Zte ZXG10-BS30 Installation Manual
  1. Manuals
  2. Brands
  3. Zte Manuals
  4. Accessories
  5. ZXG10-BS30
  6. Installation manual

Zte ZXG10-BS30 Installation Manual

Compact outdoor bts
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ZXG10-BS30
Compact Outdoor BTS

Installation Manual

Version 1.5
ZTE CORPORATION
ZTE Plaza, Keji Road South,
Hi-Tech Industrial Park,
Nanshan District, Shenzhen,
P. R. China
518057
Tel: (86) 755 26771900
800-9830-9830
Fax: (86) 755 26772236
URL: http://support.zte.com.cn
E-mail: doc@zte.com.cn

Advertisement

Table of Contents
loading

Related Manuals for Zte ZXG10-BS30

Summary of Contents for Zte ZXG10-BS30

  • Page 1: Installation Manual

    ZXG10-BS30 Compact Outdoor BTS Installation Manual Version 1.5 ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China 518057 Tel: (86) 755 26771900 800-9830-9830 Fax: (86) 755 26772236 URL: http://support.zte.com.cn E-mail: doc@zte.com.cn...

  • Page 2: Revision History

    ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by contractual confidentiality obligations. All company, brand and product names are trade or service marks, or registered trade or service marks, of ZTE CORPORATION or of their respective owners.
  • Page 3 Please fax to: (86) 755-26772236; or mail to Documentation R&D Department, ZTE CORPORATION, ZTE Plaza, A Wing, Keji Road South, Hi-Tech Industrial Park, Shenzhen, P. R. China 518057. Thank you for your cooperation! Document ZXG10-BS30 (v1.5) Compact Outdoor BTS Hardware Installation Manual...
  • Page 4 This page is intentionally blank.

  • Page 5: Table Of Contents

    Contents About this Manual ............. i Purpose ................i Intended Audience ..............i Prerequisite Skill and Knowledge ..........i What is in this Manual ............i Related Documentation............ii Conventions ................ iii How to Get in Touch............. iv Chapter 1................1 Safety Instructions ............
  • Page 6 Installation Preparations..........17 Inspection on Installation Environment......17 Inspection on Indoor Installation Environment ......17 Inspection on Outdoor Environment ........18 Power Supply Requirements ........... 18 Safety Instructions .............. 18 Grounding and Lightning Protection Requirements....19 Tools and Meter Requirements ..........19 Unpacking and Inspection ..........
  • Page 7 Internal RF Cables for Single Cabinet ........57 Internal RF Cables for Dual Cabinets ........58 Internal Signal Cables............59 Chapter 7................ 73 External Cables Installation .......... 73 Chapter 8................ 83 Antenna Feeder System Installation......83 Antenna Feeder System Composition ....... 83 Installation Accessories............
  • Page 8 Appendix C ..............131 Abbreviation..............131 Figures................133 Tables ................137 Index ................139...
  • Page 9 This page is intentionally blank.

  • Page 11: About This Manual

    About this Manual Purpose This manual describes the overall structure, basic parameters, configurations and installation methods of ZXG10-BS30 (V1.5). Intended Audience This document is intended for engineers and technicians who perform hardware installation for ZXG10-BS30 (V1.5). Prerequisite Skill and Knowledge...

  • Page 12: Related Documentation

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Chapter Summary Grounding Cables installation Installation Chapter 6, Internal Describes the back plane interfaces , RF Cable Installation cable and signal cable installation Chapter 7, External Describes the external cables including, Cable Installation...

  • Page 13: Conventions

    About this Manual Conventions Typographical ZTE documents employ the following typographical conventions. Conventions 2 - T A B L E Y P O G R A P H I C A L O N V E N T I O N S...

  • Page 14: How To Get In Touch

    (86) 755 26772236. You can also browse our website at http://support.zte.com.cn, which contains various interesting subjects like documentation, knowledge base, forum and service request.

  • Page 15: Chapter 1

    In case of any conflict, local safety regulations shall prevail. Maintenance personnel should have preliminary knowledge about safety operations and must have received training on ZTE equipment maintenance and operations. Observe related equipment precautions and special safety instructions during maintenance, provided by ZTE.
  • Page 16 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Safety Symbol Meaning No touching: Do not touch. Universal alarm: General safety precaution. Erosion: Beware of erosion. Electric shock: There is a risk of electric shock. Electrostatic: Device may be sensitive to static electricity.

  • Page 17: Toxicant

    DC and AC power. Do not wear a watch, chain, bracelet, ring or any other conductive objects while working with high voltages. Prevent moisture from entering the equipment while working in a moist environment. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 18: Antistatic

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Power Cables Note: Never install or uninstall power cables while they are live because when touched with a conductor may produce sparks, resulting in fire or damage to eyes. Shut down the power supply before installing or uninstalling a power cable.

  • Page 19: Battery

    If acid liquid has overflowed, dispose off according to the local regulations of chemical or special waste disposal. Acid Liquids Danger: If acid liquid overflows, absorb and neutralize it as soon as possible. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 20: Electromagnetic Radiation

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Take special care of the acid liquids while moving a soaked battery. If acid liquid overflows, use NaHCO3, Na2CO3 or Na2CO3.10H2O to neutralize and absorb it. Substances used for absorption and neutralization of acid liquids must conform to battery manufacturers’...

  • Page 21: Fans

    While working with devices near the fan, keep fingers or devices away from the fan to avoid human injury or damage to devices. High Temperature Warning: Surface temperature of some components is very high. Do not touch it. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 22: Plugging/Unplugging A Module

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Plugging/Unplugging a Module Note: Do not plug a board with force as it might bend the pins at the backplane. Insert the board along the slot. While holding a board in hand, keep hands off the board circuits, components, connectors and wiring.

  • Page 23: Chapter 2

    This chapter describes the installation and commissioning flow of ZXG10-BS30 (V1.5) which makes the installation personnel to have a complete understanding of the installation process. Physical parameters of ZXG10-BS30 (V1.5) such as size, weight, humidity and temperature also explained in this chapter. Equipment Installation and...
  • Page 24 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual carried out jointly by the installation team and ZTE. If any party does the unilateral unpacking then that party is liable for any damage to boards/parts or short shipment found during unpacking.

  • Page 25: Equipment Parameters

    O M M I S S I O N I N G L O W Equipment Parameters Dimensions Dimension of the integrated equipment not including the base (Height x Weight x Depth) is 500 mm x 400 mm x 284 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 26 Heating Module (HTM) SDH Transmission Module (STM) Power Module (PWM) Power Supply ZXG10-BS30 (V1.5) supports power supply of 220 V AC and -48 V DC. 220 V AC power supply Allowed voltage fluctuation range: 130 V to 300 V Allowed frequency fluctuation range: 45 Hz to 65 Hz Output voltage: -48 V DC (-60 V DC to -40 V DC Maximum output current: >6 A...

  • Page 27: Hardware Installation Flow

    Safety: Safety meets Safety of Information Technology Equipment (GB 4943-1995) standard. Hardware Installation Flow ZXG10-BS30 (V1.5) can be installed in various methods which include installation on walls or supportive poles depending upon the geographic environment. Installation on the wall is simple and low cost but it is applicable only if there is an existing wall.
  • Page 28 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 2 – H I G U R E A R D W A R E N S T A L L A T I O N L O W Cabinet Installation Cabinet installation includes installing the cabinet on the walls and supportive poles.
  • Page 29 Replacing any parts or altering the equipment might result in unexpected danger. Make sure not to replace any parts or alter the equipment without any authorization. Electrostatic: Wear an antistatic wrist strap when installing and maintaining the equipment. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 30 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 31: Chapter 3

    Inspection on Installation Environment ZXG10-BS30 (V1.5) can be used both in outdoor and indoor environment. Internal structure is completely closed to resist against rain and fog. ZXG10-BS30 (V1.5) can work normally under -40 C to +50 It is installed either on wall or supportive pole.

  • Page 32: Inspection On Outdoor Environment

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Equipment room should have lighting systems which includes daily lighting, standby lighting and emergency lighting for maintenance purpose. Floor, walls, ceiling, reserved holes and troughs should be constructed as per requirements. Pipes for water supply, drainage and gas should not be inside the equipment room.

  • Page 33: Grounding And Lightning Protection Requirements

    Chapter 3 - Installation Preparations Grounding and Lightning Protection Requirements ZXG10-BS30 (V1.5) is an outdoor Base Transceiver Station with proper lightning protection. To prevent the equipment from lightning, lightning arrester ground and cabinet protection ground should be connected separately to improve the performance of the equipment.

  • Page 34: Unpacking And Inspection

    During unpacking total number of goods delivered should be checked against ZTE Corporation Checklist before installation. Once ZTE engineer arrives at the installation site they should count and check the delivered goods together with the user. Unpacking and Accepting Report should be prepared after completing the unpacking and inspection process.
  • Page 35 1. Remove the upper cover of the wooden case. 2. Remove the foam plate from the wooden case. 3. Take out the equipment directly from the wooden case. Counting the Goods After unpacking, check the goods against the packing list. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 36 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual User and vendor should sign the Unpacking and Inspection Report and submit it to the local ZTE office and ZTE Engineering Department before the specified time limit. Equipment Inspection Check whether core module is scratched or deformed.

  • Page 37: Chapter 4

    C h a p t e r Cabinet Installation Cabinet Types ZXG10-BS30 (V1.5) is an outdoor BTS enclosed by a sealed cabinet with resists water, dust and burglary. ZXG10-BS30 (V1.5) is designed to provide safety during installation, operation and maintenance.

  • Page 38: Tsme

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Duplexer Module (DPM) Extended Transceiver Module (ETRM) Backplane Connection Unit (BCU) Controller and Maintenance Module (CMM) SDH Transmission Module (STM) Power Module (PWM) Heating Module (HTM) Fan unit 6 – Z X G 1 0 - B S 3 0 ( V 1 . 5 ) O...

  • Page 39: Dpm

    DPM size (Length x Width x Height) is 273 mm x 215 mm x 128 8 – D P M S I G U R E T R U C T U R E Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 40: Stm

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 1. LAU 3. DPU 2. DSWR 4. RFU ZXG10-BS30 (V1.5) supports multi transmission modes such as SDH, HDSL, microwave satellite. transmission equipment can be implemented by configuring STM. ZXSM T150 compact synchronous digital transmission equipment (T150) is used as STM which provides 155 Mbits/s SDH interface for diversified BS transmission interfaces.

  • Page 41: Pwm Or Pwmd

    1. Conversion board 2. HDSL PWM or PWMD ZXG10-BS30 (V.5) supports 220 V AC and -48 V DC. Power module configured as per user requirement can be PWM or PWMD. PWM consists of a circuit breaker, two AC connectors, two DC connectors and two power indicators.
  • Page 42 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Two AC connectors are used for 220 V AC input and 220 V AC output power. 220 V AC output supplies power to the heater. L, N and PE denote 3 pin AC connectors.

  • Page 43: Htm

    HTM maintains the cabinet temperature for normal operation of the equipment at low temperature. 1 4 – H T M S I G U R E T R U C T U R E 1. Heater 2. Fan Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 44: Cabinet Installation Methods

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Cabinet Installation Methods Cabinet can be installed on wall or supportive pole. Cabinet Installation on a Pole Single Cabinet Steps to be followed during single cabinet installation on an antenna pole. 1. Fixing support should be removed from the cabinet.
  • Page 45 5. If necessary, tie the rope on the pedestal for lifting the cabinet to a position. 6. Shadow shield should be fixed to the support assembly behind the cabinet using four M4 screws as shown in Figure Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 46 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 1 8 – S I G U R E H A D O W H I E L D N S T A L L A T I O N Warning: Avoid objects from falling off when working at heights.
  • Page 47 Figure 21 and Figure 22. 2 1 – C ( 1 ) I G U R E A B I N E T I X A T I O N 1. Suspension bar Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 48 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 2 2 – C ( 2 ) I G U R E A B I N E T I X A T I O N 2. Second cabinet should be installed as shown in Figure 23.

  • Page 49: Cabinet Installation On A Wall

    N S T A L L A T I O N Cabinet Installation on a Wall Single Cabinet Steps to be following during cabinet installation on a wall. 1. Fixing support should be removed from the cabinet. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 50 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 2. Mark four points on the wall based on the holes in the fixing support. 3. Drill four holes on the wall using M12 percussion driller. 4. Fixing support should be fixed on the wall using four M12 expansion bolts as shown in Figure 26 and Figure 27.
  • Page 51 T T A C H I N G T H E A B I N E T 6. Align the fixing support with the cabinet screw holes. 7. Tighten the four M8 internal hexagonal screws as shown in Figure 29. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 52: Figure 30 - Installed Cabinet

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 2 9 – C I G U R E A B I N E T I X A T I O N 1. M8 Screws Installed cabinet is shown in Figure 30.Shadow shielding should be installed if the cabinet is installed in outdoor environment.

  • Page 53: Plugging / Unplugging A Module

    Steps to be followed when plugging / unplugging a module 1. Remove the TSME first if DPM need to be removed. 2. Remove the module carefully by unfastening the module screws using screw driver. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 54: Figure 33 - Removing Tsme Module

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 3. Module should be kept in the exact position with screws tightened during installation. 4. Direction for removing TSME module is shown in Figure 33 and installation is just the reverse. 3 3 – R...

  • Page 55: Figure 35 - Removing Dpm Module

    I G U R E E M O V I N G M O D U L E 1. STM Direction for removing HTM module is shown in Figure 37 and installation is just the reverse. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 56: Figure 37 - Removing Htm Module

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 3 7 – R H T M I G U R E E M O V I N G M O D U L E 1. HTM Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 57: Chapter 5

    C h a p t e r Power and Grounding Cables Installation This chapter describes about the interfaces and installation of power and grounding cables for ZXG10-BS30 (V1.5). Power Interface AC and DC power interfaces shown in Figure 38 are located at the cabinet bottom.

  • Page 58: Dc Input Power Interface

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 6 – 2 2 0 V A C I A B L E N P U T O W E R N T E R F A C E E S C R I P T I O N S...

  • Page 59: Dc Output Power Interface

    ZXG10-BS30 (V1.5) grounding includes Lightning Protection Box Grounding and Cabinet Grounding. Lightning Protection Box Grounding Lightning protection for ZXG10-BS30 (V1.5) includes Grade C Lightning protection box and Grade D power lightning protection. For perfect grounding, lightning protection box should be grounded separately.

  • Page 60: Figure 39 - Cabinet Grounding

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 3 9 – C I G U R E A B I N E T R O U N D I N G 1. Back plane grounding 2. Cabinet grounding Aluminum sections of the cabinet main body are subjected to conductive oxidant treatment in order to make the cabinet a good conductor.
  • Page 61 Chapter 5 - Power and Grounding Cables Installation system is used as working ground for ZXG10-BS30 (V1.5) then grounding resistance should be less than 5 ohm. If soil resistance ratio is high and grounding resistance not as per requirement then, high resistance soil should be replaced with low resistance soil or resistance–deceasing agent should...
  • Page 62 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 63: Chapter 6

    Internal Cables Installation This chapter describes the connection between backplane interfaces and internal RF and signal cables installation. Internal cables for ZXG10-BS30 (V1.5) should be changed depending upon the site configurations based on the instructions given in this chapter. Backplane Interfaces DBCU transfers the signals between internal modules, cabinets and between cabinet and BSC.

  • Page 64: Figure 42 - Dbcu Components

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual interface, Input main contact point interface, Site ID interface and power interface. E1 interface includes two way data transmission between BSC and BTS, data interface between cabinets, two way data transmission between Master and Slave cabinet.

  • Page 65: Site Id

    Two DIP switches S1 and S2 on DBCU serves as ID_DOG for the cabinet. Remove the CMM I/O interface and connect DIP switch. If DIP switch is ON, signal line is grounded and ID status collected by CMM is 0 otherwise it is 1. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 66: Figure 43 - Id Numbering

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual ID is a 16 bit number as shown in Figure 43. S1 and S2 denotes bit 0 to 7 and 7-15 respectively. 4 3 – I D I G U R E...
  • Page 67 M port D port number) 2,1, and 0 ABIS_TS (O TS 16 and M Lapd TS 31 time slots on Abis interface) TS 30 TS 29 TS 28 TS 27 TS 26 TS 25 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 68 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual DIP Settings ZXG10-BS30 (V1.5) DIP settings are shown in Table 10. 1 0 – D I P S Z X G 1 0 - B S 3 0 ( V 1 . 5 )

  • Page 69: Figure 44 - Site Cascading

    I G U R E I T E A S C A D I N G 4 5 – M I G U R E U L T I A S C A D I N G Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 70: Figure 46 - Composite Networking

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 4 6 – C I G U R E O M P O S I T E E T W O R K I N G ETRM layer settings for Master and Slave...

  • Page 71: Internal Rf Cables For Single Cabinet

    A B I N E T SI.NO Cable Cable End A End B name number RF-95802- 626900000400 TSME/TX DPM/TX RF-95802- 626900000700 TSME/RXA DPM/N6 TSME/RXB DPM/N4 RF-95802- 626900000600 DPM/OUT DPM/N1 RF-95802- 626900000500 DPM/Rx DPM/N2 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 72: Internal Rf Cables For Dual Cabinets

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual SI.NO Cable Cable End A End B name number RF-95802- 626900000100 DPM/ANT Ant_TX/RX RF-95802- 626900000800 DPM/RXIN Ant_RX RF-95802- 626900000500 DPM/REV DSWR/X2 DPM/FWD DSWR/X1 Internal RF Cables for Dual Cabinets Interfaces and cabling of internal RF cables for Dual Cabinet in O2 configuration mode is shown in Figure 48 and connection details in Table 13.

  • Page 73: Internal Signal Cables

    Cabinet) Cabinet) Internal Signal Cables Internal signal cables for ZXG10-BS30 (V1.5) are shown in Figure 49, Figure 50, Figure 51 and Figure 52 and connection details in Table 14, Table 15, Table 16 and Table 17. If transmission equipment T150 is built-in, A_IN and A_OUT on the TSME should be connected to the corresponding TSME interfaces.

  • Page 74: Figure 49 - Master Cabinet - 220 V Ac Power Supply

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Master Cabinet – 220 V AC Power Supply 4 9 – M – 2 2 0 V A C P I G U R E A S T E R A B I N E T...
  • Page 75 626922000800 DBCU/A_IN, Built-in 95802- A_OUT transmission equipment / TX/RX (HDSL or SDH equipment) DBCU/X5 Connect only when using SDH or HDSL equipment PWR- 626500000200 Grounding bolt Panel grounding 95802- inside the bolt cabinet Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 76 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Cable Cable End A End B SI.NO Name Number PWR- 626524000100 PWM/AC_IN Cabinet 95802- bottom/AC_IN Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 77: Figure 50 - Master Cabinet - -48 V Dc Power Supply

    A S T E R A B I N E T O W E R U P P L Y Cable Cable number End A End B SI.NO name PWR- 626501010700 Grounding DBCU/GND 95802- bolt inside Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 78 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Cable Cable number End A End B SI.NO name the cabinet Grounding DBCU/GND bolt inside the cabinet PWR- 626527000300 DBCU/X18 As shown in 95802- Figure PWR- 626551000300 DBCU/X20 Entrance 95802- control PWR-...
  • Page 79 / TX/RX (HDSL or equipment) DBCU/X5 Connect only when using SDH or HDSL equipment. PWR- 626500000200 Grounding Panel 95802- bolt inside grounding the cabinet bolt PWR- 626524000100 PWM/DC_IN Cabinet 95802- bottom/-48 V_IN/EXT Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 80: Figure 51 - Slave Cabinet - 220 V Ac Power Supply

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Slave Cabinet – 220 V AC Power Supply 5 1 – S – 2 2 0 V A C P I G U R E L A V E A B I N E T...
  • Page 81 As shown in 95802- in Figure Figure PWR- 626760000200 DBCU/X12 DSWR/X4 95802- PWR- 626521007100 DBCU/X21 PWM/ALM 95802- PWR- 626500000200 Grounding Panel 95802- bolt inside grounding the cabinet bolt PWR- 626524000100 PWM/AC_I Cabinet 95802- bottom/AC_I Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 82: Figure 52 - Slave Cabinet - -48 V Dc Power Supply

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Slave Cabinet - -48 V DC Power Supply 5 2 - S - - 4 8 V D C P I G U R E L A V E A B I N E T...
  • Page 83 95802-019 bottom/-48 V_IN/EXT HDSL Transmission Module Wiring 220 V AC Power Supply HDSL Transmission Module wiring for 220 V AC power supply is shown in Figure 53 and connection details in Table 18. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 84: Figure 53 - Hdsl Transmission Module - 220 V Ac Power Supply

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 5 3 - H D S L T – 2 2 0 V A C P I G U R E R A N S M I S S I O N...

  • Page 85: Figure 54 - Hdsl Transmission Module - -48 V Dc Power Supply

    End A End B Name (Label (Label Content) Content) PWR- PWMD - DBCU 95802-027 48V_OUT HDSL HDSL -48 V DS-95802- DBCUA_IN HDSL_TX DS-95802- DBCUA_OUT HDSL_RX PE-95802- HDSL PE DOOR_PE Data line HDSL DSL Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 86 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 87: Chapter 7

    C h a p t e r External Cables Installation External cables for ZXG10-BS30 (V1.5) include Tail fiber, E1 cable, Power cable and Main contact point alert cable. Fiber splice tray should be installed outside the equipment. Fiber should be spliced in the splice tray and coiled over the water proof tail fiber.

  • Page 88: Figure 55 - Schematic Diagram For External Cables

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 5 5 – S I G U R E C H E M A T I C I A G R A M F O R X T E R N A L A B L E S 1.
  • Page 89 E1 interface receives unbalance input of the 75 ohm coaxial cable. If the interface adopts 120 ohm twisted pair then it must be adopted to 75 ohm coaxial cable using a converter. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 90 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual ZXG10-BS30 (V1.5) provides two pairs of input/output E1 interface led out from cabinet bottom. Refer Table 21 for interface descriptions. 2 1 – D E 1 I A B L E E S C R I P T I O N F O R N T E R F A C E SI.NO...
  • Page 91 Antenna Feeder Interface Antenna is used by the Um interface to transmit radio signals between BTS and MS. ZXG10-BS30 (V1.5) provides three antenna feeder interfaces at the cabinet bottom. Refer Table 23 for interface description. 2 3 – D A B L E...
  • Page 92 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Interfa Line signal Signal Connec Signal Description Descript name cover RX_DIV 900 MHz/1800 Cascade Diversity MHz RF diversity cabinet connect receiving signal receiving signal → ETRM or by waterpr connect otherwis remove...
  • Page 93 Input Main Contact Point Interface ZXG10-BS30 (V1.5) provides Input main contact point interface fed out from the cabinet bottom as shown in Figure 55.Refer Table 25 for Interface details. 2 5 – D A B L E...
  • Page 94 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual If LMT uses serial communication mode, connect local operation and maintenance interface with RS232 serial port of the LMT through dedicated RS232 serial port line. If LMT uses serial network interface communication mode,...
  • Page 95 E S C R I P T I O N F O R I N T E R F A C E Master Cabinet Slave Cabinet M_HW1 S_HW of slave cabinet 1 M_HW2 S_HW of slave cabinet 2 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 96 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 97: Chapter 8

    MS which should be directly connected to pre-receiving filter through feeder cable as shown in Figure 56. Tip: Tower top amplifier is an optional device. Read contract terms for the configuration details. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 98: Figure 56 - Antenna Feeder System Composition

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 5 6 – A I G U R E N T E N N A E E D E R Y S T E M O M P O S I T I O N 1.

  • Page 99: Figure 57 - Omni-Directional (Left) And Directional Antenna (Right)

    Tower top amplifier should be used in antenna feeder system to improve the BTS receiver performance as shown in Figure 58. Tower top amplifier should have separate grounding system. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 100: Figure 58 - Uni-Directional (Left) And Bi-Directional (Right)

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 5 8 – U I G U R E I R E C T I O N A L E F T A N D I R E C T I O N A L I G H T –...

  • Page 101: Figure 60 - Main Feeder Cable

    λ/4 stub lightning arrester is a tri-port passive coaxial component with external and internal conductors short- circuited as shown in Figure 62. Its third end length is 1/4th of the central working wavelength. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 102: Figure 62 -Λ/4 Stub Lightning Arrester

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 6 2 - I G U R E Λ S T U B L I G H T N I N G A R R E S T E R Working principle is similar to a band-pass filter. At working frequency band, it is equal to connecting together with a main coaxial cable to infinite impedance.
  • Page 103 Figure 65. Features: High vibration resistance High reliability Good mechanical and electrical property DIN-type connectors should be used to connect RF coaxial cables in radio devices and equipments under vibration and adverse environments. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 104 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 6 5 – D : 1 / 2 I : 7 / 8 I I G U R E Y P E O N N E C T O R E F T...

  • Page 105: Installation Accessories

    C-39012 and IEC 169-8 specifications. It is used to connect RF coaxial cables in radio equipment and electronic devices. It is used as a trunk connector in ZTE BSS systems. 6 8 – B N C C I G U R E...
  • Page 106 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Feeder window shown in Figure 70 and Figure 71 should be prepared and sealed before feeder cable is led into the equipment room. 7 0 – F ( 1 ) I G U R E...
  • Page 107 Copper grounding bar should be fixed on the wall near the feeder window Figure 74. 7 3 – I I G U R E N D O O R O P P E R R O U N D I N G Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 108 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 7 4 – I I G U R E N D O O R O P P E R R O U N D I N G N S T A L L A T I O N Outdoor Copper Grounding Bar: Outdoor copper grounding bar is shown in Figure 75.

  • Page 109: Antenna Feeder System Installation Flow

    N D O O R A B L I N G A C K Waterproof self-adhesive tape Ultraviolet-proof tape Ultraviolet-proof binding strap Antenna Feeder System Installation Flow Antenna feeder system installation flow is shown in Figure 78. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 110: Engineering Preparation

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 7 8 – A I G U R E N T E N N A E E D E R Y S T E M N S T A L L A T I O N...
  • Page 111 Inspection and performance test should be conducted on jumpers, tower top amplifier (optional), lightning arresters and antennas before delivery to the site. Instructions to be followed during inspection: Packing should be in good condition. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 112 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Materials and accessories should be counted against the packing list. Materials should not be in damaged condition. Materials should be stored properly before installation. Connector Preparation Connectors should be connected used for connecting all the cables in antenna feeder system.
  • Page 113 O A M E D A T E R I A L 11. Remove the connector and check the shape of the external conductor, which should be even and without any foam or copper filings. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 114: Antenna Installation

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 12. To remove the connector, first screw off the plug-in component by 1/4 revolution, and turn the connector fixing component while keeping the connector fixed, as shown in Figure 83. 8 3 – T...
  • Page 115 Directional Antenna Steps to be followed during directional antenna installation: 1. Antenna fixing support should be installed in such a way that it is adjustable as shown in Figure 86. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 116 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 8 6 – A I G U R E N T E N N A I X I N G U P P O R T 2. Use bolts and U-shaped bolts to fix the antenna dip fixing support onto the antenna pole such that input/output ports face downwards, as shown in Figure 87.
  • Page 117 S I N G T H E A T H R E I N Z I M U T H D J U S T I N G O O L 1. Antenna Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 118 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 2. Targeted 3. Observation 4. Telescope direction direction 5. Dial 6. Screws should be tightened using a spanner, as shown in Figure 90. 9 0 – T I G U R E...
  • Page 119 3. Input/output ports of the antennas should be downwards, as shown in Figure 93 4. Make sure that antenna is vertical by measuring with a vertical angle gauge. 5. Screws should be tightened using a spanner. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 120 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 9 3 – O I G U R E M N I I R E C T I O N A L N T E N N A N S T A L L A T I O N...
  • Page 121 Minimum radius for a single bend should be 125 mm as shown in Figure 96. 9 6 – S I G U R E I N G L E B E N D Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 122 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Minimum radius for a multiple bend should be 200 mm as shown in Figure 97. 9 7 – M I G U R E U L T I P L E E N D...
  • Page 123 If the feeder cable length is more than 60 m, it should be grounded in the middle. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 124 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 9. Metallic outer layer is connected to the grounding bus bar through grounding clips, and then a tinplated copper wire with cross section area not less than 95mm2 or zinc-plated flat steel is led out from the bus bar and connected to the grounding point of the iron tower.
  • Page 125 Figure 101. 1 0 1 – S I G U R E E A L I N G T H E E E D E R A B L E O L E S Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 126 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 3. Feeder window should be installed as shown in Figure 102. 1 0 2 – F I G U R E E E D E R I N D O W N S T A L L A T I O N...
  • Page 127 Operating frequency marked on the lightning arrester should match with the operating frequency of the BTS system operating frequency. Grounding Clip Installation Steps to be followed during grounding clip installation: Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 128 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 1. Mark the position on the 7/8 inch feeder cable and strip the sheath of the feeder cable on the installing position of the grounding clip. 2. Place the grip ring of the grounding clip around the external conductor of the feeder cable and buckle the ring as shown in Figure 105.
  • Page 129 5. Take the N connector out from the baffle plate. Adjust the direction of the N connector so that its cross section faces inwards and points to the module panel. Tighten the four screws on the cabinet top to secure the antenna feeder cable. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 130: Testing The Antenna Feeder System

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 6. Plug AEM and ETRM again, connect the RF cables on the panels, and tighten all the connections. Testing the Antenna Feeder System Antenna feeder system should be done to check the installation quality and performance of the antenna feeder system.
  • Page 131 ( R F 1 8 0 0 ) A B L E O W E R E V E L S ETRM Power Level Max Peak Power Tolerance (dB) 0, +3 0, +3 0, +3 0, +3 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 132 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 133: Chapter 9

    Cabinet parts and Cables should be damaged or falling off. No touching: Some devices have high temperature; do not touch them to avoid scald injury Cables Checking Power cables Make sure that power cables are connected with correct polarity. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 134: Sockets, Plugs And Locking Pieces Checking

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Grounding cables Make sure that -48 V GND, GND and PE grounding cables are connected with correct polarity. Internal cables Make sure that HW cables, Alarm cables and clock cables are connected properly.

  • Page 135: Antenna Feeder System

    Chapter 9 - Hardware Installation Check Antenna Feeder System Feeder cables, jumpers and connectors should be in good contact. Lightning arresters should be installed correctly. Fastening screws should be tight and waterproofed. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 136 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 137: Chapter 10

    Switches inside the equipment should be set at the specified start positions. Power-ON Procedure Steps to be followed during Power-ON: 1. Connect the power cable to the 3-core socket 2. Move the power supply switch to ON position to power-ON ZXG10-BS30 (V1.5). Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 138: Power-Off Procedure

    1. Move the power supply switch to OFF position to power-OFF ZXG10-BS30 (V1.5). 2. Remove the power cable from the 3-core socket. To ensure safety and incase of any queries contact local ZTE office or ZTE customer care center. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 139: Packing, Storage And Transportation

    Packing box should contain cabinet, foam material and plastic cover. Place the packing box in a horizontal position on the ground as shown in Figure 108 and unpack as shown in Figure 109. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 140: Storage

    ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual 1 0 8 – P I G U R E A C K I N G ZXG10 BS30室外型一体化GSM基站 1 0 9 - U I G U R E N P A C K I N G T H E...

  • Page 141: Transportation

    Equipment should be not kept in an open ware house. Equipment should not be placed together with flammable and explosive goods. Make sure protect equipment from moisture mechanical damage. Equipment should be loaded and unloaded properly using machines without any rough handling. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 142 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 143: Ce Statement

    (9.84 feet) for 900MHz unit and 2.2M (7.22 feet) for 1800MHz unit from the outside antenna. Exceeding this minimum separation will ensure that the worker or bystander does not receive RF-exposure beyond the Maximum Permissible Exposure according section EN50383:2002 limits Controlled Exposure. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 144 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally blank Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 145: Abbreviation

    Antenna Equipment Module Backplane Connection Unit Controller and Maintenance Module Duplexer Module ETRM Extended Transceiver Module Heating Module Power Module SDH Transmission Module TSME Transceiver for Station Module supports EDGE VSWR Voltage Standing Wave Ratio Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 146 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual This page is intentionally kept blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 147: Figures

    Figure 3 – Schematic Diagram For Grounding Network... 19 Figure 4 – Packing Box ............21 Figure 5 – ZXG10-BS30 (V1.5) Overview ......23 Figure 6 – ZXG10-BS30 (V1.5) Overall Structure ....24 Figure 7 – TSME Structure ..........25 Figure 8 – DPM Structure........... 25 Figure 9 –...
  • Page 148 Figure 45 – Multi-Cascading ..........55 Figure 46 – Composite Networking........56 Figure 47 – Internal RF cables for ZXG10-BS30 (V1.5)... 57 Figure 48 – Internal RF cables for Dual Cabinets ....58 Figure 49 – Master Cabinet – 220 V AC Power Supply .... 60 Figure 50 –...
  • Page 149 Figure 92 – Pitch Angle Adjustment........105 Figure 93 – Omni-Directional Antenna Installation ....106 Figure 94 –Jumper Installation ......... 107 Figure 95 – Fixing Feeder Cables with Feeder Clip ....107 Figure 96 – Single bend........... 107 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 150 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Figure 97 – Multiple Bend ..........108 Figure 98 – Hoisting Trawl ..........109 Figure 99 – Fixing the Feeder Cable ........109 Figure 100 – Drilling the Holes on the Wall......111 Figure 101 –...

  • Page 151: Tables

    Table 8 – DC Output Power Interface Description ....45 Table 9 – ID Numbering Description ........52 Table 10 – DIP Settings for ZXG10-BS30 (V1.5) ....54 Table 11 – Connection Details for ETRM Layer Settings ..56 Table 12 – Connection Details for Single Cabinet....57 Table 13 –...
  • Page 152 ZXG10-BS30 (V1.5) Compact Outdoor BTS Hardware Installation Manual Table 26 – Description for Local Operation and Maintenance Interface ................. 80 Table 27 – Description for Inter – Cabinet HW Interface..80 Table 28 – Description for HW interface ....... 81 Table 29 –...

  • Page 153: Index

    HW interface ...... 80 Tower top amplifier ..... 85 Input main contact point TSME ........ 24 interface ......79 Universal alarm symbols ..2 Internal signal cables... 59 VSWR ......116 Kathrein Azimuth ....102 Confidential and Proprietary Information of ZTE CORPORATION...

Table of Contents