Makita DGA700 Instruction Manual
Cordless angle grinder
Hide thumbs
Also See for DGA700:
- Instruction manual (157 pages) ,
- Instruction manual (112 pages) ,
- Instruction manual (89 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Makita DGA700
Summary of Contents for Makita DGA700
- Page 1 INSTRUCTION MANUAL Cordless Angle Grinder DGA700 DGA900 Read before use.
-
Page 2: Specifications
Symbols Vibration mined according to EN60745: use. Model DGA700 Work mode: surface grinding with normal side grip Read instruction manual. Work mode: surface grinding with anti vibration side grip Work mode: disc sanding with normal side grip or less... -
Page 3: Ec Declaration Of Conformity
WARNING: carrying, pulling or unplugging the power tool. use of the power tool can differ from the declared Keep cord away from heat, oil, sharp edges Damaged or entangled cords tool is used. increase the risk of electric shock. WARNING: When operating a power tool outdoors, use an extension cord suitable for outdoor use. - Page 4 nated battery packs. When battery pack is not in use, keep it away coins, keys, nails, screws or other small metal terminal to another. tacts eyes, additionally seek medical help. It is an employer's responsibility to enforce Do not use a battery pack or tool that is dam- ments by the tool operators and by other per- sons in the immediate working area.
- Page 5 Threaded mounting of accessories must match For example, if an abrasive wheel is snagged or the grinder spindle thread. For accessories entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. hardware of the power tool will run out of balance, operator, depending on direction of the wheel’s move- break under these conditions.
- Page 6 Make sure the wheel is not contacting the Cutting-Off Operations: workpiece before the switch is turned on. Before using the tool on an actual workpiece, Overstressing the wheel wobbling that could indicate poor installation or a poorly balanced wheel. or binding of the wheel in the cut and the possibil- form the grinding.
-
Page 7: Functional Description
Follow your local regulations relating to dis- posal of battery. SAVE THESE INSTRUCTIONS. while sliding the button on the front of the cartridge. CAUTION: Only use genuine Makita batteries. charger. CAUTION: Always install the battery cartridge fully until the red indicator cannot be seen. If not,... - Page 8 Indicating the remaining battery capacity Only for battery cartridges with the indicator When the tool is operated in a manner that causes it to 1. Indicator lamps 2. Check button tool off and stop the application that caused the tool to light up for a few seconds.
- Page 9 Shaft lock Automatic speed change function Press the shaft lock to prevent spindle rotation when installing or removing accessories. 1. Mode indicator 1. Shaft lock Mode indicator status Operation mode NOTICE: High speed mode Switch action CAUTION: Before installing the battery car- tridge into the tool, always check to see that the depending on the work load.
- Page 10 ASSEMBLY CAUTION: Always be sure that the tool is Installing side grip (handle) CAUTION: Always be sure that the side grip is installed securely before operation. 1. Wheel guard 2. Bearing box 3. Screw guard Loosen the nut, and then pull the lever in the direction of the arrow.
- Page 11 1. Wheel guard 1. Lock nut 2. Depressed center wheel 3. Inner 4. Mounting part the wheel guard with fastening the nut. Be sure to that the spindle cannot revolve, then use the lock nut 1. Lever 2. Nut 1. Lock nut wrench 2. Shaft lock dure in reverse.
-
Page 12: Operation
Grinding and sanding operation Optional accessory 15° 1. Sanding lock nut 2. 3. Rubber pad workpiece. In general, keep the edge of the wheel or disc at an Mount the rubber pad onto the spindle. angle of about 15° to the workpiece surface. During the break-in period with a new wheel, do not Fit the disc on the rubber pad and screw the sand- ing lock nut onto the spindle. - Page 13 1. Lock nut 2. 1. Wire cup brush wheel 3. 4. Wheel guard for abrasive cut-off wheel / diamond wheel For Australia and New Zealand brush onto spindle and tighten with supplied wrench. ø45 NOTICE: brush. ø78 Operation with wire wheel brush Optional accessory CAUTION: Check operation of wire wheel...
-
Page 14: Maintenance
NOTICE: using wire wheel brush. breakage. vents start to become obstructed. MAINTENANCE CAUTION: Always be sure that the tool is before attempting to perform inspection or maintenance. NOTICE: alcohol or the like. Discoloration, deformation or cracks may result. Battery guard 1. -
Page 15: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool spec- Side grip Depressed center wheel / Flap disc Rubber pad Sanding lock nut Wire wheel brush Wire cup brush Lock nut wrench Dust cover attachment... - Page 16 J an- B apt i s t Vi nk s t r aat 2, M ak i t a E ur ope N . V. 3070 K or t enber g, B el gi um 3- 11- 8, S um i y os hi - c ho, M ak i t a C or por at i on A nj o, A i c hi 446- 8502 J apan 885578-228...