Download Print this page

Advertisement

INSTRUCTION MANUAL
Angle Grinder
GA7060
GA7060R
GA9060
GA9060R
DOUBLE INSULATION
Read before use.

Advertisement

   Summary of Contents for Makita GA7060

  • Page 1

    INSTRUCTION MANUAL Angle Grinder GA7060 GA7060R GA9060 GA9060R DOUBLE INSULATION Read before use.

  • Page 2

    AG systems of between 220 V and 250 V Work mode: disc sanding with normal side grip Only for model GA7060 / GA9060 h, DS Switching operations of electric apparatus cause volt- Work mode: disc sanding with anti vibration side grip...

  • Page 3

    Work mode: disc sanding with anti vibration side grip standard or standardized documents: EN60745 h, DS available from: Model GA9060 Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium Work mode: surface grinding with normal side grip 17.6.2015 h, AG Work mode: surface grinding with anti vibration side grip...

  • Page 4

    When operating a power tool outdoors, use an Maintain power tools. Check for misalignment extension cord suitable for outdoor use. Use of or binding of moving parts, breakage of parts a cord suitable for outdoor use reduces the risk of and any other condition that may affect the electric shock.

  • Page 5

    cracks, tear or excess wear, wire brush for entering into the pinch point can dig into the surface of loose or cracked wires. If power tool or acces- the material causing the wheel to climb out or kick out. sory is dropped, inspect for damage or install an undamaged accessory.

  • Page 6

    Be careful not to damage the spindle, the Cutting-Off Operations: lock nut. Damage to these parts could result in Do not “jam“ the cut-off wheel or apply exces- wheel breakage. sive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel Make sure the wheel is not contacting the workpiece before the switch is turned on.

  • Page 7

    For tool with the lock-on switch FUNCTIONAL CAUTION: Switch can be locked in "ON" posi- DESCRIPTION tion for ease of operator comfort during extended use. Apply caution when locking tool in "ON" CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.

  • Page 8

    The indication lamp lights up green when the tool is Installing or removing wheel guard plugged. If the indication lamp does not light up, the mains cord The indication lamp is lit but the tool does not start even / abrasive cut-off wheel, diamond wheel) worn out, or the controller, the motor or the ON/OFF Unintentional restart proof...

  • Page 9

    1. Wheel guard 2. Bearing box 3. Screw 4. Lever 1. Lock nut 2. Depressed center wheel 3. Inner 4. Mounting part wheel guard with fastening the screw. Be sure to tighten that the spindle cannot revolve, then use the lock nut 1.

  • Page 10

    CAUTION: Never switch on the tool when it is in contact with the workpiece, it may cause an Optional accessory injury to operator. Only for tools with M14 spindle thread. CAUTION: Always wear safety goggles or a face shield during operation. CAUTION: After operation, always switch off the tool and wait until the wheel has come to a...

  • Page 11

    For Australia and New Zealand Operation with abrasive cut-off / diamond wheel ø45 Optional accessory ø78 WARNING: When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. WARNING: NEVER use cut-off wheel for side ø78...

  • Page 12

    Operation with wire wheel brush NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. Optional accessory CAUTION: Check operation of wire wheel Air vent cleaning brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel The tool and its air vents have to be kept clean.

  • Page 13

    OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool spec- Side grip Depressed center grinding wheel / Flap disc Abrasive cut-off wheel / Diamond wheel Rubber pad Abrasive disc Sanding lock nut Wire wheel brush...

  • Page 16

    Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan 885467B227 www.makita.com 20150826...

This manual also for:

Ga9060, Ga7060r, Ga9060r

Comments to this Manuals

Symbols: 0
Latest comments: