IMO Jaguar CUB3A-1 Quick Reference Manual

Function codes
Essential Function codes for Quick basic set up
Code Description Factory settings
FO1 Freq.reference 4=On-board 1=External 0-10v (max) to terminal 12
source potentiometer 2=External 4-20mA (max) to terminal C1
FO2 RUN/STOP 2=RUN & STOP commands
command source via keypad only
F04 Motor base Frequency 50.0Hz Frequency shown on motor rating plate (Hz)
FO5 Motor rated Volts 0=Motor V=Inverter Voltage shown on motor rating plate (V)
at base frequency Input V at base frequency
F11 Motor overload Nominal rated current of like-sized
4P motor (A)
P02 Motor capacity Nominal motor power (kW) Power shown on motor rating plate (kW)
P03 Motor rated current Rated current of P02 (A) Current shown on motor rating plate (A)
Additional function codes that may be changed for general NT application
Code Description Factory setting
FO3 Max. Frequency 50 Hz Maximum desired motor operating frequency
FO7 Accelerating time 6.00 seconds Required time for motor to accelerate 0Hz to
F08 Decelerating time 6.00 seconds Required time for motor to decelerate from
FO9 Torque boost * F09-0.0 TO 20.0%(Works in conjunction with F37)
F15 Frequency High limit 70.0Hz These values define the output frequency range
for a given input range, ie-0 to 10V input
reference gives 20Hz-45Hz output when
F16 Frequency Low limit 0.0Hz
F26 PWM carrier 15kHz Reducing level gives noisier motor but less RF
frequency interference and lower earth leakage from
F37 Load selector 1 (HT load) F37=0 or 3 (Works in conjunction with F09)
Additional function codes that may be changed for HT application
Code Description Factory setting
FO9 Torque boost *
F37 Load selector 1 (HT load)
But could be F37=1 or 4 (manual Boost)
P09 Motor slip 0.0% Most commonly acts to compensate for
compensation decreasing shaft speed as load increases
Note 1: NT denotes normal or variable torque load such as a fan or centrifugal pump etc.
HT denotes high/heavy or constant torque application, ie - mixer, hoist, screw feeder, p.d. pump, etc.
Note 2: All other settings including: thermistor input, PID control, I/O configuration etc and for further full set
information, please refer to Cub instruction manual.
Note 3: *Factory set value depends upon rated power of Jaguar Cub/ model number.
If in doubt - consult IMO or CUB instruction manual
Technical data
Comments/change to:- Inverter Type (CUB)
Output Ratings
Nominal Applied Motor
1=Terminals only, FWD and REV
Rated voltage
inputs active
Rated low PWM Freq
Current high PWM Freq A
Overload capacity
Input Ratings
Required motor overload level (A)-
Rated voltage
Reduce for smaller motor
Fuse Rating
Rated Current
Cable Sizes
Mains Supply
without DCR
Motor Cable
Comments/change to:-
Earth Cable
Braking resistor cable
(relating to maximum operating speed)
Max Length (m)
Screened Cable
maximum frequency
Braking resistor
Cooling Method
maximum frequency to ØHz
Enclosure
Weight
Note 4: Fuse ratings and rated input currents are typical with no DCR.
Note 5: Fuse and cable ratings are for guidance only. Local practise and regulations must take priority.
F15=45 and F16=20
Alarm codes
motor cable (and vice-versa)
Code
OC1 Overcurrent trip during
OC2 Overcurrent trip during
Comments/change to:-
F09=0.0 (Auto boost)
OC3 Overcurrent trip during
(Works in conjunction with F37)
Best could be F37=2 (Auto boost)
OU1 Overvoltage trip during
(Works in conjunction with F09)
OU2 Overvoltage trip during
OU3 Overvoltage trip during
LU Undervoltage protection
Single phase input Three phase input
3A-1 5A-1 8A-1 11A-1 1A5-4 2A5-4 3A7-4
kW 0.4 0.75 1.5 2.2 0.4 0.75 1.5
V Three Phase 200-230v 50/60Hz Three Phase 380-415v/50Hz 380-460/60Hz
3 5 8 11
1.5 2.5 3.7
2.5 4.2 7 10
A
150% of rated output current for 1 min 150% of rated output current for 1 min
200% of rated output current for 0.5s 200% of rated output current for 0.5s
kW Single Phase 200-240v 50/60Hz Three Phase 380-480v, 50/60Hz
A 10 16 20 32 6 10 10
A 5.4 9.7 16.4 24.8 1.7 3.1 5.9
mm 2
4
mm 2 2.5 2.5 2.5 2.5 2.5 2.5 2.5
mm 2 4
mm 2 2.5
50 50 50 50 50 50 50
Ω
100 40 200
W
200 400 200
Natural Cooling Fan Cooling Natural Cooling
IP IP20 IP20
Kg 0.6 0.8 1.7 2.3 1.1 1.2 1.7
Name Code Name Code
Lin Input phase loss OLU
acceleration protection
OPL Output phase loss Er1
deceleration protection
OH1 Overheat protection Er2
steady speed for heat sink communications error
OH2 External alarm Er3
acceleration input trip
OH4 PTC thermistor for Er6
deceleration motor protection
dbH Overheat protection for Er8
steady speed braking resistor
OL1 Electronic thermal ErF
overload relay
IMO Precision Controls Ltd.
1000 North Circular Road, Staples Corner, London NW2 7JP , United Kingdom
Tel: +44(0)20 8452 6444 Fax: +44(0)20 8450 2274 Email: imo@imopc.com Web: www.imopc.com
5A5-4 9A-4
2.2 4
5.5 9
16 20
8.2 13.0
2.5 2.5
50 50
160 130
400
Fan Cooling
1.7 2.3
Name
Overload protection
Memory error
Remote keypad
CPU error
Operation protection
RS485
communication error
Data save error
during undervoltage

Quick reference guide