Parts Identification - StreetStrider 7i Owner's Manual

2| PARTS IDENTIFICATION

Table 2.1 StreetStrider Parts List with Hardware Specifications, Quantity, and Maintenance State.
Parts are numbered in previous figures.
# DESCRIPTION HARDWARE
1
Main Frame Bone
2 Head Tube Bottle cage bosses
3 Crossbar
4
Front Beam
5 Fold Joint Quick Release clamp
stem nylon lock nut
6
Stride Pole Upper
7 Stride Pole Lower
8
Strider Ski Quick release clamp
Composite bushings
Roller bearings
9 Foot Platform 4 mm hex screw,
10
Rear Fender Frame 4 mm hex screw,
11 Fender Stay
12
Chain Stay
13 Hand Grip
14 Twist Grip Shifter 3 mm hex screw
15 Brake Lever 5 mm hex screw
Parking pin
Cable housing adjuster
Cable doubler
16
Joint #1, Cross Bar-Pole 4 mm hex screw
Pivot Clamp Assembly
3 mm hex set screw
4 mm hex pan head
Roller bearings
4 mm flat head screw
17
Joint #2, Pole-Ski Pivot 8 mm hex screw,
washer,
17 mm nut
18 Joint #3, Ski-Pedal Pivot 6 mm hex spindle
19 Front Beam Pivot 8 mm hex screw
3 mm hex set screw
Tapered roller bearing
20
Front Wheel and Tire
21 Front wheel hub 19 mm hex axle nut
6
SPECIFICATIONS QTY
1
M5 x P0.8 threads for 2 cages 4
1
1
M6 x P1.0 x L20 x H10 x W10 1
Left and right side 2
2
Left and right side, QR on left ski 2
OD12 x ID10 x L15 x 17 mm flange, at Joint #2 4
OD 26 x ID 18 x L 20, at Joint #3 4
M5 x P0.8 x L12 x H12 x W4, flat head 12
M5 x P0.8 threaded hole for luggage rack 1
2
2
Left and right side, rubber 2
M4 x P0.7 x L16 x W3, clamp 1
M5 x P0.8 x L20 x H10 x W5, clamp 2
OD 10, spring loaded 2
M10 x P2.0 barrel adjuster with lock ring 2
Front brake, with adjuster and lock ring 1
M5 x P0.8 x L30 x H8 x W4, clamp cap 8
M6 x P1.0 x L5, with cup end, cross bar 8
M6 x P1.0 x L10 lock screw 2
OD26 x ID18 x L20, in cross bar 4
M6 x P1.0 x L20, inner shaft end 2
M10 x P1.5 x L75 x H15 x W8 2
OD16 x ID10 x T1 2
M10 x P1.5 x L10 x W17, nylon lock 2
OD18 X L60 x W6, thd 9/16" right and left, C clip 2
M10 x P1.5 x L20 x W8, front cap 1
M6 x P1.0 x L5 x W3, rear end 1
OD 47 x ID 20 X T15 2
Tire 16" x 1 3/8", ISO 37 x 349 2
M12 x P1.75 x L10 x W19, nylon lock 2
# DESCRIPTION
22 Steering Linkage
STATE
23 Bottle Cage
24
Crank Arm Set with
Bottom Bracket
Tighten to secure
cages
25 Chain Ring With Guard
26
Chain
27 Rear Wheel and Tire
28
Internal Gear Hub
Snug to secure
29 Front Disc Brake
Snug to secure
Grease
Grease
30
Front Disc Rotor
Tighten
31 King Pin Bolt In Front
beam clevis
32 Steering knuckle w/
Lean Stop
Tighten
Tighten
33
Bell Crank for 3 Speed
Hub
Adjust-lock
Adjust-lock
34 Rear Disc Brake
Tighten evenly to
secure pole
Tighten
Tighten
Grease
Tighten
35 Rear Disc Rotor
Snug but allow
36
Rear Drop Out
joint movement
Tighten
37 Shifter Cassette for 7 Sp
Tighten
Tighten
Grease
80-85 psi
Tighten
HARDWARE SPECIFICATIONS
Inboard and outboard M8 x P1.25 x L20 x W14 flats on stud
rod ends M8 x P1.25 x L10 x W13 nylon lock nut
Threaded linkage rod M8 x P1.25 x L20 rod, right and left thread ends
M8 x P1.25 x L5 x W14, right and left jam nuts
4 mm hex in boss M5 x P0.8 x L12 x H10 x W4, socket
8 mm hex screw M8 x P1.0 x L15 x H12 x W8, 18 mm flange
Square taper 68 x 122 mm
52 T
1/2" x 1/8" x 93 links
Tire 20" x 1 3/8", ISO 37 x 451
15 mm axle nuts 3 or 7 speed, 3/8" x 26 tpi x W15 axle nuts
5 mm hex mount screw M6 x P1.0 x L15 x H10 x W5, through knuckle
5 mm hex caliper screw M6 x P1.0 x L15 x H10 x W5, through bracket
5 mm hex outer pad W5 outer pad adjuster with 2 mm lock set screw
3 mm hex inner pad W3 inner pad adjuster, through center screw hole
Cable housing adjuster M6 x P1.0 x L15 knurled for fingers with lock ring
4 mm hex cable clamp M5 x P0.8 x L12 x H10 x W4, socket and nut
4 mm hex screw M5 x P0.8 x L10 x H10 x W4, pan head
8 mm hex bolt M10 x P1.5 x L75 x H15 x W8, socket
washer OD16 x ID10 x T1
17 mm nut M10 x P1.5 x L10 x W17, nylon lock
5 mm hex screw M6 x P1.0 x L15 x H10 x W5, socket screw
W10 nylon lock nut
Lean stop disc OD24 x T4 with 6 mm offset hole
Composite bushing OD12 x ID10 x L15 x 17 mm flange
2.5 mm hex screw M5 x P0.8 x L6 x W2.5 set screw
Gear alignment window
Shift cable barrel adjuster
5 mm hex mount screw M6 x P1.0 x L15 x H10 x W5, through drop out
5 mm hex caliper screw M6 x P1.0 x L15 x H10 x W5, through bracket
5 mm hex outer pad W5 outer pad adjuster with 2 mm lock set screw
3 mm hex inner pad W3 inner pad adjuster, through center screw hole
Cable housing adjuster M6 x P1.0 x L15 knurled for fingers with lock ring
4 mm hex cable clamp M5 x P0.8 x L12 x H10 x W4, socket and nut
4 mm hex screw M5 x P0.8 x L10 x H10 x W4, pan head
Dropout slot for rear hub axle
Holes for rear brake mounting bracket
M5 x P0.8 hole for rear luggage rack screw
Cassette pulley and lock ring on 7 sp hub
M=OD of threads, mm L=length
Specification
Key
P=pitch, threads/mm H=OD of head
QTY STATE
Lubricate balls
4 Tighten
2 Tighten
4 Tighten
2 Tighten
2 Tighten
1 Tighten
1
1 Lubricate
1 80-85 psi
2 Tighten
4 Tighten
4 Adjust-tighten
2 Adjust-tighten
2 Adjust
2 Adjust-lock
2 Adjust-tighten
12 Tighten
2
Snug but allow
2
knuckle swivel
2
2 Adjust-tighten
4 Grease
1 Snug to secure
1 Adjust
2 Tighten
2 Adjust-tighten
1 Adjust-tighten
1 Adjust
1 Adjust-lock
1 Adjust-tighten
6 Tighten
2
4
2
1 Install-lock
W=wrench fit, mm
T=washer thickness, mm
7