Related Manuals for StreetStrider Summit 8r
Summary of Contents for StreetStrider Summit 8r
- Page 1 Summit 8r / Sprinter 3r OWNER’S MANUAL 7042 North West Street, Suite 110, Fresno, CA 93711 1.800.348.0998 www.StreetStrider.com...
-
Page 2: Table Of Contents
RECORDS Please record your StreetStrider model name (Summit 8r or Sprinter 3r), serial number (found on the frame around the bottom bracket; see photo) and other information below. Please retain your sales receipt as proof of purchase and keep with this information. -
Page 3: About This Manual
1. About This Manual . This StreetStrider Summit 8r/Sprinter 3r Owner’s Manual contains important assembly, maintenance, safety and performance information. It was written to help you get the most performance, comfort, enjoyment and safety out of your new StreetStrider. -
Page 4: Parts Identification
2. Parts Identification The parts of the StreetStrider Summit 8r/Sprinter 3r are listed and labeled in the following table and figures. Table 2-1. StreetStrider Parts List with Hardware Specifications, Quantity, and Maintenance State. Parts are numbered in subsequent figures. DESCRIPTION... - Page 5 Mounting screw 5 mm hex Snug w/ air gap Cable adjuster 10 mm nut Tighten Specification M=OD of threads, mm L=length W=wrench fit, mm P=pitch, threads/mm H=OD of head T=washer thickness, mm StreetStrider Summit 8r / Sprinter 3r Owner’s Manual...
- Page 6 Figure 2-1. StreetStrider Summit 8r / Sprinter 3r Parts. Refer to Table 2-1 for part numbers and descriptions. StreetStrider Summit 8r / Sprinter 3r Owner’s Manual...
- Page 7 Figure 2-2. StreetStrider Summit 8r / Sprinter 3r Parts. Refer to Table 2-1 for part numbers and descriptions. StreetStrider Summit 8r / Sprinter 3r Owner’s Manual...
-
Page 8: Unpacking & Assembly
3. Unpacking and Assembly This chapter refers to the assembly of both the StreetStrider Summit 8r and Sprinter 3r models, unless instructions specify one model or the other. To assemble your StreetStrider Summit 8r/Sprinter 3r, first view the StreetStrider Workshop videos provided to you on the StreetStrider DVD, then follow the steps and photos in this chapter. - Page 9 At the factory, the poles are set at the highest position and rotated inward for packing. Use a 5 mm hex wrench to loosen the 2 screws in each clamp at the base of each strider StreetStrider Summit 8r / Sprinter 3r Owner’s Manual...
- Page 10 (Fig. 3-8c). Once the brake levers are positioned, rotate the twist shifter so that the gear number is facing the rider, then tighten. Installing the Rear Wheel – Sprinter 3r (see next section for Summit 8r) Remove ties and packing material from the rear triangle (Fig. 3-9a) and from the chain (Fig.
- Page 11 Finally, close the quick release rear brake and check that the brake shoes contact the rear rim on the side face. Adjust if necessary. Installing the Rear Wheel – Summit 8r (see previous section for Sprinter 3r) ...
- Page 12 80 psi. Next, locate the spherical rod ends on each end of the steering linkage rods (Fig. 3-19a). The inboard rod end has left hand threads and the outboard rod end has right hand threads. Each rod end is screwed into the aluminum rod and StreetStrider Summit 8r / Sprinter 3r Owner’s Manual...
- Page 13 Figure 3-21. Adjusting the rear hub shifter - Summit 8r (see Fig. 3-22 for Sprinter 3r) With the twist grip shifter of the Summit 8r in 4th gear (Fig. 3-21a), the two yellow setting lines in the gear alignment window should be together (Fig.
- Page 14 Figure 3-23. Installing the rear rack – Summit 8r To install the rear rack that comes with the Summit 8r, you will need the 4 mm hex wrenches and 3 of the remaining stainless steel cap screws and washers (Fig. 3-23a) from the packet in the small cardboard box. Position the rack over the rear frame with three securing points (Fig.
-
Page 15: Simple Steps To Learn To Stride
The StreetStrider Summit 8r has 8 gears and the Sprinter 3r has 3 gears. Gears 1, 2 and 3 of the Sprinter 3r have similar ratios to gears 4, 6 and 8 of the Summit 8r. When you stride on flat ground, shift to one of the higher gears to get the smoothest arm and leg motion. -
Page 16: Safety Equipment
StreetStrider, like any object, is more difficult for motorists and pedestrians to see at dusk, night, or any other time of poor visibility. Make sure you comply with all local laws about night riding and take the following additional precautions: StreetStrider Summit 8r / Sprinter 3r Owner’s Manual... -
Page 17: Mechanical Safety Check
So you need to know and practice the rules of safe and responsible StreetStriding. Now buckle on your helmet and enjoy your StreetStrider. StreetStrider Summit 8r / Sprinter 3r Owner’s Manual... -
Page 18: Limited Warranty
StreetStrider and any other losses if the StreetStrider is used in any competitive event, including racing, ramp jumping, stunt riding or similar activities or training for such competitive activities or events. This StreetStrider is not StreetStrider Summit 8r / Sprinter 3r Owner’s Manual... -
Page 19: Return Policy
You don’t need to own a retail store - the only product you have to buy is a StreetStrider for yourself. Just visit our website www.streetstrider.com, click on Sales Affiliates, fill out and submit the form provided, and we will contact you about becoming a StreetStrider Sales Affiliate. Start earning commissions today! StreetStrider Summit 8r / Sprinter 3r Owner’s Manual... - Page 20 7042 North West Street, Suite 110, Fresno, CA 93711 1.800.348.0998 www.StreetStrider.com © FALL 2011...