Wiring Of Connection Cable; For Safe Use - Mitsubishi Electric GT2104-PMBD Manual

1. GOT series User's Manual Specifications
1.1 General Specifications
Item
*1 0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)
Operating ambient temperature
Storage ambient temperature -20 to 60C
Operating ambient humidity
10% RH to 90% RH, non-condensing
Storage ambient humidity
10% RH to 90% RH, non-condensing
Compliant with
Vibration resistance JIS B3502 and
IEC61131-2
Shock resistant
Compliant with JIS B3502 and IEC61131-2 147m/s
Operating atmosphere No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage)
*3
Operating altitude 2000 m or less
Installation location Inside control panel
*4  or less
Overvoltage category
Pollution degree *5 2 or less
Cooling method Self-cooling
Grounding with a ground resistance of 100 Ω or less by using a ground cable that has a cross-sectional area of 0.14 to 1.5
2
Grounding mm (solid wire), 0.14 to 1.0 mm
If impossible, connect the ground cable to the control panel.
*1 The operating ambient temperature indicates the temperature inside the enclosure of the control panel to which the GOT is installed.
*2 If the ambient temperature exceeds 40°C, the absolute humidity must not exceed 90%RH at 40°C.
*3 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0 m. Doing so may cause a malfunction. When an air purge is made inside
the control panel by adding pressure, there may be a clearance between the surface sheet and the screen, making you difficult to use the touch panel, or the sheet may
come off.
*4 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises. Category II applies to equipment for which electrical power is supplied from fixed facilities. The withstand surge voltage for the equipment
with the rated voltage up to 300 V is 2500 V.
*5 This indicates the occurrence rate of conductive material in an environment where a device is used. Pollution degree 2 indicates an environment where only non-
conductive pollution occurs normally and a temporary conductivity caused by condensation shall be expected depending on the conditions.
*6 DC5V type is not required ground.
1.2 Performance Specifications
Item
GT2104-PMBD
Display device TFT monochrome display
Screen size 4.5"
Resolution 384 × 128 dots
Display size 109.4(4.31) (W) × 36.5(1.44) (H) mm(inch)
Displayed number 16-dot standard font: 24 characters × 8 lines (two-byte characters)
D i s pl a y
of characters 12-dot standard font: 32 characters × 10 lines (two-byte characters)
section
*1*2
Display color Monochrome (black and white) 32 scales
B r i g h t n e s s
32 levels
Adjustment
Backlight 5 colors LED (white, green, pink, orange, red) (Not replaceable)
*3
Approx. 50000 h (operating ambient temperature: 25°C, display intensity: 50%)
Backlight life
Type Analog resistive film
Key size Minimum 2 × 2 dots (per a key)
To u c h
*4
panel *5
Simultaneous press Simultaneous press prohibited
(only 1 point can be pressed)
Life 1 million times or more (Operating force: 0.98 N or less)
User memory
Memory for storage (ROM): 6 MB
U s e r
capacity
memory
L i f e ( n u m b e r o f
capacity
100000 times
write times)
Battery GT11-50BAT lithium battery
Battery
Life Life Approx. 5 years (operating ambient temperature: 25°C)
1 channel Transmission speed: 115200/
57600/38400/19200/9600/4800 bps
RS-232 (rear face) -
Connector shape: MINI-DIN6-pin
(female)
RS-232 (side face) -
1 channel Transmission speed: 115200/ 1 channel Transmission speed: 115200/
B u i l t - i n
57600/38400/19200/9600/4800 bps 57600/38400/19200/9600/4800 bps
interface
Connector shape: terminal block 5-pin Connector shape: terminal block 9-pin
RS-422/485 *6
Terminating resistor : OPEN/110 Ω/ Terminating resistor
330 Ω 330 Ω
(Switched with the terminating resistor (Switched with the terminating resistor
setting switch) setting switch)
RS-422 -
Specifications
*2
*2
Frequency Acceleration Half amplitude
5 to 8.4 Hz - 3.5 mm
Under intermittent
vibration
2
8.4 to 150 Hz 9.8m/s
5 to 8.4 Hz - 1.75 mm
Under continuous
vibration
8.4 to 150 Hz 2
4.9m/s
2
(15G) Three times in each X, Y, or Z direction
2 2
(stranded wire), or 0.25 to 0.5 mm (rod terminal with an insulation sleeve).
*6
Specifications
GT2104-PMBDS GT2104-PMBDS2
1 channel Transmission speed: 115200/
57600/38400/19200/9600/4800 bps
Connector shape: MINI-DIN6-pin
(female)
1 channel Transmission speed: 115200/
- 57600/38400/19200/9600/4800 bps
Connector shape: terminal block 9-pin
*6 -
: OPEN/110 Ω/
1 channel Transmission speed: 115200/
- - 57600/38400/19200/9600/4800 bps
Connector shape: terminal block 9-pin
Item
Ethernet
B u i l t - i n
interface
USB (Device)
SD card
Buzzer output
Sweep Count
Productive structure
10 times in each X,
Y, or Z direction
-
External dimensions
- Panel cut dimensions
-
Weight (excluding a fitting)
Compatible software package
*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible to completely avoid this symptom, as
the liquid crystal display comprises of a great number of display elements. In addition, color tone difference, unevenness of brightness, or flickers may occur due to
individual differences of liquid crystal display panels. Please note that these symptoms occur due to GOT's characteristic and are not caused by product defect.
*2 Flicker may occur due to vibration, shock, or display color.
*3 Settings the screen saving backlight to OFF prevents the display screen from burn-in and enables the backlight to lengthen its life.
*4 When using a stylus pen, it will be 100,000 times. (The specifications must be satisfied the following condition.)
- Material: Polyacetal resin - Tip radius: 0.8 mm or more
*5 If you touch two or more points on the touch panel simultaneously and a switch is placed between the two points, the switch may be activated. Do not touch two or more
points on the touch panel simultaneously.
*6 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.
*7 Note that this does not guarantee all users' operation environment. In addition, the GOT may not be usable in the environment where oil or chemicals are splashed over
for a long time or where oil mist is filled.
1.3 Power Supply Specifications
Item
Input power supply voltage
Under the maximum load
P o w e r
consumption
At backlight off
Inrush current
Permissible instantaneous power failure
time
Noise immunity
Dielectric withstand voltage
GT2104-PMBLS
Insulation resistance
Electrical wire size
Wire type
Temperature rating of a wire
Ferrules with plastic sleeve
Crimper type
Tightening torque (terminal screws)

2. Wiring of connection cable

The diagram below shows cable assignment for GOT port.
Cables for GT2104-PMBD: GT21-CR4-8P5, GT21-CR4-25P5
Cables for GT2104-PMBDS: GT10-CR4-8P, GT10-CR4-25P
Cables for GT2104-PMBDS2: GT10-C30R2-6P
Cables for GT2104-PMBLS: GT10-CR4-8P
GOT
PLC connection cable
GT21-C□□□R4-8P5 GT21-C□□□R4-25P5
GT10-C□□□R4-8P GT10-C□□□R4-25P
GOT
Untied GOT
(terminal
wire (terminal
-
block)
color block)
24V
SDA Brown
SDB Red
RDA Orange
-
RDB Yellow
SG Green
*1 Black *1
RSA
RSB *1 White *1
*1
CSA -
+
CSB *1
-
*1 The cable for GT2104-PMBD does not have the connection to a signal name
(RSA, RSB, CSA, CSB).
User-made cable is necessary, depending on the PLC.
For the detail, refer to GOT2000 Series Connection Manual.
Cable jacket to remove
Tightening torque
Recommended Tool (Screwdriver)
Specifications
GT2104-PMBD GT2104-PMBDS
1 c h a n n e l D a t a t r a n s f e r
method:10BASE-T/100BASE-TX -
Connector shape: RJ-45 (modular jack)
1 ch
Maximum transfer rate: Full-Speed 12 Mbps Connector shape: USB Mini-B
1 channel SDHC card supported (max. 32 GB)
Single tone (tone length adjustable)
*7
Outside the enclosure: IP67F Inside the enclosure: IP2X
145(5.7) (W) × 76(3.0) (H) ×
145(5.7) (W) × 76(3.0) (H) × 29.5(1.17) (D) mm
32.5(1.28) (D) mm
137(5.4) (W) × 66(2.6) (H) mm
0.3kg
GT Works3 Version1.131M or later
Specifications
GT2104-PMBD GT2104-PMBDS
DC24 V (+10%, -15%)
2.9 W or less 2.2 W or less
2.2 W 1.5 W
30 A or less (1ms, 25°C, at the maximum load)
Within 5ms
Noise voltage: 1000 Vp-p, Noise width: 1 μs (by noise simulator of 30 to 100 Hz noise frequency)
500 VAC for 1 minute
(between the GOT's power supply terminals and the GOT's grounding terminal)
10 MΩ or larger by insulation resistance tester
(between the GOT's power supply terminals and the GOT's grounding terminal)
2
No. of wire per terminal: 1 Solid wire 0.14 to 1.5 mm AWG26 to AWG16, Stranded wire 0.14 to 1.0 mm
Ferrules with plastic sleeve 0.25 to 0.5 mm
2
No. of wire per terminal: 2 Solid wire 0.14 to 0.5 mm AWG26 to AWG20, Stranded wire 0.14 to 0.2 mm
Use copper or copper-clad aluminum conductors.
More than 70°C
AI 0.25-6BU (AWG24), AI 0.34-6TQ (AWG22), AI 0.5-6WH (AWG20) (Phoenix Contact Inc.)
CRIMPFOXZA3 (Phoenix Contact Inc.)
0.22 to 0.25 N·m
This manual confers no industrial property rights or any rights of any other
kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation
cannot be held responsible for any problems involving industrial property rights
which may occur as a result of using the contents noted in this manual.
Warranty
Exclusion of loss in opportunity and secondary loss from warranty liability
PLC
Regardless of the gratis warranty term, Mitsubishi shall not be liable for
compensation to:
(1) Damages caused by any cause found not to be the responsibility of
Mitsubishi.
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
products.
(3) Special damages and secondary damages whether foreseeable or not,
compensation for accidents, and compensation for damages to products
GT10-C30R2-6P
other than Mitsubishi products.
Untied
Untied GOT
(4) Replacement by the user, maintenance of on-site equipment, start-up test run
wire (terminal wire
and other tasks.
color block) color
24V 24V
SDA Brown SD Brown
SDB Red
RD Red
RDA Orange ER Blue
RDB Yellow DR Yellow  This product has been manufactured as a general-purpose part for general
SG Green SG Green
industries, and has not been designed or manufactured to be incorporated in
*1
RSA Blue RS Purple
a device or system used in purposes related to human life.
RSB *1 Purple CS
*1 *1  Before using the product for special purposes such as nuclear power, electric
CSA Black NC
CSB *1 White *1
NC power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
 This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
7 mm (0.27")
0.22 to 0.25 N·m
SZS 0.4 × 2.5 (Phoenix Contact Inc.)
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
GT2104-PMBDS2 GT2104-PMBLS
- -
-
0.28kg
GT Works3 Version1.137T or later
GT2104-PMBDS2 GT2104-PMBLS
DC5V (±5%)
1.1W or less
0.7W
-
-
-
-
2
AWG26 to AWG18,
2
AWG24 to AWG20
2
AWG26 to AWG24

For safe use