Specifications - Makita BFT021F Instructions Manual

ENGLISH
1-1. Battery cartridge
1-2. Button
2-1. Red part
2-2. Button
2-3. Battery cartridge
3-1. Switch trigger
4-1. Reversing switch lever
5-1. Front lamp

SPECIFICATIONS

Model
Hard joint
Fastening
torque
Soft joint
-1
No load speed (min
Dimensions
Net weight
Rated voltage
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is not more
than 70 dB (A).
The noise level under working may exceed 85 dB (A).
Wear ear protection.
The typical weighted root mean square acceleration
value is not more than 2.5 m/s
These values have been obtained according to
EN60745.
Model; BFT020F,BFT021F,BFT040F,BFT042F,
BFT080F,BFT081F,BFT122F,BFT123F
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
Explanation of general view
6-1. LED indicator
7-1. Adjusting ring
7-2. Ring
8-1. Adjusting ring
8-2. Ring
8-3. Scale
8-4. Adjusting grip
8-5. Hole for adjusting grip
BFT020F BFT021F
0.5 - 2 N•m 0.5 - 2 N•m
0.5 - 2 N•m 0.5 - 2 N•m
) 540 320
(with Battery Cartridge BH9020/BH9020A)
(with Battery Cartridge BH9033/BH9033A)
(with Battery Cartridge BH9020/BH9020A)
(with Battery Cartridge BH9033/BH9033A)
2
.
BFT040F BFT080F
1 - 4 N•m 3 - 8 N•m
1 - 3.5 N•m 3 - 6.5 N•m
950 540
200 x 65 x 251mm
200 x 65 x 274 mm
1.3 kg
1.5 kg
D.C.9.6V
ENE033-1
product is in compliance with the following standards of
standardized documents;
EN60745,
Directives, 89/336/EEC, 98/37/EC.
ENF002-1
000087
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
ENG001-2
8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
ADDITIONAL SAFETY RULES
FOR TOOL
1. Be aware that this tool is always in an
operating condition, because it does not have
to be plugged into an electrical outlet.
ENH102-5
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live"
wire will also make exposed metal parts of the tool
"live" and shock the operator.
3
8-6. Yellow line
8-7. Compression spring
10-1. Bit
10-2. Sleeve
12-1. Limit mark
13-1. Brush holder cap
13-2. Screwdriver
BFT122F BFT042F
5 - 12 N•m 1 - 4 N•m
5 - 10 N•m 1 - 3.5 N•m
320 1,200
200 x 71 x 242 mm
(with Battery Cartridge BH1220C)
200 x 71 x251 mm
(with Battery Cartridge BH1233C)
(with Battery Cartridge BH1220C)
(with Battery Cartridge BH1233C)
EN55014 in accordance
Yasuhiko Kanzaki CE2006
Director
BFT081F BFT123F
3 - 8 N•m 5 - 12 N•m
3 - 7.5 N•m 5 - 12 N•m
700 390
1.5 kg
1.7 kg
D.C.12V
with Council
ENB026-1