Related Manuals for Allen-Bradley 1783-EMS08T
Summary of Contents for Allen-Bradley 1783-EMS08T
-
Page 1: Table Of Contents
Installation Instructions Original Instructions Stratix 6000 Ethernet Managed Switches Catalog Numbers 1783-EMS08T, 1783-EMS04T Topic Page Summary of Changes About the Switch Install the Switch DIN Rail Mounting Panel Mounting Wire the Switch Connect the Copper Ethernet Ports Install an Optional SFP Module... -
Page 2: Topic Page
Stratix 6000 Ethernet Managed Switches Summary of Changes This publication contains new and updated information as indicated in the following table. Topic Page ATEX certification and temp code 5, 19 China RoHS table ATTENTION statement about using shielded Ethernet cables ATTENTION: Environment and Enclosure This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in EN/IEC 60664-1), at altitudes... - Page 3 Stratix 6000 Ethernet Managed Switches ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
- Page 4 Stratix 6000 Ethernet Managed Switches North American Hazardous Location Approval The following information applies when Informations sur l’utilisation de cet operating this equipment in hazardous équipement en environnements dangereux. locations. Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne Products marked "CL I, DIV 2, GP A, B, C, D"...
- Page 5 Stratix 6000 Ethernet Managed Switches European Hazardous Location Approval The following applies to products marked II 3 G: • Are Equipment Group II, Equipment Category 3, and comply with the Essential Health and Safety Requirements relating to the design and construction of such equipment given in Annex II to Directive 94/9/EC.
- Page 6 Stratix 6000 Ethernet Managed Switches ATTENTION: Prevent Electrostatic Discharge This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: • Touch a grounded object to discharge potential static. •...
- Page 7 Stratix 6000 Ethernet Managed Switches Name and Content of Hazardous Substances in Product Component Hazardous Substances Name Hexavalent Polybrominated Polybrominated Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) Printed circuit board assemblies Metal components Plastic Components This table is made per guidance of SJ/T 11364.
-
Page 8: About The Switch
Logix control system. The switch integrates into Logix programs and update tags automatically. Use the switch to help continuously monitor your network and implement changes. The figure shows Ethernet port identification for the 1783-EMS08T 8-port and the 1783-EMS04T 4-port switches. Ethernet Port Identification 1783-EMS04T... -
Page 9: Din Rail Mounting
Stratix 6000 Ethernet Managed Switches DIN Rail Mounting Read this section to install and remove a switch that uses DIN rail mounting. Install the Switch To install the switch on DIN rail, proceed as follows. 1. Mount your DIN rail. 2. - Page 10 Stratix 6000 Ethernet Managed Switches Remove the Switch To remove the switch from DIN rail, proceed as follows. 1. Place a screwdriver in the DIN rail latch at the bottom of the switch. 2. Hold the switch and pry downward on the latch until the switch is released from the DIN rail.
-
Page 11: Panel Mounting
Panel Mounting To panel mount a switch, create a mounting template. Refer to the following figure, which shows a 1783-EMS08T switch with a small form-factor pluggable (SFP) module installed. Provide 15 mm (0.6 in.) clearance for DIN rail latch movement during installation and removal. -
Page 12: Wire The Switch
Provide low voltage DC power to the switch by using the screw terminals at the bottom of the switch. Item Description Item Description Side view Ground Bottom view Fiber-optic SFP slot (1783-EMS08T switch only) DC + Rockwell Automation Publication 1783-IN004C-EN-P - April 2016... -
Page 13: Connect The Copper Ethernet Ports
Stratix 6000 Ethernet Managed Switches Follow these steps to wire the switch. 1. Be sure that power to the power supply is turned off. 2. Be sure that you have the proper gauge of wire for your power supply. 3. Strip approximately 0.9 mm (0.35 in.) from each end of the wire. 4. -
Page 14: Install An Optional Sfp Module
You can install a 1G fiber small form-factor pluggable (SFP) module into the fiber-optic Ethernet slot on the bottom to the 1783-EMS08T switch. To install the SFP module, grasp the module on the sides and insert it into the slot until you feel the connector snap into place. -
Page 15: Connect The Fiber-Optic Ethernet Port
The 1783-EMS08T switch supports only 1G fiber SFP modules. Connect the Fiber-optic Ethernet Port To connect the fiber-optic Ethernet port (on the SFP) in the 1783-EMS08T switch after inserting the SFP module, follow these steps. 1. Connect the duplex LC connector end of the fiber-optic cable, in the proper orientation, to the fiber-optic Ethernet port on the SFP module. -
Page 16: Use The Switch
Stratix 6000 Ethernet Managed Switches Use the Switch To start using your switch, follow this procedure. For information about the status indicators on the switch, refer to the Stratix 6000 Ethernet Managed Switch User Manual, publication 1783-UM001. 1. Connect to the LAN card in your computer by using a patch or cross-over cable, and then do the following. - Page 17 Stratix 6000 Ethernet Managed Switches c. From the Ethernet Protocol (TCP/IP) Properties menu, change the IP address to 192.168.1.3 and subnet mask to 255.255.255.0. 2. Connect to the switch via a Web browser by using these steps. a. Open a browser window. b.
-
Page 18: Specifications
Stratix 6000 Ethernet Managed Switches Specifications Stratix 6000 Ethernet Managed Switches Attribute 1783-EMS08T 1783-EMS04T 250 mA @ 24V DC (12…48V DC) 100 mA @ 24V DC (12…48 V DC) Power requirements Class 2/SELV Class 2/SELV Power dissipation 5.8 W 2.6 W Thermal dissipation 24.6 BTU/hr @ 60 °C (140 °F) max... - Page 19 Stratix 6000 Ethernet Managed Switches Stratix 6000 Ethernet Managed Switches (Continued) Attribute 1783-EMS08T 1783-EMS04T Ethernet connections: RJ45 connector according to IEC 60603-7, 2 or 4 pair Category 5e minimum cable according to TIA 568-B.1 or Category 5 cable according to ISO/IEC 24702...
-
Page 20: Additional Resources
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page. Allen-Bradley, Logix5000, Stratix 6000, Rockwell Automation, and Rockwell Software are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400...