Specifications - Makita GA9010C Instruction Manual

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Switch trigger
2-2. Lock lever
3-1. Side grip
4-1. Wheel guard
4-2. Screw
4-3. Bearing box
5-1. Wheel guard
5-2. Bearing box
5-3. Nut
5-4. Lever
6-1. Nut
6-2. Lever
7-1. Lock nut

SPECIFICATIONS

Depressed center wheel diameter
Max. wheel thickness
Rated speed (n) / No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
from sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model GA7010C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Model GA9010C
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Explanation of general view
7-2. Depressed center wheel/Multi disc
7-3. Inner flange
8-1. Lock nut wrench
8-2. Shaft lock
9-1. Lock nut
9-2. Abrasive disc
9-3. Rubber pad
11-1. Wire cup brush/Wire bevel brush
12-1. Lock nut
12-2. Abrasive cut-off wheel/
diamond wheel
12-3. Inner flange
12-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
Model
Spindle thread
)
0
Overall length
Net weight
Safety class
) : 90 dB (A)
pA
) : 101 dB (A)
WA
) : 91 dB (A)
pA
) : 102 dB (A)
WA
GA7010C
180 mm
8,400 min
453 mm
4.3 kg
ENE048-1
Vibration
ENF002-2
The vibration
determined according to EN60745:
Model GA7010C
Work mode : surface grinding
Vibration emission (a
ENG905-1
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Model GA9010C
Work mode : surface grinding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : disc sanding
Vibration emission (a
Uncertainty (K) : 1.5 m/s
4
13-1. Lock nut
13-2. Outer flange 78
13-3. Abrasive cut-off wheel/
diamond wheel
13-4. Inner flange 78
13-5. Wheel guard for abrasive cut-off
wheel/diamond wheel
14-1. Exhaust vent
14-2. Inhalation vent
15-1. Commutator
15-2. Insulating tip
15-3. Carbon brush
16-1. Screwdriver
16-2. Brush holder cap
6.5 mm
M14
-1
/II
Wear ear protection
total value (tri-axial
) : 9.5 m/s
h,AG
2
) : 2.5 m/s
h,DS
2
) : 9.5 m/s
h,AG
2
) : 2.5 m/s
h,DS
2
GA9010C
230 mm
M14
-1
6,000 min
453 mm
4.5 kg
ENG900-1
vector sum)
2
2
2
2