Philips SD-5.31SL Service Manual page 27

Error Error text
code
8120 DAC Low Power Standby Off OK
8121 DAC Low Power Standby Off I2C bus busy
8122 DAC Low Power Standby Off I2C failed
8200 DAC Upsample 192k OK
8201 DAC Upsample 192k I2C bus busy
8202 DAC Upsample 192k I2C failed
8220 DAC Upsample 96k OK
8221 DAC Upsample 96k I2C bus busy
8222 DAC Upsample 96k I2C failed
8240 DAC UpSample On OK
8241 DAC UpSample On bus busy
8242 DAC UpSample On I2C failed
8260 DAC UpSample Off OK
8261 DAC UpSample Off bus busy
8262 DAC UpSample Off I2C failed
5.12.2 Basic Engine Nuclei
Error
code Error text
3900 Test successful
3901 "Parity error from Basic Engine to Serial"
3902 "Unexpected response from Basic Engine"
3903 "Communication time-out error"
3904 "Basic Engine returned error number 0xXX"
3921 "Parity error from Basic Engine to Serial"
3922 "Unexpected response from Basic Engine"
3923 "Communication time-out error"
3924 "Basic Engine returned error number 0xXX"
3800 Test successful
3801 "Parity error from Basic Engine to Serial"
3802 "Unexpected response from Basic Engine"
3803 "Communication time-out error"
3804 "Basic Engine returned error number 0xXX"
3805 "Focus loop could not be closed"
3820 Test successful
3821 "Parity error from Basic Engine to Serial"
3822 "Unexpected response from Basic Engine"
3823 "Communication time-out error"
3824 "Basic Engine returned error number 0xXX"
4200 Test successful
4201 "Parity error from Basic Engine to Serial"
4202 "Unexpected response from Basic Engine"
4203 "Communication time-out error"
4204 "Basic Engine returned error number 0xXX"
4205 "Sledge could not be moved to home
position"
4206 "Focus loop could not be closed"
4207 "Motor not on speed within time-out"
4208 "Radial loop could not be closed"
4209 "PLL could not lock in accessing or tracking
state"
4210 "Subcode or sector information could not be
read"
4211 "Requested subcode item could not be
found"
4212 "TOC could not be read in time"
4213 "Seek could not be performed"
4220 Test successful
Test Instructions Mono Board SD5.31SL SD-5.31SL
Error
code Error text
4221 "Parity error from Basic Engine to Serial"
4222 "Unexpected response from Basic Engine"
4223 "Communication time-out error"
4224 "Basic Engine returned error number 0xXX"
4225 "Sledge could not be moved to home
position"
4226 "Focus loop could not be closed"
4227 "Motor not on speed within time-out"
4228 "Radial loop could not be closed"
4229 "PLL could not lock in accessing or tracking
state"
4230 "Subcode or sector information could not be
read"
4231 "Requested subcode item could not be
found"
4232 "TOC could not be read in time"
4233 "Seek could not be performed"
4240 Test successful
4241 "Parity error from Basic Engine to Serial"
4242 "Unexpected response from Basic Engine"
4243 "Communication time-out error"
4244 "Basic Engine returned error number 0xXX"
4245 "Sledge could not be moved to home
position"
4246 "Focus loop could not be closed"
4247 "Motor not on speed within time-out"
4248 "Radial loop could not be closed"
4249 "PLL could not lock in accessing or tracking
state"
4250 "Subcode or sector information could not be
read"
4251 "Requested subcode item could not be
found"
4252 "TOC could not be read in time"
4253 "Seek could not be performed"
4000 Test successful
4001 "Parity error from Basic Engine to Serial"
4002 "Unexpected response from Basic Engine"
4003 "Communication time-out error"
4004 "Basic Engine returned error number 0xXX"
4005 "Radial loop could not be closed"
4020 Test successful
4021 "Parity error from Basic Engine to Serial"
4022 "Unexpected response from Basic Engine"
4023 "Communication time-out error"
4024 "Basic Engine returned error number 0xXX"
4400 Test successful
4401 Test successful
4100 Test successful
4101 "Parity error from Basic Engine to Serial"
4102 "Unexpected response from Basic Engine"
4103 "Communication time-out error"
4104 "Basic Engine returned error number XX"
4120 Test successful
4121 "Parity error from Basic Engine to Serial"
4122 "Unexpected response from Basic Engine"
4123 "Communication time-out error"
4124 "Basic Engine returned error number XX"
5. EN 27