Download  Print this page

Mitsubishi Electric GT2103-PMBD Manual Page 2

Got 2000 graphic operation terminal, gt21 general description.
Hide thumbs
   

Advertisement

1. GOT series User's Manual Specifications
1.1 General Specifications
Item
*1
Operating ambient temperature
0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)
Storage ambient temperature
-20 to 60C
Operating ambient humidity
10% RH to 90% RH, non-condensing
Storage ambient humidity
10% RH to 90% RH, non-condensing
Compliant with
Vibration resistance
JIS B3502
and IEC61131-2
Shock resistant
Compliant with JIS B3502 and IEC61131-2 147m/s
Operating atmosphere
No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage)
*3
2000 m or less
Operating altitude
Installation location
Inside control panel
 or less
*4
Overvoltage category
Pollution degree
*5
2 or less
Cooling method
Self-cooling
Grounding with a ground resistance of 100 Ω or less by using a ground cable that has a cross-sectional area of 0.14 to 1.5 mm
Grounding
(solid wire), 0.14 to 1.0 mm
If impossible, connect the ground cable to the control panel.
*1 The operating ambient temperature indicates the temperature inside the enclosure of the control panel to which the GOT is installed.
*2 If the ambient temperature exceeds 40°C, the absolute humidity must not exceed 90% at 40°C.
*3 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0 m. Doing so may cause a malfunction. When an air purge is made inside
the control panel by adding pressure, there may be a clearance between the surface sheet and the screen, making you difficult to use the touch panel, or the sheet may
come off.
*4 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the
machinery within the premises. Category II applies to equipment for which electrical power is supplied from fixed facilities. The withstand surge voltage for the equipment
with the rated voltage up to 300 V is 2500 V.
*5 This indicates the occurrence rate of conductive material in an environment where a device is used. Pollution degree 2 indicates an environment where only non-
conductive pollution occurs normally and a temporary conductivity caused by condensation shall be expected depending on the conditions.
*6 Except 5 V power supply type.
1.2 Performance Specifications
Item
GT2103-PMBD
Display device
TFT monochrome display
Screen size
3.8"
Resolution
320 × 128 dots
Display size
89.0(3.51) (W) × 35.6(1.41) (H) mm(inch)
Displayed number of
16-dot standard font: 20 characters × 8 lines (two-byte characters)
D i s p l a y
characters
12-dot standard font: 26 characters × 10 lines (two-byte characters)
*1*2
section
Display color
Monochrome (black and white) 32 scales
B r i g h t n e s s
32 levels
Adjustment
Backlight
5 colors LED (white, green, pink, orange, red) (Not replaceable)
*3
Backlight life
Approx. 50000 h (operating ambient temperature: 25°C, display intensity: 50%)
Type
Analog resistive film
Key size
Minimum 2 × 2 dots (per a key)
To u c h
*4
panel
Simultaneous press
*5
Simultaneous press prohibited
(only 1 point can be pressed)
Life
1 million times or more (Operating force: 0.98 N or less)
U s e r
m e m o r y
Memory for storage (ROM): 3 MB
U s e r
capacity
memory
Life (number of write
capacity
100000 times
times)
RS-232 (rear face)
-
RS-232 (side face)
-
1 channel Transmission speed:
115200/57600/38400/19200/9600/
4800 bps
B u i l t - i n
Connector shape: terminal block 5-
pin
interface
RS-422/485
*6
Terminating resistor
: OPEN/110
Ω/330 Ω
(Switched with the terminating
resistor setting switch)
RS-422
-
1 channel Data transfer method:
10BASE-T/100BASE-TX
Ethernet
Connector shape: RJ-45 (modular
jack)
Specifications
*2
*2
Frequency
Acceleration
Half amplitude
5 to 8.4 Hz
-
3.5 mm
Under intermittent
vibration
8.4 to 150 Hz
2
9.8m/s
5 to 8.4 Hz
-
1.75 mm
Under continuous
vibration
8.4 to 150 Hz
2
4.9m/s
2
(15G) Three times in each X, Y, or Z direction
2
2
(stranded wire), or 0.25 to 0.5 mm
(rod terminal with an insulation sleeve).
*6
Specifications
GT2103-PMBDS
GT2103-PMBDS2
1 channel Transmission speed:
1 channel Transmission speed:
115200/57600/38400/19200/9600/
115200/57600/38400/19200/9600/
4800 bps
4800 bps
Connector shape: MINI-DIN6-pin
Connector shape: MINI-DIN6-pin
(female)
(female)
1 channel Transmission speed:
115200/57600/38400/19200/9600/
-
4800 bps
Connector shape: 9-pin terminal
block
1 channel Transmission speed:
115200/57600/38400/19200/9600/
4800 bps
Connector shape: terminal block 9-
pin
-
*6
Terminating resistor
: OPEN/110
Ω/330 Ω
(Switched with the terminating
resistor setting switch)
-
-
-
-
Item
USB (Device)
B u i l t - i n
interface
*7
SD card
Buzzer output
Productive structure
Sweep Count
External dimensions
10 times in each X,
Panel cut dimensions
Y, or Z direction
-
Weight (excluding a fitting)
Compatible software package
-
-
*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible to completely avoid this symptom, as
the liquid crystal display comprises of a great number of display elements. In addition, color tone difference, unevenness of brightness, or flickers may occur due to
individual differences of liquid crystal display panels. Please note that these symptoms occur due to GOT's characteristic and are not caused by product defect.
*2 Flicker may occur due to vibration, shock, or display color.
*3 Settings the screen saving backlight to OFF prevents the display screen from burn-in and enables the backlight to lengthen its life.
*4 When using a stylus pen, it will be 100,000 times. (The specifications must be satisfied the following condition.)
- Material: Polyacetal resin
- Tip radius: 0.8 mm or more
*5 If you touch two or more points on the touch panel simultaneously and a switch is placed between the two points, the switch may be activated. Do not touch two or more
points on the touch panel simultaneously.
*6 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.
2
*7 It is necessary to mount the separately sold SD card unit (GT21-03SDCD).
*8 Note that this does not guarantee all users' operation environment. In addition, the GOT may not be usable in the environment where oil or chemicals are splashed over
for a long time or where oil mist is filled.
*9 113 (W) × 74 (H) × 32 (D) mm when the SD card unit (GT21-03SDCD) is mounted
1.3 Power Supply Specifications
Item
Input power supply voltage
Under the
P o w e r
maximum load
consumption
At backlight off
Inrush current
P e r m i s s i b l e i n s t a n t a n e o u s
power failure time
GT2103-PMBLS
Noise immunity
Dielectric withstand voltage
Insulation resistance
Electrical wire size
Ferrules with plastic sleeve
Crimper type
Tight enin g torq ue (te rmin al
screws)
2. Wiring of connection cable
The diagram below shows cable assignment for GOT port.
Cable for GT2103-PMBD: GT21-CR4-8P5, GT21-CR4-25P5
Cable for GT2103-PMBDS: GT10-CR4-8P, GT10-CR4-25P
Cable for GT2103-PMBDS2: GT10-CR2-6P
Cable for GT2103-PMBLS: GT10-CR4-8P
GOT
PLC connection cable
-
GT21-C□□□R4-8P5
GT10-C□□□R4-8P
GOT
Untied
(terminal
wire
-
block)
color
24V
5V
SDA
Brown
SDB
Red
RDA
Orange
RDB
Yellow
SG
Green
-
RSA
Black
*1
*1
RSB
*1
White
*1
CSA
*1
CSB
*1
1 channel Transmission speed:
*1 The cable for GT2103-PMBD does not have connections to the signals (RSA, RSB, CSA,CSB).
115200/57600/38400/19200/9600/
User-made cable is necessary, depending on the PLC.
4800 bps
For the detail, refer to GOT2000 Series Connection Manual.
Connector shape: 9-pin terminal
block
Cable jacket to remove
Tightening torque
-
Recommended Tool (Screwdriver)
Specifications
GT2103-PMBD
GT2103-PMBDS
1 ch
Maximum transfer rate: Full-Speed 12 Mbps Connector shape: USB Mini-B
1 channel SDHC card supported (max. 32 GB)
Single tone (tone length adjustable)
*8
Outside the enclosure: IP67F
Inside the enclosure: IP2X
113(4.45) (W) × 74(2.92) (H) ×
113(4.45) (W) × 74(2.92) (H) × 27(1.07) (D) mm
32(1.26) (D) mm
105(4.14) (W) × 66(2.6) (H) mm
0.2 kg
GT Works3 Version1.112S or later
Specifications
GT2103-PMBD
GT2103-PMBDS
DC24 V (+10%, -15%)
2.6 W or less
1.9 W or less
2.0 W
1.3 W
30 A or less (1ms, 25°C, at the maximum load)
Within 5ms
Noise voltage: 1000 Vp-p, Noise width: 1 μs (by noise simulator of 30 to 100 Hz noise frequency)
500 VAC for 1 minute (between the GOT's power supply terminals and the GOT's grounding terminal)
10 MΩ or larger by insulation resistance tester
(between the GOT's power supply terminals and the GOT's grounding terminal)
No. of wire per terminal: 1
2
Solid wire 0.14 to 1.5 mm
AWG26 to AWG16, Stranded wire 0.14 to 1.0 mm
AWG24 to AWG20
No. of wire per terminal: 2
2
Solid wire 0.14 to 0.5 mm
AWG26 to AWG20, Stranded wire 0.14 to 0.2 mm
AI 0.25-6BU (AWG24), AI 0.34-6TQ (AWG22), AI 0.5-6WH (AWG20) (Phoenix Contact Inc.)
CRIMPFOXZA3 (Phoenix Contact Inc.)
0.22 to 0.25 N·m
This manual confers no industrial property rights or any rights of any other
kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation
cannot be held responsible for any problems involving industrial property rights
which may occur as a result of using the contents noted in this manual.
Warranty
PLC
Exclusion of loss in opportunity and secondary loss from warranty liability
Regardless of the gratis warranty term, Mitsubishi shall not be liable for
compensation to:
(1) Damages caused by any cause found not to be the responsibility of
Mitsubishi.
GT21-C□□□R4-25P5
(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi
GT10-C□□□R4-25P
GT10-C□□□R2-6P
products.
(3) Special damages and secondary damages whether foreseeable or not,
GOT
Untied
GOT
Untied
(terminal
(terminal
compensation for accidents, and compensation for damages to products
wire
wire
other than Mitsubishi products.
block)
block)
color
color
(4) Replacement by the user, maintenance of on-site equipment, start-up test run
24V
24V
and other tasks.
SDA
Brown
SD
Brown
SDB
Red
RD
Red
RDA
Orange
ER
Blue
RDB
Yellow
DR
Yellow
SG
Green
SG
Green
This product has been manufactured as a general-purpose part for general
RSA
*1
Blue
*1
RS
Purple
industries, and has not been designed or manufactured to be incorporated in
RSB
*1
Purple
*1
CS
a device or system used in purposes related to human life.
CSA
*1
Black
*1
NC
Before using the product for special purposes such as nuclear power, electric
White
CSB
*1
*1
NC
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
7 mm (0.27")
0.22 to 0.25 N·m
SZS 0.4 × 2.5 (Phoenix Contact Inc.)
HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
GT2103-PMBDS2
GT2103-PMBLS
-
113(4.45) (W) × 74(2.92) (H) ×
*9
27(1.07) (D) mm
0.18 kg
GT Works3 Version1.119Z or later
GT2103-PMBDS2
GT2103-PMBLS
5VDC (±5%), supplied from the
PLC
2.2 W or less
1.1 W or less
1.6 W
0.7 W
-
-
-
-
2
2
AWG26 to AWG16, Ferrules with plastic sleeve 0.25 to 0.5 mm
2
AWG26 to AWG24
For safe use

Advertisement

Table of Contents

   Also See for Mitsubishi Electric GT2103-PMBD

   Related Manuals for Mitsubishi Electric GT2103-PMBD

This manual is also suitable for:

Gt2103-pmbds2Gt2103-pmbdsGt2103-pmbls

Comments to this Manuals

Symbols: 0
Latest comments: