUCTION Please read this manual carefully before running this air brush MANUAL compressor & air brush kit and save it for reference.
-
Page 2: Table Of Contents
Mastercraft is Canadian Tire’s exclusive line of reliable and hardworking hand tools, power tools and hardware products. Designed for the DIY customer but with the features and benefits of the leading professional series tools, there are over 100 practical and powerful products available under 6 different categories including;... -
Page 3: Specifications
058-9805-6 | contact us 1-800-689-9928 model no. 058-9805-6 | contact us 1-800-689-9928 SAfETY GUIDElINES SPECIfICATIONS Power 120 V 60 Hz 1.1 A WORK AREA SAfETY WARNINGS • Keep work area clean and well-lighted. Cluttered or dark areas invite accidents. - Page 4 058-9805-6 | contact us 1-800-689-9928 AIR bRUSH COMPRESSOR AND AIR bRUSH SAfETY WARNINGS • During cleaning and flushing, solvents can be forcefully expelled from liquid and air passages which could cause eye injury. Be sure that all others in the area are wearing impact- Risk of fire or explosion —...
-
Page 5: Key Parts Diagram
058-9805-6 | contact us 1-800-689-9928 GUIDElINES fOR USING EXTENSION CORDS KEY PARTS DIAGRAM Verify that the extension cord is in good condition. When using an extension cord, be sure to use one that Description Description is heavy enough to carry the current that the tool will draw. -
Page 6: Operating Instructions
058-9805-6 | contact us 1-800-689-9928 model no. 058-9805-6 | contact us 1-800-689-9928 SETUP Of AIR bRUSH COMPRESSOR AND AIR bRUSH (fig. 1) OPERATING INSTRUCTIONS (fig. 2 to 3) 1. Insert the compressor power cord plug (4) into the nearest 120-volt, grounded, electrical outlet. -
Page 7: Model No. 058-9805-6 | Contact Us 1-800
058-9805-6 | contact us 1-800-689-9928 10. After flushing the air brush unit completely with the proper solvent, spray any remaining solvent through TRIGGERING EXERCISES the nozzle until clear solvent sprays from the end of the air brush tip. -
Page 8: Model No. 058-9805-6 | Contact Us 1-800
058-9805-6 | contact us 1-800-689-9928 4. Do not hold the air brush too close to Exercise 4 - Even Tones the paper or hold the finger lever all the Fig. 8 Fig. 9 IMPORTANT: Use masking tape to mask off several square areas on a piece of paper for Exercises 4 and 5. -
Page 9: Maintenance
058-9805-6 | contact us 1-800-689-9928 2. Fig. 15 is a combination of masking and varying MAINTENANCE shades. This spraying exercise trains the eye to make Fig. 16 AIR bRUSH COMPRESSOR sure that each square has the same tone value. -
Page 10: Screw
058-9805-6 | contact us 1-800-689-9928 NEEDlE REMOVAl AND ClEANING (fig. 19) TROUblESHOOTING 1. Hand loosen the needle chucking nut counter- Fig. 19 AIR bRUSH COMPRESSOR clockwise. Problem Possible Causes likely Solutions 2. Carefully pull the needle out of the air brush. -
Page 11: Filter:
058-9805-6 | contact us 1-800-689-9928 AIR bRUSH AIR bRUSH COMPRESSOR Problem Possible Causes likely Solutions Will not spray. 1. Misuse of finger lever. 1. First press finger lever downward and then draw 2. Needle chucking nut gets back on the finger slowly/gently till fluid comes loose. -
Page 12: Note
058-9805-6 | contact us 1-800-689-9928 AIR bRUSH AIR bRUSH COMPRESSOR Description Qty. Description Qty. Screw Front gasket Read cover Front cover Block Water drain valve continuation tabs Rear body O-ring Screw Cylinder block Stationary motor O-ring... - Page 13 3-Year limited Warranty Additional limitations This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase This warranty applies only to the original purchaser and may not be transferred. Neither the retailer not...
Need help?
Do you have a question about the 058-9805-6 and is the answer not in the manual?
Questions and answers