IMO Jaguar VXR3A-1 Quick Reference Manual

Essential Function codes for Quick basic set up
Code Description Default Settings
F01 Frequency Command 0: UP/DOWN keys on Keypad
F02 Operation Method 0: RUN/STOP keys on keypad
F04 Motor Base Frequency 50.0Hz
Motor rated voltage at Base
F05 230 (200v), 400(400v)
Frequency
F11 Motor overload 1-135% inverter rated current
P02 Motor Capacity Nominal Motor power (kw)
P03 Motor rated current *according to inverter capacity

Application specific settings

Code Description Default Settings
F03 Maximum Frequency 50Hz (25.0 -400Hz), sets desired maximum motor speed.
(0 -3600 Seconds), sets time for motor to accelerate
F07 Acceleration Time 6.00 Seconds
(0-3600 Seconds), sets time for motor to decelerate
F08 Deceleration Time 6.00 Seconds
*according to Inverter
F09 Torque Boost (0.0 - 20.0), sets torque boost type for application.
capacity
F15 Frequency Limiter (high) 70.00Hz (0.0 - 400Hz), sets the Frequency upper limit.
F16 Frequency Limiter (low) 0.00Hz (0.0 - 400Hz), sets the Frequency lower limit.
F26 Carrier Frequency 15Khz (0.75 - 15Khz), sets the Motor sound level.
F37 Load Type Selection 1 (Constant Torque) (0-5), sets the load type required for application.
F42 Control Mode Selection 0 (0-4), sets V/f or Torque Vector mode options.
E52 Menu Display Mode 0 (0-2), sets which menus can be accessed.
H69 Automatic Deceleration 0 (0-4), sets deceleration mode for application.
InverterType(VXR)
Output Ratings
Comments/change to:-
Nominal Applied Motor Kw
1: 0-10Vdc input (terminal 12)
2: 0/4-20mA input (terminal C1)
Rated capacity KVA
1: PLC-FWD (run forward) PLC-REV (run
Rated voltage V
reverse)
Rated low PWM Freq. A
Frequency from Motor data plate (Hz)
Current high PWM Freq.A
0: Output voltage ~ supply voltage
80-240v (for 200v rated drives)
Overload capacity A
160-500v (for 400v rated drives)
Input Ratings
Motor rated current from data plate (A)
Min supply capacity KVA
Rated voltage V
Motor rated power from data plate (KW)
MCCB rating with DCR A
Motor rated current from data plate (A)
without DCR A
Fuse rating with DCR A
without DCR A
Cable Sizes
Mains supply with DCR
Comments/change to:-
Mains supply without DCR
Motor cable mm2
Earth cable
0hz to Maximum Frequency.
Braking resistor cable
Unscreened Cable Max
from Maximum Frequency to 0Hz.
Screened cable Length
Braking resistor Ω
Braking resistor W
Cooling Method
Enclosure IP
Weight Kg
Code Explanation
Overcurrent trip during
OC1
acceleration
Overcurrent trip during
OC2
deceleration
Overcurrent trip during steady
OC3
Overvoltage trip during
OU1
acceleration
Overvoltage trip during
OU2
deceleration
Overvoltage trip during steady
OU3
LU Undervoltage protection
Single phase input Three phase input
3A-1 5A-1 8A-1 11A-1 1A5-4 2A5-4 3A7-4 5A5-4 9A-4 13A-4
0.4 0.75 1.5 2.2 0.4 0.75 1.5 2.2 4 5.5
1.1 1.9 3 4.1 1.1 1.9 2.8 4.1 6.8 9.9
Three Phase 200v/50Hz, 200-230v/
Three Phase, 380-415v/50Hz 380-460/60Hz
60Hz
3 5 8 11
1.5 2.5 3.7 5.5 9 13
2.5 4.2 7 10
150% of rated output current for 1 min 150% of rated output current for 1 min
200% of rated output current for 0.5s 200% of rated output current for 0.5s
0.7 1.3 2.4 3.5 0.6 1.1 2 2.9 4.9 7.4
Single Phase 200-240v 50/60Hz Three Phase 380-480v, 50/60Hz
6 10 16 20 6 10 10 15
6 6
10 16 20 32 10 16 20 30
20 20 32 40
2.5 4
4 6
2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5
2.5 4
2.5
50 100 100
30 60 80
100 40 200 160 130 80
200 400 200 400 800
Natural Cooling Fan Cooling Natural Cooling Fan Cooling
IP20 IP20
0.6 0.8 1.7 2.3 1.1 1.2 1.7 1.7 2.3 3.4
Code Explanation Code
L in Input phase loss protection OLU
OPL Output phase loss protection Er1
Overheat protection for
OH1 Er2
speed heat sink communications error
OH2 External alarm input trip Er3
PTC thermistor for motor
OH4 Er6
protection
Overheat protection for braking
dbH Er8 RS485 communications error
speed resistor
Electronic thermal overload Data save error during
OL1 ErF
relay
18A-4 24A-4 30A-4
7.5 11 15
13 18 22
18 24 30
10 15 20
20 30 40
40 50 60
2.5 2.5 2.5
60 40 35
900 1400 1400
3.6 6.1 7.1
Explanation
Overload protection
Memory error
Remote keypad
CPU error
Operation protection
undervoltage