Page 5
Continued 12. Reference Information 12.1 Tool for Troubleshooting 12-1 12.2 Acronyms and Abbreviations 12-2 12.3 The Sample Pattern for the Test 12-3 12.4 Wireless LAN 12-4...
High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably trained and qualified service engineer. (2) Use only Samsung replacement parts There are no user serviceable parts inside the printer. Do not make any unauthorized changes or additions to the printer, these could cause the printer to malfunction and create electric shock or fire haz-ards.
Take care not to cut or damage the power cable or plugs when moving the machine. (9) Use caution during thunder or lightening storms. Samsung recommend that this machine be disconnected from the power source when such weather conditions are expected. Do not touch the machine or the power cord if it is still connected to the wall socket in these weather conditions.
1.2.4 Assembly / Disassembly Precautions Replace parts carefully, always use Samsung parts. Take care to note the exact location of parts and also cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer. (5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable. Service Manual Samsung Electronics...
2. Be sure to replace the battery with the same or equivalent type recommended by the manufacturer. 3. Super capacitor or Lithium batteries contain toxic substances and should not be opened, crushed, or burned for disposal. 4. Dispose of used batteries according to the manufacture’s instructions. Service Manual Samsung Electronics...
70,000 Pages Fuser Unit 80,000 Pages Device Memory Standard / Max. 64MB / 192MB(Std./Max) 92MB / 192MB(Std./Max) Type SDRAM SDRAM Expand Memory Slot , Type SDRAM DIMM Expand Memory specification would be defined separate note. Compression Technology Service Manual Samsung Electronics...
Page 13
600x300dpi Photo 600x300dpi Other FOOT Stand by Less than 8.5 sec ( From Ready ) From Cold Less than 31.5 seconds Status Copy Speed/ SDMC at all 30cpm/Ltr, 28cpm/A4 SDMC: Single Letter mode Document Multiple Copy Service Manual Samsung Electronics...
Page 14
Book Button (Same as Rocky) 1-Touch Dial 30EA Speed Dial 200 locations Total locations can be stored TAD I/F Tone/Pulse Selectable in Tech mode Pause Auto Redial Last Number Redial Distinctive Ring Caller ID External Phone Interface Service Manual Samsung Electronics...
Page 15
1 Group Dial Fax Forward Yes(On/Off), both Sent and Received Broadcasting up to 239 locations Cover page Delayed fax Yes (Tx only) Memory RX Voice Request N/A Functions Polling Earth/Recall Auto Reduction Yes (On,Off) F/W Remote Service Manual Samsung Electronics...
Page 16
Memory Back-up Yes, Max. 72hours NETWORK Option No (Default) Protocol TCP/IP(LPR, Standard TCP/ TCP/IP(LPR, Standard IP Printing, Samsung Port, TCP/IP Printing,Samsung IPP), NetWare Port, IPP), NetWare, Ethertalk Operating System Microsoft Windows 98/ME/2000/XP/2003,Microsoft Windows NT 4.x, 5.x, 6.x,Mac OS 10.3 and abover...
MB : System Working Memory Area and Scan Buffer MB : FAX Memory Receive Area MB : Printing System Working Memory Area - Max Frequency : 166MHz - Store Fax Receive Memory Data by using Battery Service Manual Samsung Electronics...
Page 20
The exit motor driving circuits is formed when the driver IC is selected. The AN44060A Motor Driver IC is used in this case. The resistance Rs value for sensing and voltage value for the V reference can be changed by motor driving voltage value. Service Manual Samsung Electronics...
3.1.3.1 Feeding Section Feeding Method : Universal Cassette Type Feeding Standard : Center Loading Feeding Capacity : Cassette 250 Sheets (75g/ , 20lb StandardPaper) 3.1.3.2 Transfer Ass’y In Warranty( Life time) : Within 70,000 sheets printing Service Manual Samsung Electronics...
Page 22
45 sec at Warm up Over Heat Error over for 10 sec or 240 over for 5 sec Low Heat Error Standby :130 below for 10 sec Printing : 35 below for 7 sec at consecutibve 2 page printing. Service Manual Samsung Electronics...
Page 23
In spite of steady rotation of Polygon Motor, No the generation of the Hsync signal 3.1.3.6 Scanner( ADF) 3 in 1 : SCX-5330N 4 in 1 : SCX-5530FN Scanning Method: Color CCD(600 x 1200 dpi) Scan speed : SDMP 28cpm/MDSP 20cpm Service Manual Samsung Electronics...
Page 24
3.1.3.7 Toner Cartridge OPC Cleaning :Mechanical Cleaning by the cleaning blade. The recycled toner : Trash room for the recycled toner No shutter for protecting the OPC Drum Cleaning Roller = -380V -1.35KV 200V Cleaning Blade +4.2kV Service Manual Samsung Electronics...
Page 25
System Overview 3.1.3.8 Duplex Unit Duplex printing function as factory option Available Paper : Letter, Oficio, Legal, Folio, and A4 3.1.3.9 Optional Tray (SCF) For customer covenience in managing paper Capacity : 250 sheets Service Manual Samsung Electronics...
Feeding Pressure (Cassette) : 250~320 gf 250~320 gf Paper Exit Type: Face Down Feed roller Velocity: Feed-roller Cassette; 182.34 mm /sec Feed-roller Frame; 180.42 mm /sec Feed Roller Material: Feed-roller Cassette; EPDM 13.7 mm Feed-roller Frame; EPDM 14.2 mm Service Manual Samsung Electronics...
Page 27
55 Motor : 888.75 rpm(711 pps) - PM 42 Motor : 1156 .25rpm(1850 pps) It is a power delivery unit by gearing: BLDC 62 Motor ->Pickup/Feeder/Developer - PM 55 Motor -> Fuser/Exit - PM 42 Motor -> Duplex Service Manual Samsung Electronics...
Page 28
- Horizontal: 3 0.022 or less in Vision System Orthogonality : SPEC : 1.0 mm or less 3.2.4.3 Acoustic Noise Warming Up: 49dB or less Printing : 54dB or less Copying : 55dB or less Stand-by : 39dB or less Service Manual 3-10 Samsung Electronics...
Page 29
0.05(Coating incl., Crown 0.05~-0.15) Material : AL(AL5052) + PFA Coating Thickness : 0.9mm Coating Material : PFA 100% Coating Thickness : 20um (Thickness after abrasion) GND Type : H/R Bearing Grounding type By SECC Fuser lower frame Service Manual 3-11 Samsung Electronics...
Page 30
- 3st protecting device : Thermostat cuts off the power Safety device - The power of Fuser is cut-off after front cover is open - The overheating safety device for customer - The surface temperature of the Fuser Cover is under 80 Service Manual 3-12 Samsung Electronics...
Page 31
Pitch Error Neighbor line Max 10 Pitch error in sub scanning direction within image height of -105 ~ +105 range Within 6 lines Max 20 within image height of -105 ~ +105 range Service Manual 3-13 Samsung Electronics...
Page 32
Acoustical noise 45dB at normal operation condition, measuring at 1 m horizontal, 0.75m vertical apart Temperature +10 ~ +50 Humidity 30 ~ 80 % Preservation Temperature -20 ~ +60 Humidity 10 ~ 90 % Size Service Manual 3-14 Samsung Electronics...
- Driver : Gear Driver (in a direction opposed to D/R) - Sponge Density : 0.45 , 0.1 g/ - Life : 8,000 sheets or more 3.2.7.4 REGULATING BLADE Type : Regulating toner layer by pressure Valid Length : 228mm Voltage : -420V ~ -600V Service Manual 3-15 Samsung Electronics...
Page 34
- OD : 12.0 0.05 mm - Shaft OD : 6 + 0 / -0.05 mm - Driver : Gear Driver - Roller life : 8,000 sheets or more Roller Voltage : -1.25 ~ -1.70 KV Service Manual 3-16 Samsung Electronics...
Page 35
- CX86710 (SFX336): Existing Modem Chip which adds SSD (System Side Device) for interfacing between LSD and DIB of FM336Plus Core - CX20493 (LSD) : LIU (Line Interface Unit) Chip which is controlled by SSD and satisfies each PSTN Requirements by modulating internal Configuration with connecting Tel Line. Service Manual 3-17 Samsung Electronics...
Page 36
Digital speaker output to monitor received signal Two16-byte FIFO data buffers for burst data transfer with extension up to 255 bytes V.21 Channel 1Flag detect V.21 Channel 1Flag detect +3.3V only operation Typical power consumption Normal mode: 264 mW Service Manual 3-18 Samsung Electronics...
Page 37
After transferring data from SSD, RSP is transferred and LSD recognizes RSP and change LSD to output Driver transfer Data to SSD. DIB Data form SSD to LSD by Transformer has Differential structure of 180 phase difference between DIBP and DIBN for Noise Robustness Service Manual 3-19 Samsung Electronics...
Page 38
Ring detection Current : 20mA 100mA (condition : Voltage=40Vrms,Frequency=20Hz) product Margin : over 15mA 3) False Ring Sound Ring Frequency : 750 Hz + 1020 Hz Ring interrupt Cycle : On/Off depending on input Ring Signal Cycle. Service Manual 3-20 Samsung Electronics...
Page 39
Micom part, Matrix part and LCD. (2) Micom controller Micom has ROM, RAM, I/O Port built-in and displays and lights LCD by CPU command of Main Control Part and report Key recognition Data to Main Control Board. Service Manual 3-21 Samsung Electronics...
Page 40
-Toner Low Sensor: None -Toner Low Indicator: Message displayed on LCD -Cartridge Missing Indicator: Message displayed on LCD Paper Sensing: -Tray: Add Paper message displayed on LCD -MP Tray: Add Paper message displayed on LCD Service Manual 3-22 Samsung Electronics...
Page 41
-Copy image :(max) A4 600dpi pixel processing NAND Flash - 8/16 Bits, H/W ECC Generation Controller - Auto Boot Mode (using internal SRAM, 4KB) - 10M/100Mbps - Full IEEE 802.3 compatibility IEEE1284 compliant parallel port interface Graphic Execution Unit Service Manual 3-23 Samsung Electronics...
Page 43
System Overview Service Manual 3-25 Samsung Electronics...
Page 44
400 Locations (46 digits maximum per location) On-hook Dial (manual fax): Last Number Redial: Automatic Redial: Pause: Yes (using Redial key) Ringer Volume: Off, Low, Medium, High Tone/Pulse: Selectable (Tech Mode Only no Telecom certification for Pulse mode) Service Manual 3-26 Samsung Electronics...
Page 45
- Output Voltage Rising Time : 50 ms Max - Output Voltage Falling Time : 50 ms Max - Output Loading range : 10 M ~ 1000 M - Output Control Signal (BIAS-PWM) : the CPU is HV output when PWM is low. Service Manual 3-27 Samsung Electronics...
Page 46
- Rated Frequency : 50/60 Hz - Frequency Fluctuating range : 47 ~ 63 Hz - Input Current : Under 4.0Arms / 2.0Arms (But, the status when e-coil is off or rated voltage is inputted/outputted ) Service Manual 3-28 Samsung Electronics...
Page 47
Shut down or Output shortage and Protection Voltage Drop overflowing current ITEM System Stand-By Less than 150W PRINTING Less than 400W Sleep-Mode Less than 11W Fuse 24V Fuse 24V Fuse 5V Fuse 5V Fuse 5V Fuse 5V Service Manual 3-29 Samsung Electronics...
Page 48
Triac (Q501) feature : 24A-LV model / 16A-HV model, 600V SWITCHING Phototriac Coupler (PC501) - Turn On If Current : 15mA 50mA(Design: 16mA) - High Repetive Peak Off State Voltage : Min 600V Service Manual 3-30 Samsung Electronics...
AD converter. The voltage value for impressing to the transfer roller is decided by the changed value. Service Manual 3-31 Samsung Electronics...
Page 50
In case of Over Heat Error, no heat is supplied to the fixing unit. When a specified time is elapsed, the engine detects a present temperature again. If the present temperature is a specified degree lower than the memorized temperature, the error is recovered. Service Manual 3-32 Samsung Electronics...
Page 51
LSU Error Recovery: If the LReady or Hsync error happens, the paper exits out beforehand. The engine mode is changed to recovery mode and the engine informs the main system of the engine mode. And the engine checks the LSU error. If the error doesn t happen, the printing job will be proceeding. Service Manual 3-33 Samsung Electronics...
Host. 2. Kernel that control and management the whole procedure include of Control flow and Printing Job before transfer to Engine system. Service Manual 3-34 Samsung Electronics...
4. Port Monitor that manages the network communication between spooler and Network Interface Card, or various additional application and Network Interface Card,(this is, at first, make communication logical port, manage the data, transfer them from spooler to network port, and offer the result of printing). Service Manual 3-35 Samsung Electronics...
Page 54
Engine print the received data to required paper with the sequential developing process. The additional printing function are realized in (1) Web environment (2) Window environment. On addition, Kernel informs a status of printing status and printer status to user made printing job with the Status Monitor. Service Manual 3-36 Samsung Electronics...
This chapter describes the main functions for service, such as the product maintenance method, the test output related to maintenance and repair, DCU using method, Jam removing method, and so on. It includes the contents of manual. 4.1 Control Panel 4.1.1 SCX-5530FN Service Manual Samsung Electronics...
Page 56
Alignment and Adjustments Alignment and Adjustments 4.1.2 SCX-5330N Service Manual Samsung Electronics...
1. Remove any remaining pages from the ADF. 3. Pull the jammed paper gently out of the ADF. 2. Open the ADF cover. ADF cover 4. Close the ADF cover. Then load the removed pages, if any, back into the ADF. Service Manual Samsung Electronics...
Page 59
2. Pull the tray 1 open. 4. Insert the tray 1 into the machine until it snaps into place. Printing automatically resumes. Service Manual Samsung Electronics...
Page 60
3. Pull the tray 1 half. 4.3.5 In the multi-purpose tray 1. If the paper is not feeding properly, pull the paper out 2. Open and close the front cover to resume printing. of the machine. Service Manual Samsung Electronics...
Page 61
If you do not see the jammed paper or if there is any resistance when you pull, stop and go to the next If you still do not see the paper, go to the next step. step. 3. Open the rear cover. Service Manual Samsung Electronics...
Page 62
9. Return the lever, door, stopper, and guide to their orig- inal position. 10. Close the rear cover. Printing automatically resumes. Service Manual Samsung Electronics...
Page 63
2. Remove the jammed paper from the duplex unit. 3. Pull the jammed paper out. If the paper does not come out with the duplex unit, remove the paper from the bottom of the machine. Service Manual Samsung Electronics...
2. Press OK when Machine Setup appears. 3. Press the Scroll buttons until Language appears and press OK. 4. Press the Scroll buttons until the language you want appears and press OK. 5. Press Stop/Clear to return to Standby mode. Service Manual 4-10 Samsung Electronics...
2. Press OK when Machine Setup appears. 3. Press the Scroll buttons until Clock Mode appears and press OK. 4. Press the Scroll buttons to select the other mode and press OK. 5. Press Stop/Clear to return to Standby mode. Service Manual 4-11 Samsung Electronics...
Page 66
2. Press the Scroll buttons until you hear the volume you want. 3. Press On Hook Dial to save the change and return to Standby mode. Note : You can adjust the speaker volume only when the telephone line is connected. Service Manual 4-12 Samsung Electronics...
You can insert a pause while you are setting up speed buttons or speed dial numbers. To insert a pause, press Redial/Pause at the appropriate place while entering the telephone number. A - appears on the display at the corresponding location. Service Manual 4-13 Samsung Electronics...
3. Press the Scroll buttons until Scan PWR Save appears and press OK. 4. Press the Scroll buttons until the time setting you want appears and press OK. 5. Press Stop/Clear to return to Standby mode. Service Manual 4-14 Samsung Electronics...
3. Press the Scroll buttons until Job Timeout appears and press OK. 4. Press the Scroll buttons until the time setting you want appears and press OK. 5. Press Stop/Clear to return to Standby mode. Service Manual 4-15 Samsung Electronics...
Pause Time Dram Test Configuration Dial Mode Rom Test Key History Modem Speed Pattern Test Error Info Error Rate Shading Test Usage Page Component Check Clear All Mem Service Support Clear Counts Flash Upgrade Silence Time Service Manual 4-16 Samsung Electronics...
Brazil France Oman Italy Poland Spain Bangladesh Austria Kuwait Netherlands Moroco Belgium Algeria Country Portugal Pakistan Sweden Norway Bahrain Denmark Srilanka Finland Saudi Arabia Switzerland Chile Greece Peru Ireland Argentina Turkey Hungary Romania Bulgaria Czech Service Manual 4-17 Samsung Electronics...
1. sending and receiving fax must be the same model. 2. A sending fax must be set up as ECM mode, and a receiving memory must be set up as 100%. If not, the function operates abnormally Service Manual 4-18 Samsung Electronics...
Page 73
4) Scroll to Shading Test and Enter. 5) Select Shading&Print appears on the bottom line and press Enter. 6) Your machine picks up the paper and adjusts the shading value. 7) After adjusting, shading value will be printed with graphic image. Service Manual 4-19 Samsung Electronics...
Page 74
1. sending and receiving fax must be the same model. 2. A sending fax must be set up as ECM mode, and a receiving memory must be set up as 100%. If not, the function operates abnormally Service Manual 4-20 Samsung Electronics...
Page 75
MFP before any RDS function can be re- attempted. If no activity is detected on a connected call for a maximum duration of 5 minutes (300 seconds), the call will be released / disconnected from the MFP-side. Service Manual 4-21 Samsung Electronics...
3. After the scan, CCD SHADING PRO- FILE will be print out. 4. If the printed image is different to the image, the CCD is defect. NOTICE : When you test CCD, make sure that the cover is closed. Service Manual 4-22 Samsung Electronics...
Use this list to check for send and receive errors. If a communication error occurs while the machine is in TECH mode, the protocol list will print automatically. OTHER ITEM This list provides a list of the user system data settings and tech mode settings. Component Check Service Manual 4-23 Samsung Electronics...
Page 78
42.Dev Bias Test control for HVPS is normal or not. Dev Bias On(Off) 43.THV EN/NEG Test THV EN/NEG On(Off) 44.THV ON(1300V) THV On(Off) 45.THV ADC 1300V ADC value displayed. 46.THV ADC 600V~3500 ADC value displayed. Service Manual 4-24 Samsung Electronics...
Press 1( in the number keypad) : The LCD display shows "Updated date" Press 2( in the number keypad) : The LCD display shows "Product first use date" < Display > OS 1 . 00 . 86 . 07 11-31-2005 Service Data 2004-1-11 Service Manual 4-25 Samsung Electronics...
The cycle period given below is for reference only. COMPONENT REPLACEMENT CYCLE ADF Rubber Pad 20,000 Pages ADF Roller 60,000 Pages Pick-up Roller 150,000 Pages Transfer Roller 70,000 Pages Fuser 80,000 Pages Tray Rubber Pad 150,000 Pages Service Manual 4-26 Samsung Electronics...
Black spot Supply Roller 53.2mm Horizontal density band Develop Roller 39.2mm Horizontal density band Transfer Roller 47.1mm Black side contamination/transfer fault Heat Roller 88.9mm Black spot and fuser ghost Pressure Roller 101.3mm Black side contamination Service Manual 4-27 Samsung Electronics...
Alignment and Adjustments 4.9 Display LED and Error Messages 4.9.1 Display LED The Status LED on the control panel shows the status of your machine. See the table below to know your machine’s status. Service Manual 4-28 Samsung Electronics...
Messages and their meanings are listed in alphabetical order. Note : When you call for service, it is very convenient to tell the service representative the display mes- sage. Messages in the colored cells are available only with SCX-5530FN. Service Manual 4-29 Samsung Electronics...
Page 84
Alignment and Adjustments Service Manual 4-30 Samsung Electronics...
Page 85
Alignment and Adjustments Service Manual 4-31 Samsung Electronics...
Page 86
Alignment and Adjustments Service Manual 4-32 Samsung Electronics...
Page 87
Alignment and Adjustments Service Manual 4-33 Samsung Electronics...
Page 88
Alignment and Adjustments Service Manual 4-34 Samsung Electronics...
3. Unplug the power cord. 4. Use a flat and clean surface. 5. Replace only with authorized components. 6. Do not force plastic-material components. 7. Make sure all components are in their proper position. Service Manual Samsung Electronics...
Page 90
Upper Right and pull it in the direction of arrow, as shown below. ADF Ass'y Cover Upper Right 2. Apply light pressure to the left side of the Cover Upper Left and pull it in the direction of arrow, as shown below. Cover Upper Left Service Manual Samsung Electronics...
Toner Cartridge Cassette 2. Open the Cover. 4. To remove the Front Cover, first pull the part below the both side of the Front Cover with a light pressure to the direction of arrow. Front Cover Service Manual Samsung Electronics...
Page 92
Ass'y and pull it in the direction of arrow, as shown below. MP Tray Ass'y MP Tray Ass'y 2. Pull the Tray Links from the both side of the Front Cover with a light pressure to the direction of arrow. Tray Link Service Manual Samsung Electronics...
2. Remove the four screws securing the Rear Cover and then Release the Rear Cover from the Set. 4. Unlatch the Face Up Cover from the Rear Cover and then release the Face Up Cover, as shown below. Rear Cover Face Up Cover Service Manual Samsung Electronics...
Page 94
5. Remove the two screws securing the both side of the securing the Thermostat and remove it. Electrode and then release the Caps and Electrodes in the direction of arrow, as shown below. Thermostat CON Harness Electrode REC Harness Electrode Service Manual Samsung Electronics...
Page 95
9. Remove the three screw securing the Fuser Cover and release the Fuser Cover from the Fuser Frame. 7. Unplug the connector from the Input Guide and remove the one screw securing the Thermistor and Fuser Cover remove it. Thermister Fuser Frame Service Manual Samsung Electronics...
Page 96
Guide Input in the direction of arrow, as shown below. Jam Holder Guide Input Hook Notice : You must remove the Guide Input before removing the Jam Holder so that you won't damaged Pressure Roller. Service Manual Samsung Electronics...
Page 97
3. Apply light pressure to the bottom of the Right Side Cover and pull it to the right side in the direction of arrows, as shown below. Left Side Cover Right Side Cover Service Manual Samsung Electronics...
Page 98
Disassembly and Reassembly 6. To remove the DIMM Cover, first open the DIMM Cover in the direction of arrow and then release the DIMM Cover, as shown below. DIMM Cover Service Manual 5-10 Samsung Electronics...
5. Remove the nine screws securing the OPE PBA to the OPE Cover. 3. Apply light pressure to the front of the OPE Unit and pull it in the direction of arrow, as shown below. OPE Cover OPE Unit Cover OPE PBA Service Manual 5-11 Samsung Electronics...
Page 100
Mode Onetouch Menu Tel_Copy 7. Remove the Lens and Keys from the OPE Cover. 9. For easy disassembly, release the Battery-NIH. Battery-NIH Mode Onetouch Copy Menu LED Lens Stop Clear Black On Hook Start Black Service Manual 5-12 Samsung Electronics...
Page 101
4. Remove the Open Cover, as shown below. Open Cover ADF Ass'y Notice : When working on the ADF Motor Ass'y take care not to contaminate any of the rubber surfaces with grease. Service Manual 5-13 Samsung Electronics...
Page 102
Ferrite Core and the Motor Harness routing. When refitting the ADF Engine part ensure that the Harness and Ferrite are properly located and are clear of the Motor Fan and White Bar Clip. Service Manual 5-14 Samsung Electronics...
Page 103
2. Remove the two screws securing the Platen Ass'y, as shown below. 5. Remove the four screws securing the Scan Upper. 3. Remove the one screw securing the Ground Cable and unplug the four connectors and CCD Cable. ADF Ground Cable Service Manual 5-15 Samsung Electronics...
Page 104
7. Remove the CCD Cable, as shown below. and lift from the pulleys, as shown below. Belt Spring CCD Cable Core Notice: You should connector remove the CCD Cable vertically to avoid the CCD Cable pin damage. Service Manual 5-16 Samsung Electronics...
Page 105
Scan Motor Ass'y ADF Lower Harness 11. If necessary, remove the two screws securing the Scan Motor and remove it, as shown below. 13. Unplug the connector from the Open Sensor Ass'y. Gear Bracket Ass’y Scan Motor Service Manual 5-17 Samsung Electronics...
Page 106
CCDM as is possible, as shown below. 2) When refitting the Scan Upper Cover take care to ensure that the Cover Open Switch is not trapped. CCD Holder Service Manual 5-18 Samsung Electronics...
Page 107
Ass'y and remove it. Flat Cover Flat Motor OPE Panel Shield Controller Ass’y USB Host Cartridge LSU_5V Thermistor Network MPF_SEN Port REGI Port Pick Up BLDG Parallel Port Engine Duplex Motor SCF Con Modem PBA Service Manual 5-19 Samsung Electronics...
Page 108
Shield and unplug the Film Cable and then Shield and unplug the connector from the Modem remove the Modem PBA. PBA and then remove the Speaker. Film Cable Shield Modem PBA Shield Speaker Service Manual 5-20 Samsung Electronics...
Page 109
Drive Ass'y base plate. When refitting the Drive Ass'y tighten the screws the order they are numbered. Only screws numbered 1 to 5 are fitted at this stage. Screw 6 is fitted when the Shield Controller Ass'y is refitted. Service Manual 5-21 Samsung Electronics...
Page 110
- Side Cover Right (Refer to 5.7.3) 2. Unplug the connector from the Connection PCB and remove the three screws securing the Duplex Drive Unit and remove it. Harness Bracket Ass’y Connection Duplex Motor Duplex Motor Duplex Drive Ass'y Service Manual 5-22 Samsung Electronics...
Page 111
Shield SMPS (With AC Inlet) 2. Unplug the two connectors (HVPS, Fuser). AC Inlet Connector SMPS Insulator Sheet Fuser Connector HVPS Connector 3. Remove the three screws securing the Shield SMPS Ass'y and remove it. Shield SMPS Ass’y Service Manual 5-23 Samsung Electronics...
Page 112
- Side Cover Right (Refer to 5.7.3) Fuser Exit Motor, Duplex Fan 2. Unplug the all connectors. Duplex Motor FAN MAIN HVPS Connection 3. Remove the two screws securing the Connection PCB and remove it. Connection Service Manual 5-24 Samsung Electronics...
Page 113
- Side Cover Right (Refer to 5.7.3) Fuser Exit Bracket Ass'y 2. Unplug the connector from the Connection PCB. Step Motor Connection Harness Fuser Drive 3. Remove the three screws securing the Fuser Drive Ass'y and remove it. Fuser Drive Ass’y Service Manual 5-25 Samsung Electronics...
Page 114
- Side Cover Right (Refer to 5.7.3) pull the Fans (Main, Duplex). 2. Unplug the two connectors from the Connection PCB, as shown below. Duplex Fan Connection Main Fan Main Fan Duplex Fan (Fuser Exit Motor) Service Manual 5-26 Samsung Electronics...
Page 115
2. To remove the Pick Up Roller Ass'y, first lift the notch attached to the Pick Up Roller Ass'y from the Shaft, then slide the Pick Up Roller Ass'y from left to right and it will be released completely, as shown below. Pick Up Roller Ass'y Service Manual 5-27 Samsung Electronics...
Page 116
2. Remove the two screws securing the Duplex Guide Housing. Feed Roller Bushing Duplex Guide Housing 3. Unplug the one connector (Photo Interrupter) and remove the Duplex Guide Housing (with Feed Roller), as shown below. Photo Interrupter Connector Duplex Guide Housing Service Manual 5-28 Samsung Electronics...
2. Remove the eight screws securing the HVPS Housing, as shown below. HVPS Insulator Sheet Shield HVPS Housing 3. Unplug the connector for connector PBA and SMPS first. Unplug the other Connections. Duplex Motor Engine Connection PBA & SMPS Duplex Guide Housing Service Manual 5-29 Samsung Electronics...
2. Remove the four screws securing the Cover Mid Front remove: and release two hooks in the center. This cover is - Middle Cover Ass'y (Refer to 5.21) fragile take care when removing it. Hook Hook Cover Mid Front Service Manual 5-30 Samsung Electronics...
MPF Housing Stopper Idle MP Pick Up Ass'y MPF Housing Notice : Do not grab the rubber part of the Feed1 Roller, it may cause a malfunction due to a foreigen object. Service Manual 5-31 Samsung Electronics...
5. Remove the three screws securing the Feed Bracket Unit and then remove the Feed Bracket Unit and Feed2 Shaft. Feed Bracket Unit 3. Pull up the Feed Idle Shaft and the Bushs (with Spring). Feed Idle Shaft Spring Bush Feed2 Shaft Service Manual 5-32 Samsung Electronics...
Page 121
Notice : Do not grab the rubber part of the Feed1 Roller, 7. Remove the Clutch Unit, as shown below. it may cause a malfunction due to a foreigen object. Clutch Unit Feed1 Gear Ass'y Feed Shaft Service Manual 5-33 Samsung Electronics...
- Middle Cover Ass'y (Refer to 5.21) Bearing Exit Roller Rack Roller Exit F/Down Exit Gear Notice : Do not grab the rubber part of the Feed1 Roller, it may cause a malfunction due to a foreigen object. Service Manual 5-34 Samsung Electronics...
Terminals, as - Middle Cover Ass'y (Refer to 5.21) shown below. - LSU (Refer to 5.27) CRUM2 PBA Terminal Notice : Be aware of the Terminals to ensure they are not lost. Service Manual 5-35 Samsung Electronics...
Page 124
TR Holder Notice : Do not grab the rubber part of the Transfer Roller, it may cause a malfunction due to a foreigen object. Hole the both side of the Transfer Roller when replacing it. Service Manual 5-36 Samsung Electronics...
- Power Module error OP Panel - Main PBA error - LCD Panel error Refer to Indicate Ready or Error Massage Error Massage Power save <Chapter 4.8> Test Print printing Refer to "Solution Quality is of Image Problem" Nomal? Service Manual Samsung Electronics...
Shaft-Pickup. shaft-pickup and housing-pickup become open or is broken away. 4. If the paper feeds into the printer and Jam 0 occurs, perform Component Test Mode to check feed-sensor of the engine board. Service Manual Samsung Electronics...
Page 127
3. Remove the jammed paper after disas- sembling the fuser : Clean the surface of the pressure roller with dry gauze. • Remove the toner particles stained on the rib. • Check the assemblage and perfor- mance of the exit. Service Manual Samsung Electronics...
Page 128
2. If there is heavy background, repair it by the background troubleshooting method. 3. Clean the surface of the heat roller with IPA or water. 4. Check the warp or separation of the print claw and the holder plate claw, and then manage it. Service Manual Samsung Electronics...
1. Replace the contaminated or damaged part. aged. 2. Check if the document sensors of ADF Ass’y 2. If you cannot confirm the damaged part with the (3 paper sensors) are normal. naked eye, try to replace the ADF Ass’y. Service Manual Samsung Electronics...
2. Confirm to catch a click sound, while a key on the OPE 2. Even after the key has been replaced, it is still wrong, panel is pressed on. try to replace the OPE Ass’y and the Main B'd in sequence. Service Manual Samsung Electronics...
Check and Cause Solution 1. Bending or deformation of the actuator of the paper sen- 1. Replace the defective actuator. sor. 2. The function of the Main PBA is defective Perform. 2. Replace the Main PBA. Service Manual Samsung Electronics...
Page 132
Check and Cause Solution Check the Connector(CN1) and Circuit of the Cover Switch 1. Check the insertion of the Door S/W Connect. department in the Main PBA. 2. Replace the Main PBA or Door Open S/W. Service Manual Samsung Electronics...
Page 133
1. Replace the power supply cord or SMPS. 2. Check for defective of LCD-Panel on the front-cover if the 2. Replace the control board. LCD of Panel does not appear after normal warming-up. 3. Replace the LCD-panel. Service Manual Samsung Electronics...
Page 134
Check and Cause Solution 1. If the supply of +24v is unstable in the Main Control board 1. Replace LSU. linking with LSU, check drive by Engine Test Mode. 2. Replace the Main Control board. Service Manual 6-10 Samsung Electronics...
Page 135
3. When duplex unit relationship life time became all. 3. Check an operation of a feed roller and a registration roller. If they are worn or defective replace them. 4. Replace a Duplex unit. Service Manual 6-11 Samsung Electronics...
4. No. 4. : Open the front cover and check odically at the top of a black image. ribs that corresponds to the position of the voids. Remove if found. 5. If the problems are not solved, replace the developer cartridge. Service Manual 6-12 Samsung Electronics...
Page 137
1, take measures as to replace the develop- er cartridge and try to print out. 5. Clean the inside of the set against the paper particles and foreign matter in order not to cause the trouble. Service Manual 6-13 Samsung Electronics...
Page 138
Digital Printer the bad contacts between power supply in the side of the Developer and charge terminal of HVPS. 3. If steps 1 and 2 above did not correct the problem, replace the HVPS . Service Manual 6-14 Samsung Electronics...
3. The up-to-down movement of the trans- 3. Clean the busing on the transfer roller. fer roller is swift? 4. The HVPS is normal? 4. Replace the HVPS. (Perform Engine Test Mode diagnostic code 4) Service Manual 6-15 Samsung Electronics...
Page 140
Select 'Thick Mode' on paper type menu from mal paper or transparencies such as OHP, the software application and after use, we rec- Digital Printer higher transfer voltage is required. ommend returning to the original Mode. Digital Printer Digital Printer Digital Printer Service Manual 6-16 Samsung Electronics...
Page 141
2. If the transfer roller is contaminated, run PC on the face of page will occur. Cleaning Mode Print 2 or 3 times. Digital Printer And perform Self-Test 2 or 3 times to remove contamination. Service Manual 6-17 Samsung Electronics...
Page 142
Mode diagnostic Mode code 0 if the Solenoid is normal. 3. If not solved by the above directions 1-2, Replace the engine board. 4. Turn the power off, clear the print job on the computer, and try printing again. Service Manual 6-18 Samsung Electronics...
3. Check the connection of HARNESS between the 3. The problem still persists, then replace the LIU and the LIU and the Main PBA. main B'd in sequence. Notes: Product supports the MF DIAL type only. Service Manual 6-19 Samsung Electronics...
Page 144
2. Check the RECEIVE condition by trying to forward a FAX to another fax machine from the forwarding side FAX. 3. Check if the telephone line connected to the Product is contaminated or gets stripped off or down. Service Manual 6-20 Samsung Electronics...
Page 145
Solution Check if the RECEIVE Mode is TEL MODE or FAX Even when the RECEIVE Mode is changed to FAX MODE. MODE, it cannot receive, then replace the LIU and the Main B'd in sequence. Service Manual 6-21 Samsung Electronics...
Page 146
1. If the RECEIVE Mode is set to the TEL MODE, reset it MODE. to the FAX MODE. 2. Even after the RECEIVE Mode is changed to the FAX Mode, it cannot receive, then try to replace the LIU and the Main B'd in sequence. Service Manual 6-22 Samsung Electronics...
Black page is printed out when Copy. Check and Cause Solution 1. Check the CCD problem in Main PBA. 1. Check the CCD harness contact. 2. Check shading profile. 2. Remake shading profile in the tech mode. Service Manual 6-23 Samsung Electronics...
Page 148
1. Remake shading profile in the tech mode. 2. The gap above 0.5 mm can cause a blurred image. 2. Check the gap between original and scanner glass. 3. See “Print” troubleshooting. 3. Check printing quality. Service Manual 6-24 Samsung Electronics...
2. Check if the resolution is set too low in PC Scan 2. If the resolution is set to low, let the user be acquaint- options. (Refer to User's Manual.) ed with the using method well. Service Manual 6-25 Samsung Electronics...
6.8 Toner Cartridge Service It is not guaranteed for the default caused by using other toner cartridge other than the cartridge supplied by the Samsung Electronic or caused by non-licensed refill production. 6.8.1 Precautions on Safe-keeping of Toner Cartridge Excessive exposure to direct light more than a few minutes may cause damage to the cartridge.
Page 151
(1)Check whether foreign sub- stances or toner are stuck to the terminal (contact point) of the developer. (2)Check whether the state of the terminal assembly is normal. 3. If it cannot be recycled: Replace the developer. Service Manual 6-27 Samsung Electronics...
Page 152
2 times. (2) Check whether the state of (2) If toner nearly being expired the terminal assembly is are collected to use, it is normal. judged as the recycled devel- oper. Service Manual 6-28 Samsung Electronics...
Page 153
Clean the terminals of the (point of contact) of the developing roller, then recheck it. developer and the state of assembly. (Especially check the devel- oping roller terminal.) Service Manual 6-29 Samsung Electronics...
The name of printer is displayed empty while 1.Check the protocol of your PC and install DLC/LLC or IPX/SPX protocol. adding a port and the printer doesn’t function. 2.Assign IP Address to PortThru using the front panel. Service Manual 6-30 Samsung Electronics...
An IP address should be assigned to upgrade the Firmware. But upgrading is not executed. Make sure that IP address is entered in Print Server. If an IP address is not entered,reassign it and try again. Service Manual 6-31 Samsung Electronics...
Page 156
Services ’in Control Panel, delete the “sammon.dll” file in the system32 directory of Windows NT, start spooler service and reinstall it. ‘Unable to add the Port list of Samsung ports’ Verify that your PC restarts after installing SyncThru. message appears, when you add a port.
- 250 sh Paper Input / 150 sh Paper Output - 33.6 Kbps Fax Modem (5530FN only) - Duplex Print (5530FN only) - Direct USB Connectivity 2nd Version (PDF Direct Printing) (5530FN only) - Small Foot Print - Toner: 4K(Initial)/ 8K(sales) Service Manual Samsung Electronics...
Service Parts List(SCX-6322DN/XAZ) Service(SA:service available, SNA:service not avaialble) Drawer# Description SEC_Code QT'y Service 8.1-0 22 PPM FLATBED MFP SCX-6322DN/XAZ 8.1-1-1 ELA HOU-SCANNER JC96-04180X 8.1-2 MEA UNIT-COVER PA EX JC97-01556C 8.1-2-1 PMO-TRAY EXT MP NE JC72-00354D 8.1-2-2 PMO-COVER PAPER EXIT JC72-00786C 8.1-3 MEA UNIT-CASSETTE JC97-01736D...
Page 216
Service(SA:service available, SNA:service not avaialble) Drawer# Description SEC_Code QT'y Service 8.1-40-3 PMO-BUSH JC72-40228A 8.1-40-4 PMO-HOLDER GND TR JC72-00883A 8.1-41 MEA UNIT-HOLD GEAR ASS'Y JC97-01573A 8.1-41-1 SPRING ETC-TR_R JC61-70906A 8.1-41-2 PMO-BUSH JC72-40228A 8.1-41-3 PMO-HOLDER GEAR TR JC72-00884A 8.1-44 PMO-CAM JAM REMOVE JC72-00799A 8.1-45 PMO-LOCKER DEVE...
Page 217
Service(SA:service available, SNA:service not avaialble) Drawer# Description SEC_Code QT'y Service 8.4-34-4 ICT-INSERT SHAFT JB70-00154A 8.4-34-5 PMO-PULLEY JB72-00763A 8.4-34-6 PMO-HOLDER BELT JB72-00764A 8.4-34-7 RING-E 6044-000125 8.4-34-8 ELA HOU-CCD MODULE JC96-02759B 8.4-34-9 BELT-TIMING GEAR 6602-001084 8.4-34-11 HOLDER-M-CCD(UMAX) JC61-00703A 8.4-34-12 SPRING ETC-EXIT JB61-70939A 8.4-34-13 IPR-BRK SCAN BD JC70-00228A...
Page 218
Service(SA:service available, SNA:service not avaialble) Drawer# Description SEC_Code QT'y Service 8.7-10 MEA UNIT-HINGE(MCK2) JC97-01839A 8.7-11 PLATE-P-DUMMY PLATEN JC61-00819A 8.7-12 SPRING ETC-CHARGE JC61-70925A 8.7-13 SPRING ETC-TORSION DOC (CC2-F) JB61-00076A 8.8-0 ELA HOU-DADF SUB JC96-02973B 8.8-1 MEA UNIT-COVER OPEN JC97-01844B 8.8-1-1 COVER-OPEN JC63-00195B 8.8-1-2 PMO-STOPPER EXIT...
Page 219
Service(SA:service available, SNA:service not avaialble) Drawer# Description SEC_Code QT'y Service 8.8-33 CBF HARNESS-DADF_GND JC39-00334A 8.8-34 ROLLER-DUPLEX JC66-00589A 8.8-36 GUIDE-DUPLEX_INNER JC61-00737B 8.8-37 GUIDE-DUPLEX_LOWER JC61-00735B 8.8-38 MEA UNIT-GUIDE DUPLEX JC97-01843A 8.8-39 MEA UNIT-GUIDE_P UP JC97-01847B 8.8-39-1 GUIDE-PICK_UP_UPPER JC61-00733B 8.8-39-2 MEA UNIT-HOLDER RUB JC97-01846B 8.8-39-3 PBA SUB-PAPER SEN...
• Spring Hook Standard : For general use • Tweezers Standard : For general home use, small type. • Cotton Swab Standard : For general home use, for medical service. • Software (Driver) installation CD ROM Service Manual 12-1 Samsung Electronics...
First Copy Out Time Read Only Memory firmware Second Cassette Feeder graphics device interface SMPS Switching Mode Power Supply ground SPGP Samsung Printer Graphic Processor Host Based Printing Samsung Printer Language Hard Disk Drive Spool Simultaneous Peripheral Operation Online high voltage Switch HVPS...
The life of the toner cartridge and the printing speed are measured using the pattern shown below. (The image is 70% of the actual A4 size). 12.3.1 A4 ISO 19752 Standard Pattern This test page is reproduced at 70% of the normal A4 size Service Manual 12-3 Samsung Electronics...
The most of main wireless networking companies are attending and the main companies are Lucent technologies, Cisco, Intel/Symbol, 3Com, Enterasys (Cabletron), Compaq, IBM, Nokia, Dell, Philips, Samsung elec- tronic, Sony, Intersil, and so on. This mark certifies mutual compatibility among product has Wi-Fi (IEEE 802.1) and it is certified as a standard of...
Page 267
GSPN (Global Service Partner Network) North America : service.samsungportal.com Latin America : latin.samsungportal.com CIS : cis.samsungportal.com Europe : europe.samsungportal.com Samsung Electronics Co.,Ltd. February. 2006 China : china.samsungportal.com Printed in Korea. Asia : asia.samsungportal.com VERSION NO. : 1.01 CODE : JC-0157Z...