For Your Safety Read Before Operating; Operating Instructions - Raypak RAYTHERM 0133-4001 Installation And Operating Instructions Manual

LIGHTING INSTRUCTIONS FOR BOILERS WITH ELECTRONIC IGNITION (IID)
For Models with Manual Gas Valves
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition device which
automatically lights the pilot. Do not try to light the pilot
by hand.
B. BEFORE OPERATING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electric switch; do not use any phone
in your building.
* Immediately call your gas supplier from your neighbor's
phone. Follow the gas supplier's instructions.
1. STOP! Read the safety information above.
2. Set the thermostat on the lowest setting.
3. Turn off all electrical power to the appliance.
4. This appliance is equipped with an ignition device which
automatically lights the pilot. Do not try to light the pilot
by hand.
5. Remove boiler door panel.
6. For Robertshaw gas valve: Turn gas control knob
clockwise to "OFF".
For Honeywell gas valve (all models except 40#):
Turn gas control knob clockwise
Make sure knob rest against stop.
For Honeywell gas valve (Models 40# only):
Push in gas control knob slightly and turn clockwise
to "OFF". Knob cannot be turned to "OFF"
unless knob is pushed in slightly. Do not force.
7. Wait five (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas, STOP!
Follow "B" in the safety information above. If
you do not smell gas, go to the next step.
8. For Robertshaw gas valve: Turn gas control knob
counter-clockwise
ROBERTSHAW
GAS CONTROL
KNOB SHOWN
IN "ON" POSITION
GAS INLET
Fig. # 8080
1. Set the thermostat to the lowest setting.
2. Turn off all the electrical power to the appliance if service
is to be performed.
3. Remove door panel.
4. For Robertshaw gas valve: Turn gas control knob
clockwise to "OFF".
For Honeywell gas valve (all models except 40#):

FOR YOUR SAFETY READ BEFORE OPERATING

OPERATING INSTRUCTIONS

to "OFF".
to "ON".
TO TURN OFF GAS TO APPLIANCE
* If you cannot reach your gas supplier, call the fire de-
partment.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, do not try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
For Honeywell gas valve: Turn gas control knob
counter-clockwise
stops. Push in gas control knob and continue
rotating counter-clockwise
position. Make sure knob rests against stop.
HONEYWELL
GAS CONTROL
KNOB SHOWN
IN "ON" POSITION
GAS INLET
For Honeywell gas valve (Models 40# only):
Turn gas control knob counter-clockwise
GAS CONTROL KNOB
SHOWN IN "ON"
POSITION
GAS INLET
9. Replace boiler door panel.
10. Turn on all electrical power to the appliance.
11. Set thermostat to desired setting.
12. If the appliance will not operate, follow the instructions
"To Turn Off Gas To Appliance" and call your service
technician or gas supplier.
Turn gas control knob clock-wise
Make sure knob rests against stop.
For Honeywell gas valve (Models 40# only):
Push in gas control knob slightly and turn clockwise
to "OFF".
5. Replace heater door panel.
27
from "OFF" until it
to "ON"
Fig. # 8082
to "ON".
Fig. #8219
to "OFF".