Table of Contents
Advertisement
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
Feed the thermostat capillary out of the oven. Disconnect
wiring from thermostat. Remove 2 screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped
to the oven back with the phial centrally positioned
between the clips.
Check operation of thermostat.
8. To Change Grill Controller
Lift up the ceramic hob top (see 2). Remove control
panel (see 4). Disconnect wiring from controller. Remove
2 screws holding controller to mounting panel. Fit new
controller and reassemble in reverse order. Check for correct
operation.
9. To Remove Grill Door
Remove the left hand side panel (see 1). Remove the control
panel (see 4). Remove the centre cover strip (5 screws, 2 top,
2 bottom, 1 in middle). Remove the two countersunk screws
(1 each side) securing the grill hinge arms to the front of the
grill chamber.
NOTE: The arms are spring tensioned. Carefully remove the
grill door. Retain the gaskets.
Reassemble in reverse order ensuring that the gasket is
fitted between the hinge arm and the front of the grill
chamber.
10. To Remove Main Oven Door
Open oven door and remove Handyrack (where fitted)
by springing one side out of the bracket on the door and
sliding the other side free. Support the door and remove
the two screws securing the upper hinge and packing to
the cooker front. Remove the door from the lower hinge by
lifting slightly and moving outwards.
Reassemble in reverse order.
11. To Change Main Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel
fixing screws from the door sides (two each side).
Carefully lift off the outer door panel.
Remove door handle from panel by unscrewing 2 retaining
nuts. Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.
12. To Change Main Oven Door Latch
Remove outer door panel (see 15). Remove screws 'B'
holding latch assembly to inner door panel. Fit new catch
and reassemble in reverse order.
Check correct door operation.
13. To Change Oven Door Seal
Open oven door. The seal is held in place by small hooks on
the rear face. At the corner pull seal diagonally away from
the door centre until that hook is released. Proceed to the
next hook and release it in a similar way, and so on. Use
force if the hooks are stiff, as the old seal will be discarded.
When fitting new seal, position the seal join at the bottom.
Hook the new seal in one of the corner holes of the door,
and proceed round the door snapping in each hook in turn.
14. To Adjust the Main Oven Door Catch Keep
15. To Change Tall Oven Door Outer Panel
Remove oven door see 12. Lay door face down on a
suitable surface and remove 2 screws from bottom edge
of door and 2 screws from inside face of door.
Remove outer door panel. Remove door handle by
unscrewing 2 screws. Remove 2 cross-headed screws
holding door handle fixing bracket to door panel. Fit
door handle bracket and door handle to new panel.
Fit panel to door. Reassemble in reverse order.
16. To Change Tall Oven Door Magnetic Latch
Remove the control panel (see 1).
Remove the plinth (3 screws) and the central vertical
cover (5 screws). Prize the retaining clip off the magnet
unit. Fit new unit and retaining clip.
Reassemble in reverse order.
30
Open oven door, slacken off
locknut at base of keep, and
screw in or out as required until
required fit is obtained.
Retighten locking nut.
Advertisement
Table of Contents
