Deprag MINIMAT 389730 A Operating Instruction Booklet

Stationary screwdriver spindle

Advertisement

Quick Links

012554EN
Operating Instruction Booklet
Stationary Screwdriver Spindle
344-340-31
344-440-31
344-740-31
344-840-31
MINIMAT
389730 A
389730 B
389730 C
389730 D

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MINIMAT 389730 A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Deprag MINIMAT 389730 A

  • Page 1 012554EN Operating Instruction Booklet Stationary Screwdriver Spindle 344-340-31 389730 A 344-440-31 389730 B 344-740-31 389730 C 344-840-31 389730 D MINIMAT...
  • Page 2: Table Of Contents

    We kindly ask that you read these operating instructions carefully so that you will be able to use this tool safely and for many years to come. If you need additional information, please contact your DEPRAG Representative, one of our international support offices or us direct at DEPRAG.
  • Page 3: Safety Tips

    Safety Tips 1.1 General Safety Tips Before operating tool make sure to carefully read and observe this operating instruction. Generally, the operator of the equipment and/or machinery is responsible for the equipment’s perfect condition and operation, while observing all necessary safety regulations.
  • Page 4: General Safety Tips For Pneumatic Stationary Screwdriver Spindles

    1.2 General Safety Tips for Pneumatic Stationary Screwdriver Spindles · Disconnect the tool from the air supply, when changing bits or when re-adjusting clutch. · Do not wear wide clothing or jewelry, for they can be seized by movable parts. Wear a hairnet if operator has long hair. ·...
  • Page 5: Operator Obligation

    1.4 Operator Obligation Personnel, who is engaged in the operation of the equipment, must always be committed to · observe the basic safety and accident preventing regulations, · read and observe the safety and warning notifications of this operating instruction booklet. 1.5 Warranty and Liability Unless otherwise specified, our “General Sales and Delivery Conditions”...
  • Page 6: Symbol Description

    1.6 Symbol Description Read and observe the Operating Instruction Booklet, prior to and during operation of tool. DANGER Reference to an immediate danger to a person. May lead to serious injuries or even death, if unobserved! Properly recycle environmentally damaging grease, cooling agents or detergents.
  • Page 7 Maintenance and repair on hydraulic and pneumatic equipment may only be performed by specially trained personnel! Disconnect equipment from air supply, prior to repair of pneumatic or hydraulic equipment. Provide regular preventive maintenance on hoses and airlines. Exchange hose lines, even if there is no visible damage! (Observe corresponding requirements of the manufacturer!) After repair and maintenance, check the following items: ·...
  • Page 8: Observe Environmental Regulations

    1.7 Observe Environmental Regulations When working on or with the equipment, it is imperative to observe all requirements in regards to waste-disposal and proper recycling. Especially during installation, repair or maintenance, water damaging agents such as · lubricating grease and oil ·...
  • Page 9: Installation

    The hose length should not exceed 2 meters. · All DEPRAG Screwdrivers may be operated either with or without lubricated air (see paragraph: Maintenance and Upkeep). Best results are achieved, when machine is lubricated with 1 – 2 drops of oil per 1m...
  • Page 10 OUR RECOMMENDATION: The preferred lubricating method for the screwdriver spindles mounted in fixtures, brackets, machines, etc., each in connection with a controller, is method b) with Point-of-Use Oiler. · Check pressure at directly on the machine. The Regulator needs to be adjusted to an airflow between 5.0 (71 PSI) and 6.3 bar (90 PSI).
  • Page 11: Operation

    Adjust clutch to the required torque value. If necessary, exchange clutch spring. The necessary torque adjustment can be tested, using a DEPRAG Torque Wrench or Dynamometer (see DEPRAG catalogs D3020 and D3022). This equipment can also be used to re-adjust the torque of the Screwdriver Spindle.
  • Page 12: Range And Exchange Of Clutch Spring

    4.1 Range and Exchange of Clutch Spring The torque range of the DEPRAG Screwdriver is adjustable. Please see a listing for the torque ranges of the color-coded springs below. Torque Range of the individual clutch spring: Type 344-340-31 und 344-440-31 "...
  • Page 13: Torque Adjustment

    claw of the clutch clutch spring half-round bore hex of the clutch shaft adjustment nut Picture: Exchange of Clutch Spring Attention: The claw of the clutch must engage with the claw of the spindle (located in clutch bearing). The hex of the clutch shaft must engage with the hex of the spindle (located in gearing).
  • Page 14: Change Of Bits

    4.3 Change of bits Depending on the additional mounting parts (clutch bearing etc.) 4.4 Connection-Possibilities of the Function Control Use as air pressure outlet during screw-assembly: · to control driver start and stop, as well as shut-off control of clutch; ·...
  • Page 15: Assembly - Disassembly

    After repair or maintenance, verify that equipment runs to specification! Principally, use only DEPRAG original spare parts. Otherwise, a reduction in equipment power-output and an increased maintenance-requirement occurs. If NON-DEPRAG parts are installed, DEPRAG is justified to void any existing warranty and liability obligations. Attention:...
  • Page 16 Pull off air connecting-side bearing cover from rotor. f. Press the two ball bearings from the bearing covers. Assembly: Use the DEPRAG Grease 807293 (100-g tube) to grease the ball bearing, needle bearing and gearing parts prior to reassembly.
  • Page 17: Spare Parts Drawing

    5.1 Spare Parts Drawing...
  • Page 24: Installation Tips For Screwdriver Spindle

    5.2 Installation Tips for Screwdriver Spindle...
  • Page 26: Maintenance And Upkeep

    6 months (single shift). · Exchange broken or worn inserting tools immediately, for they can cause injury to the Operator. · If tool malfunctions, we recommend to send the machine to DEPRAG. 6.1 Wear Parts UANTITY...
  • Page 27: Trouble Shooting

    Valve Pin is too long Check length of valve pin, either shorten or replace valve pin (pic- ture: Actual Size of Valve Pin) Piston 3804692 caught Disassembly and cleansing of in sleeve 3783221 parts If necessary, please send tool to DEPRAG for service.
  • Page 28: Delivery Capacity

    Picture: Actual Size of Valve Pin Attention: When connecting to compressed air supply valve pin may be catapulted out which may cause serious injuries. When verifying the actual size of the valve pin, make sure N O T to hold the screwdriver directed towards yourself or any other person.
  • Page 29: Accessories - Optional Equipment

    Accessories - Optional equipment Exhaust connection cpl. 351820 R Exhaust connection cpl. 351820 U Please mount the exhaust connection # 351820 R / U as follows: Disconnect the screwdriver from the air supply. Clamp screwdriver spindle on its housing by means of chucking jaws into a vice.
  • Page 30 INFORMATION You will find suitable inserting tools · in our brochure D 3320 E or · on the internet as follows: ® Screwdriving www.deprag.com Technology® Selection program: Inserting tools...
  • Page 31: Storage

    10 Storage Unused machines should be stored in a dry, locked area. 11 Technical Data Manufacturer DEPRAG SCHULZ GMBH u. CO. Address Kurfürstenring 12 - 18 Postfach 1352 D-92224 Amberg D-92203 Amberg Phone 09621/371-0 09621/371-120 Technical Data: 344-340-31 344-440-31 344-740-31 344-840-31...
  • Page 32: Disposal

    12 Disposal Unused machines should be stored in a dry, locked area. Disassemble the machine for the required disposal complete. Observe local and environmental regulations for the separation and recycling of materials. Recycle waste oil to avoid environmental contamination! Waste Oil...
  • Page 33: Declaration Of Manufacturer

    13 Declaration of Manufacturer EC-Declaration of Manufacturer in accordance with the CE-Machine-Guideline 98/37/EC, appendix II B DEPRAG SCHULZ GMBH u. CO. Kurfürstenring 12 – 18 Postfach 1352 D-92204 Amberg D-92203 Amberg declares, that the construction of the stationary screwdriver spindle...
  • Page 34: Service Locations And Authorized Partners

    14 Service Locations and Authorized Partners ALGERIA CZECHIA/SLOWAKIA GREAT BRITAIN EP-Technology Trading S.U.A.R.L. DEPRAG CZ a.s. DEPRAG Ltd. 29 Rue Ahmed Tlili - ZI Borj Cedria ul. T.G. Masaryka 113 Unit B4, Pegasus Court TN-2055 Bir el Bey Tunis - Tunisia CZ -50781 Lázně...
  • Page 35 Tel.: +1 / 972 / 221 – 8731 Toma Zupana 16 LUXEMBOURG Fax: +1 / 972 / 221 – 8163 SLO-4202 NAKLO Toll Free: (800) 4 DEPRAG Tel.: +386 (0) 4 / 277 17 00 Internet: http://www.deprag.com Parelhoenstraat 24 Fax: +386 (0) 4 / 277 17 17 e-mail: deprag@depragusa.com...
  • Page 36 DEPRAG SCHULZ GMBH u. CO. Postfach 1352, D-92203 Amberg Kurfürstenring 12-18, D-92224 Amberg (09621) 371-0 (09621) 371-120 Internet: http://www.deprag.com e-mail: info@deprag.de...

Table of Contents