Important Safety Instructions; Country Of Origin - Bestway BOLT X2 Owner's Manual

Hide thumbs Also See for BOLT X2:

Owner's manual (2 pages)

Owner's manual (2 pages)

Table Of Contents

Table of Contents

Available languages

#65061

Boat

Components:

• Wrench x 1 pc

• Glue x 1 pc

• Pressure gauge x 1 pc

• Repair patch x 1 pc

Footrest Tube x 2 pcs

Footrest Foam x 2 pcs

Safety Rope x 2 pcs

NOTE: All drawings for illustration purpose only. May not reflect actual product. Not to scale.

Footrest Foam

Seat

Safety rope

EN ISO 6185 - 1

0.15 bar

2 psi

HOLDER OF CERTIFICATE: BESTWAY INFLATABLES &

MATERIAL CORP.NO.3065 CAOAN ROAD,SHANGHAI,201812,CHINA

TYPE OF MODEL NUMBER: 65061

COUNTRY OF ORIGIN:

WARNING: To avoid damage to the boat and injury to passengers, please don't

exceed the data given on the builder's plate.

Technical Specifications

Recommended

Item

Inflated Size

working pressure

3.85 m x 93 cm

0.15 bar

65061

(152" x 37")

2 psi

Removable

Hand Pump x 1pc

Fin x 2 pcs

Travel Bag x 1 pc

Seat x 2 pcs

Footrest Tube

Belt

D-ring

TYPE III

= 2

= 0

= 170 kg (374 lbs.)

300m

Sheltered Water

MANUFACTURER:

CHINA

Maximum load capacity

Maximum number of persons

170 kg (374 lbs.)

Follow all the Safety and Operating Instructions. If you don't follow this instructions, it may cause

overturn, explode the boat and causes to drowning.

1. Do not exceed the maximum recommended number of persons. Regardless of the number of

Oar blade x 4

persons on board, the total weight of persons and equipment must never exceed the

Shaft x 2

maximum recommended load. Always use the seats /seating spaces provided.

Coupling x 4

2. When loading the craft, never exceeds the maximum recommended load: Always load the

Oar

craft carefully and distribute loads appropriately to maintain design trim (approximately level).

Avoid placing heavy weights high up.

NOTE: The maximum recommended load includes the weight of all persons onboard, all

provisions and personal effects, any equipment not included in the light craft mass, cargo (if

any) and all consumable liquids(water, fuel, etc.).

3. When using the boat, life saving devices such as life jackets and buoys should be

pre-inspected and used at all times.

4. Before every use, carefully inspect all boat components including air-chambers, grab ropes,

oars, and air valves, to ensure everything is in good condition and tightly secured. Please

stop to repair if you find any damage.

5. Buckets, water scoops and air pumps should always be available in case of air leakage or if

the boat takes on water.

6. When the boat is in motion, all passengers must remain seated at all times to avoid going

overboard. Keep the boat balanced. Uneven distribution of persons or load in the boat may

cause overturn the boat and drowning.

7. Use the craft in sheltered water, up to 300m (984 feet). Be careful with natural factors such as

wind, tide waters and tidal waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS.

Always wear a lifejacket!

8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate

the other air chamber to prevent the boat from sinking.

9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement,

shells, glass, etc. may punctured the boat. To avoid damage do not drag the boat on rough

surfaces.

10. The boat is intended for beach use, short-time and short-distance cruising.

11. Be aware of the potential harmful effects of liquids such as battery acid, oil, petrol. The liquids

may damage your boat.

12. Inflate according the numbered air chamber and rated pressure on the boat, or it will cause

over inflation and boat explosion. Exceeding the data given on the capacity plate may cause

the craft to damage, overturn and lead to drowning.

13. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.

14. Know how to operate a boat. Check in your local area for information and/or training as

needed. Inform yourself about local regulations and dangers related to boating and/or other

water activities.

SAVE THESE INSTRUCTIONS

Installation

1. Spread out the kayak on level ground.

2. Assemble the removable fin to the bottom of the kayak (Fig.1). Make sure the curvature of the

fin is pointed towards the back end of the kayak.

NOTE: Assemble the fin before inflation and also disassemble it after deflation.

NOTE: To avoid damage to the removable fin, do not enter shallow water.

Removable fin

Fig. 1

3. Inflate the kayak by unscrewing the cap of the air valve (Fig.2 pos.1). Ensure that the

inner spring valve is not depressed. If it is depressed (Fig. 2 pos. 2), press the spring

valve and turn counter clockwise so the inner spring valve is in the correct position (Fig.2

pos. 3). Attached the pressure gauge onto the hose and the hose to the inflate position on

the high-pressure hand pump. Inflate the kayak to 0.15bar (2psi). After inflation, screw the

cap of air valve (Fig.2 pos. 4)

NOTE: If over-inflation occurs, press the spring valve to release air to an acceptable level

and securely fasten the air valve.

NOTE: If the kayak is not in use and exposed under the sun, it may cause overexpansion

and damage the kayak. Check the pressure and deflate slightly until the correct pressure

is obtained.

NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge

is just for reference, should not be used as a precision instrument.

Fig. 2

2 adults

Warning