Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Chauvet DJ 4BAR USB
Summary of Contents for Chauvet DJ 4BAR USB
- Page 1 User Manual...
-
Page 2: Table Of Contents
Master/Slave Expansion Mode ..................... 16 Expansion Mode (Wired) ........................16 Expansion Mode (D-Fi USB) ........................ 16 5. Maintenance .........................17 Product Maintenance ........................17 6. Technical Specifications ....................18 Returns ..........................19 Contact Us ..........................20 Page 2 of 20 4BAR USB User Manual Rev. 2... -
Page 3: Before You Begin
Chauvet & Sons Inc. (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies. 4BAR USB User Manual Rev. 2 Page 3 of 20... -
Page 4: Product At A Glance
Keep this User Manual for future use. If you sell the product, be sure that they also receive this document. Page 4 of 20 4BAR USB User Manual Rev. 2... -
Page 5: Introduction
2. I NTRODUCTION Product Overview 4BAR USB - Back Panel View D-Fi USB Menu Microphone Port Buttons Display Fuse Holder In/Out Power In Footswitch 9-Volt Battery Cover Switch Power Switch WARNING! DO NOT plug anything other than a D-Fi USB into the USB port. Doing so may cause damage to the product. -
Page 6: Product Dimensions
Product Dimensions 47.4 in 1205 mm 11 in 284.5 mm Front View 2 in 50 mm Side View Page 6 of 20 4BAR USB User Manual Rev. 2... -
Page 7: Setup
3. S ETUP The 4BAR USB has an auto-ranging power supply and it can work with an input voltage AC Power range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. -
Page 8: Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The 4BAR USB may be mounted in any position; however, make sure adequate ventilation is provided around the product. · Rigging Before deciding on a location for the product, always make sure there is easy access to the product for maintenance and programming purposes. -
Page 9: Operation
Address The 4BAR USB uses up to 15 DMX channels in a 15-CH DMX mode, which defines the highest configurable address to 498. If you are not familiar with the DMX protocol, download the DMX Primer from www.chauvetlighting.com. -
Page 10: D-Fi Usb Connectivity
The 4BAR USB is able to become a D-Fi wireless receiver/transmitter with the use of the D- D-Fi USB Fi USB from Chauvet DJ. Simply set the product's DMX Personality and DMX Address, set Connectivity the DIP switch D-Fi receiving/transmitting channel, then plug it into the D-Fi USB port. -
Page 11: Dmx Channel Assignments And Values
(Pod 3) Blue 000ó255 0–100% 000ó255 0–100% RGB Color Mixing Green 000ó255 0–100% (Pod 4) Blue 000ó255 0–100% Channel Function Value Percent/Setting 3-CH 000ó255 0–100% Green 000ó255 0–100% Blue 000ó255 0–100% 4BAR USB User Manual Rev. 2 Page 11 of 20... -
Page 12: Configuration (Standalone)
DMX controller. Products in standalone mode may transmit DMX signals that could interfere with the DMX signals from the controller. To run the 4BAR USB in Preset Color mode, follow the instructions below: Preset Colors Press <MENU> repeatedly until C-- shows on the display. -
Page 13: Wireless Footswitch
The 4BAR USB footswitch will work properly in any mode, with a maximum unobstructed distance of 50 ft (15.24 m). You must turn on the rF on the 4BAR USB, set the rF channel, and navigate to Auto mode before using the footswitch. -
Page 14: Irc-6 Infrared Remote Control
The 4BAR USB is compatible with the IRC-6 infrared remote control from Chauvet. To IRC-6 Infrared activate IR mode, follow the instructions below: Remote Press <MENU> repeatedly until Ser shows on the display. Control Press <ENTER> to accept. Press <UP> or <DOWN> to select ON or OFF. -
Page 15: Master/Slave Mode (Wired)
Do not connect more than 31 slaves to the master. Master/Slave The D-Fi USB allows a single 4BAR USB product (the master) to control the actions of one or more 4BAR USB products (the slaves) without the need of a DMX controller or DMX Mode cables. -
Page 16: Master/Slave Expansion Mode
Expansion COREpar USB, SlimPAR USB, or Freedom Par, without the need of a DMX controller, with the use of the optional D-Fi USB (not included). The 4BAR USB will be set to operate Mode in either standalone mode or with the footswitch, while the slave products will be set to operate in slave mode. -
Page 17: Maintenance
Softly drag any dirt or grime to the outside of the transparent surface. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. 4BAR USB User Manual Rev. 2 Page 17 of 20... -
Page 18: Technical Specifications
Maximum External Temp. Cooling System 104 °F (40 °C) Convection I/O Connectors Channel Range 3-pin XLR 3 or 15 Ordering Product Name Item Code UPC Number 4BAR USB 03031129 78146221477 Page 18 of 20 4BAR USB User Manual Rev. 2... -
Page 19: Returns
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. Chauvet reserves the right to use its own discretion to repair or replace returned product(s). 4BAR USB User Manual Rev. 2 Page 19 of 20... -
Page 20: Contact Us
+52 (728) 690-2010 Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux contact your dealer. Follow their instructions to request support or to return a product. Visit our website for contact details. Page 20 of 20 4BAR USB User Manual Rev. 2...