Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Gemini 7892 MyMINI
Summary of Contents for Gemini 7892 MyMINI
- Page 1 7892 MyMINI INSTALLATION AND USE MANUAL Made in Italy AC2690UK Rev.10 - 01/14...
-
Page 2: Table Of Contents
CONTENTS USER MANUAL GENERAL ADVICE - OPERATION ALARMS 3.1 - Vehicle position alarm 3.2 - Vehicle start alarm 3.3 - Battery tamper alarm 3.4 - Generic a larm ( yellow-green wire) SUMMARY TABLE OF ALARM MESSAGES - MESSAGE S FROM AND TO THE SYSTEM 5.1 - Initial configuration 5.2 - STOP &... -
Page 3: General Advice
Dear Customer, thank you for purchasing this self-managed MyGTRACK sytem designed and manufactured in Italy by GEMINI Technologies S.p.A. Please read the present manual carefully to fully take advantage of all the security features offered by the system and avoid triggering false alarms which use up your SIM credit. -
Page 4: Alarms
When ignition is switched back ON, the system compares the current position with the position recorded upon last switch-off If they differ (value above the normal tolerance factory set by Gemini and unalterable), the system will send the user an alarm message. -
Page 5: Generic A Larm ( Yellow-Green Wire)
3.4 - GENERIC ALARM (connection of yellow-green wire) ATTENTION Transmission of a generic alarm message is subject to connection of the dedicated wire and system configuration by the installer. When the message is sent, the system checks the alarm source. If still active, it will be inhibited (i.e. -
Page 6: Messages From And To The System
The initial configuration command must be sent to the tracker to notify “password”, system “model” and “number” to which alarm SMS must be forwarded, where: -setup#: configuration command. -password#: password, factory set by Gemini (“000000”, six zeros). ATTENTION The new password must be a 6-digit code and can contain both numbers and letters ( i.e.: AA1234 or aa1234). -
Page 7: Stop & Go Activation Command
ATTENTION The system can be configured with the “STOP & GO” feature (SMS message when ignition is turned ON or OFF, see par. 5.2, 5.3 or 8.0). 5.2 - STOP & GO ACTIVATION COMMAND : setup#password#can#main phone number#new password#emergency phone number#f# Upon reception of SMS, the system replies: setup ok with password= new password. -
Page 8: Engine Stop Activation Command
5.7 - ENGINE STOP ACTIVATION COMMAND: stop#password# At this request, the system sends a confirmation message to the sender. After engine is cut-off (vehicle stopped with GPS speed zero) the system will send an SMS, to both numbers, indicating engine stop and vehicle position (latitude;... -
Page 9: Periodic Position Control Command
5.10 - PERIODIC POSITION CONTROL COMMAND: pos#password#180 This function is only available when the system is armed (by SMS or by configuring the auxiliary input, see par. 5.11 and 5.14). Code “180” indicates the number of minutes after which the system checks vehicle position (selectable between 1 and 999 minutes). -
Page 10: Example Of Mygtrack Management
System Emergency phone version password phone number number by Gemini (optional) When the configuration string is sent, the system replies: Setup ok with password=AA1234 Repeat this operation every time you want to modify your password or phone numbers. ATTENTION The new password must be a 6-digit code and can contain both numbers and letters ( i.e.: AA1234 or aa1234). -
Page 11: Vehicle Parking
7.0 - VEHICLE PARKING The MyGTRACK interacts with the GPS satellite network and the GSM mobile phone network. Two antennas have therefore been installed on your vehicle: one for receiving the GPS signals to locate the vehicle and the other for transmitting the safety information to the user mobile phone, by means of the GSM network In order to guarantee the maximum safety level provided by the system, you must be aware that:... -
Page 12: Message Overview
Indicative value, factory set by Gemini, for the speed limit (expressed (Ref.01) in km/h, always 3 digits Indicative value, factory set by Gemini, for the time interval after which (Ref.02) a message must be sent (expressed in days, always 3 digits . -
Page 13: Installer Manual
INSTALLER MANUAL 10.0 - GENERAL INSTALLATION ADVICE Dear installer, MyGTRACK systems are safety devices that provide full active protection to 12/24V vehicles via GPS location tracking and GSM communication (by mobile phone). IMPORTANT: The MyGTRACK system you are about to install requires special attention when fitting the GPS and the GSM antennas. -
Page 14: Sim Card
11.0 - SIM CARD ATTENTION control unit MUST be POWER ED OFF when you c arry out the following operations. SMALL PIN (max. 2mm diam.) TO EJECT THE SIM CARD TRAY PULL OUT THE SIM CARD TRAY NSERT THE SIM IN TRAY REPLACE THE TRAY MAKING SURE THAT THE “SIM”... -
Page 15: Antenna Connections
12.0 - ANTENNA CONNECTIONS ATTENTION control unit MUST be POWER ED OFF when you c arry out the following operations. GPS ANTENNA GSM ANTENNA (SATELLITE (RECEPTION/TRANSMISSION RECEPTION/TRANSMISSION) BY GSM NETWORK) PLUG THE ANTENNA CONNECTOR IN THE SILVER CONNECTOR, UNTIL IT CLICKS INTO PLACE. -
Page 16: Electrical Connections
ATTENTION Unplug the battery negative before making any electric connection and only reconnect it once all connections have been made. : the available vehicle model specification sheets can be downloaded from: www.gemini-alarm.com (private area POS. WIRE FUNCTION WIRE COLOUR Engine immobilizer NC contact... -
Page 17: System Configuration
Only use manufacturer-specified voltages. Do not clean the unit with water but use a damp cloth to wipe. Do not remove warranty labels. GEMINI TECHNOLOGIES S.p.A. DECLINES ANY LIABILITY FOR DAMAGES TO THE SYSTEM DUE TO IMPROPER USE OR INSTALLATION. -
Page 18: Optical Signals
16.0 - OPTICAL SIGNALS The LED will flash for System initializing approx. 30” System configuration OK Satellite search LED steady ON for (with +15/54) max 20” Satellite reception indication Every 5/7 seconds (with +15/54) Weak GSM field (when engine is turned off) System arming System armed System disarming... -
Page 19: Auxiliary Input Configuration
18.0 - AUXILIARY INPUT CONFIGURATION (YELLOW/GREEN wire) The auxiliary negative input allows for many connections and configurations According to the required connection , program the input (by sending an SMS) as indicated in the table below ATTENTION The system is configured with the YELLOW/GREEN wire active 24/7, negative input enabled to send generic alarm SMS to the 1st preset number. - Page 20 7 Dudley Court , Jessop Close, Clacton-on-Sea, Essex, CO15 4LY TEL: +44 (0) 1255 434353 Email: sales@avsgemini.com | Web: www.avsgemini.com UK Distributors of the Gemini Alarm Systems...