Page 2
LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for three years from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling.
Table of Contents Title Page Introduction ..............1 How to Contact Fluke ..........2 Safety Information ............3 Product Familiarization ..........9 Use the Product ............12 Measure AC and DC Voltage ........12 Measure Resistance and Continuity......13 Measure Microamps μA .......... 14 Measure Temperature ..........
Introduction The Fluke 902 FC is a hand-held battery-operated HVAC True-rms Clamp Meter (the Product) that measures: • AC current • DC current (up to 200 μA for flame rod testing through input terminals) • AC and DC voltages •...
HVAC True-rms Clamp Meter Safety Information Safety Information A Warning identifies conditions and procedures that are dangerous to the user. A Caution identifies conditions and procedures that can cause damage to the Product or the equipment under test. XWWarning To prevent possible electrical shock, fire, or personal injury: •...
Page 8
902 FC Users Manual • Do not exceed the Measurement Category (CAT) rating of the lowest rated individual component of a Product, probe, or accessory. • Comply with local and national safety codes. Use personal protective equipment (approved rubber gloves, face protection, and flame-resistant clothes) to prevent shock and arc blast injury where hazardous live conductors are exposed.
Page 9
HVAC True-rms Clamp Meter Safety Information • Limit operation to the specified measurement category, voltage, or amperage ratings. • The battery door must be closed and locked before you operate the Product. • Remove all probes, test leads, and accessories before the battery door is opened.
Page 10
When batteries are changed, ensure that the calibration seal in the battery compartment is not damaged. If damaged, the Product may not be safe to use. Return the Product to Fluke for replacement of the seal. • Do not use in CAT III or CAT IV environments without the protective cap installed.
Page 11
HVAC True-rms Clamp Meter Safety Information Table 1 lists the symbols used on the Product and in this manual. Table 1. Symbols Symbol Description Consult user documentation. WARNING. RISK OF DANGER. WARNING. HAZARDOUS VOLTAGE. Risk of electric shock. Application around and removal from uninsulated hazardous live conductors is permitted.
Page 12
902 FC Users Manual Table 1. Symbols (cont.) Symbol Description Measurement Category III is applicable to test and measuring circuits connected to the distribution part of the building’s low-voltage MAINS installation. Measurement Category IV is applicable to test and measuring circuits connected at the source of the ...
HVAC True-rms Clamp Meter Product Familiarization Product Familiarization Figure 1 and Table 2 show the features of the Product. iad01.eps Figure 1. Product Features...
Page 14
902 FC Users Manual Table 2. Product Features Item Description Fluke Connect Jaw release Tactile barrier Jaws Hold button Rotary switch: AC and DC voltage Resistance and continuity DC microamps ...
Page 15
HVAC True-rms Clamp Meter Product Familiarization Table 3 shows the items on the display. Table 3. Display iad06.eps Item Description Battery is low and should be changed Indicates the presence of high voltage ID number Indicates minimum or maximum recording mode ...
HVAC True-rms Clamp Meter Use the Product The chosen voltage mode shows on the display. Measure the voltage by touching the probes to the correct test points of the circuit. Read the measured voltage on the display. Note When a measured voltage is above 30 V, shows on ...
902 FC Users Manual Measure the resistance by touching the probes to the desired test points of the circuit. Read the measured resistance on the display. Note If the resistance is <30 , the continuity beeper sounds and indicates a short circuit.
Page 19
HVAC True-rms Clamp Meter Use the Product Gas Burner Controller Gas Burner Controller Burner iad04.eps Figure 2. Test a Flame Rod...
902 FC Users Manual Measure Temperature The Product measures temperature in either Celsius (°C) or Fahrenheit (°F). XW Warning To prevent possible electrical shock, fire, or personal injury, do not touch voltages >30 V ac rms, 42 V ac peak, or 60 V dc.
Page 21
HVAC True-rms Clamp Meter Use the Product Vent Pipe 80BK Integrated Temperature Probe (Type K) iad05.eps Figure 3. Measure Temperature...
902 FC Users Manual Measure Capacitance Turn off power to the circuit. Disconnect and discharge the capacitor. Turn the rotary switch to Take the measurement noting the correct polarity of the capacitor. If the capacitor requires more discharging, diSC shows while the capacitor discharges.
Page 23
HVAC True-rms Clamp Meter Use the Product Tactile Barrier Currents Cancel iad03.eps Figure 4. Proper AC Current Measurement...
902 FC Users Manual Backlight Push to toggle the backlight on and off. The backlight automatically turns off after 2 minutes. To disable the automatic backlight timeout: Hold and turn on the Product. Push . MIN MAX Recording Mode The MIN MAX recording mode captures the minimum and maximum input values.
HVAC True-rms Clamp Meter Use the Product Display HOLD In the Display HOLD mode, the Product freezes the display. The Product also beeps every 4 seconds and flashes to remind the user. XW Warning To avoid possible electric shock or personal injury, do not use the HOLD function to measure unknown potentials.
902 FC Users Manual Maintenance XW Warning To prevent possible electrical shock, fire, or personal injury: • Have an approved technician repair the Product. • Use only specified replacement parts. Clean the Product XW Warning To prevent possible electrical shock, fire, or personal injury, remove the input signals before you clean the Product.
When batteries are changed, ensure that the calibration seal in the battery compartment is not damaged. If damaged, the Product may not be safe to use. Return the Product to Fluke for replacement of the seal. • Repair the Product before use if the battery leaks.
Page 28
902 FC Users Manual To replace the batteries (see Figure 5): Turn the rotary switch to OFF. Remove the test leads from the terminals. Loosen the battery door fastener and remove the door from the case bottom. Remove the batteries.
4696918 TL75 Test lead set 4306653 80BK Thermocouple set, K-type 1997234 Softcase 1997276 Fluke Connect Figure 6 shows how to use Fluke Connect with the Product. Fluke Connect Bluetooth ® Connection to FC Tools FC Module SAVE Fluke Connect Connect...
902 FC Users Manual Specifications Electrical Specifications Function Range Resolution Accuracy Voltage DC 600 V 0.1 V 1.0 % ±5 counts Voltage AC 1.5 % ±5 counts, 600 V 0.1 V (True-rms) (45 Hz to 400 Hz) 2.0 % ±5 counts, (45 Hz to 65 Hz) 2.5 % ±5 counts,...
HVAC True-rms Clamp Meter Specifications General Specifications -10 °C to +50 °C Operating Temperature -30 °C to +60 °C, without batteries Storage Temperature installed Non condensing (<10 °C) ≤90 % RH (10 °C to 30 °C) Operating Humidity ≤75 % RH (30 °C to 40 °C) ≤45 % RH (40 °C to 50 °C) Operating Altitude 2000 meters above mean sea level...
Page 32
902 FC Users Manual Power Requirements Two AA Batteries, IEC LR6 Electromagnetic Compatibility (EMC) International IEC 61326-1: Portable Electromagnetic Environment; IEC 61326-2-2; CISPR 11: Group 1, Class A Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the internal function of the equipment itself.