Access Point Mode - TP-Link TL-WR902AC Quick Installation Manual

At Home

Access Point Mode

Internet
Wired Router
A
Range Extender Mode
Internet
Host AP
Client Mode (TV/Game Console Adapter)
Internet
Host AP
Hardware Information
B C
A
OR OR
Smart TV Desktop Other Device
LEDs:
LED Status
On
(Power)
Blinking
On
(Internet)
Off
On
(Wireless) Blinking
Off
On
Off
On
(WPS)
Blinking
Off
D
B
A B
Indication
The router is on.
The router is initializing or being upgraded.
The internet is available.
The internet is unavailable.
The wireless network is enabled.
The router is connecting to the host network
when in Range Extender or Client mode.
The wireless network is disabled.
A USB device is connected.
No USB device is connected.
This light stays on for 5 minutes when a WPS
connection is established, then goes off.
WPS connection is in progress.
No WPS connection is established.
1. Switch the operation mode to AP/Rng Ext/Client and connect the
hardware according to Step A to D in the left diagram.
2. Connect your device to the router wirelessly. The Wi-Fi network
names and password are on the router's label.
3. Launch a web browser and enter http://tplinkwifi.net in the address
bar. Log in with admin (in lowercase) for both username and
password.
4. Click Next to start the Quick Setup.
5. Select Access Point and click Next.
6. Either customize your Network Name and Password for the
2.4GHz/5GHz wireless network or keep the default ones, and then
click Next.
7. Select the LAN type of the router (Smart IP in most cases) and
click Next.
8. Click Finish to apply the settings.
If you have changed the default Wi-Fi name(s) and password(s), you
have to reconnect your wireless devices to the new Wi-Fi network(s).
1. Switch the operation mode to AP/Rng Ext/Client and plug the
router's adapter into an electrical outlet near your host AP.
2. Connect your device to the router wirelessly or via an Ethernet
cable. The Wi-Fi network names and password are on the router's
label.
3. Launch a web browser and enter http://tplinkwifi.net in the address
bar. Log in with admin (in lowercase) for both username and
password.
4. Click Next to start the Quick Setup.
5. Select Range Extender and click Next.
6. Click Connect to connect to the corresponding host network and
enter its password. You can either copy the SSID (network name) of
the host network or customize it, and then click Next.
7. Select the LAN type of the router (Smart IP in most cases) and
click Next.
8. Click Finish to apply the settings.
9. Relocate the router about halfway between your host AP and the
Wi-Fi dead zone.
The extended network shares the same Wi-Fi password as that of your
host network, but may have different wireless network name if you have
customized it during the configuration.
1. Switch the operation mode to AP/Rng Ext/Client and plug the
router's adapter into an electrical outlet near your host AP.
2. Connect your device to the router wirelessly or via an Ethernet
cable. The Wi-Fi network names and password are on the router's
label.
3. Launch a web browser and enter http://tplinkwifi.net in the address
bar. Log in with admin (in lowercase) for both username and
password.
4. Click Next to start the Quick Setup.
5. Select Client and click Next.
6. Click Connect to connect to the corresponding host network and
enter its password. Then click Next.
7. Select the LAN type of the router (Smart IP in most cases) and
click Next.
8. Click Finish to apply the settings.
9. Connect your wired-only device to the router via an Ethernet cable.
Buttons and Ports:
Ports Description
This button is used to switch the operation
Mode Switch
mode of the router.
This port functions as the WAN port in Router
WAN/LAN
mode and as the LAN port in Hotspot, Access
Point, Range Extender and Client mode.
Power The port is used to connect the power adapter.
To reset the router, use a pin to press and hold
RESET
the button for about 5 seconds.
This port is used to plug a 3G/4G modem or a
USB disk into.
(WPS) To establish WPS connection, press this button.
©2017 TP-Link