1. Manuals
  2. Brands
  3. Valor Manuals
  4. Indoor Fireplace
  5. StoneFire SFMK01
  6. Installation instructions manual

Valor StoneFire SFMK01 Installation Instructions Manual

Stonefire inner frame kit
Hide thumbs
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Download this manual
STONEFIRE INNER FRAME KIT
Valor Model 530 Heater and a StoneFire Mantel
Note: This kit must be installed or serviced by a qualified installer, service agency or gas supplier.
These instructions are to be used in conjunction with the main installation instructions for the above
listed model.
WARNING: If the information in these instructions is not followed exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
GENERAL
This kit consists of a set of black sheet metal panels used to extend the perimeter size of the engine to accommodate
StoneFire mantels, with the addition of an inner cast iron frame and selection of door options.
Kit components
REFER TO MAIN INSTALLATION BOOKLET SUPPLIED WITH THE ENGINE.
FOR MANTEL, FRONT, FRET AND DOORS INSTALLATIONS,
REFER TO INSTALLATION BOOKLET SUPPLIED WITH EACH KIT.
4001105/03
SFMK01

INSTALLATION INSTRUCTIONS

CSA approved for use only with
FOR ENGINE CONFIGURATIONS AND VENTING,
Installation diagram
(See price list for choice of Fronts, Frets and Door Kits.)
TM

Advertisement

Table of Contents
loading

Related Manuals for Valor StoneFire SFMK01

Summary of Contents for Valor StoneFire SFMK01

  • Page 1: Installation Instructions

    INSTALLATION INSTRUCTIONS CSA approved for use only with Valor Model 530 Heater and a StoneFire Mantel Note: This kit must be installed or serviced by a qualified installer, service agency or gas supplier. These instructions are to be used in conjunction with the main installation instructions for the above listed model.
  • Page 2 This kit is designed to use with the Stonefire mantels. SMTR StoneFire Traditional Mantel SMCL StoneFire Classic Mantel SMCO StoneFire Contemporary Mantel...
  • Page 3 FRAMING Note: These instructions are in addition to installation instructions supplied with Valor 530 firebox unit. Any combustible framing construction must be clear of standoffs. • A non-combustible hearth is not necessary in front of this appliance. • The 530 fireplace is approved to install directly on wood sub-flooring.
  • Page 4 FRAMING (cont.)

  • Page 5: Hearth Installation

    HEARTH INSTALLATION...

  • Page 6: Kit Assembly

    KIT ASSEMBLY Locate leg brackets to sides of engine and secure Locate and secure standoffs to rear corners of engine. with 4 #8 screws; locate and secure rear support. Place the insulation pad on top of the engine, cutting around the pipe if installing a top vent. Place engine into cavity and secure to framing.

  • Page 7: Replacement Parts

    REPLACEMENT PARTS LH Standoff Bracket 40010 RH Standoff Bracket 400103 Insulation Pad(s) 620B987 Back Support 400085 LH Leg 4000818AZ RH Leg 4000819AZ Shield 4000830AZ Duct Panel 400081AZ Top Cover 4000816AZ Designed and Manufactured for/by MILES INDUSTRIES LTD. 190 - 2255 Dollarton Hwy., North Vancouver, BC, CANADA V7H 3B1 Tel.

  • Page 8: Manuel D'installation

    GÉNÉRAL Ce kit contient un ensemble de panneaux de métal noir pour agrandir l’encadrement du foyer Valor modèle 530 afin de permettre l’installation d’un manteau de cheminée StoneFire. Contenu du kit Installation complète...
  • Page 9 Ce kit d’encadrement est conçu pour être utilisé avec les manteaux de cheminée Stonefire. SMTR Manteau de cheminée StoneFire Traditionel SMCL Manteau de cheminée StoneFire Classique SMCO Manteau de cheminée StoneFire Contemporain...
  • Page 10 ENCASTREMENT Note: Ces instructions sont en plus des instructions fournies avec le foyer Valor 530. • Une base de foyer non-combustible n’est pas nécessaire devant cet appareil • Le foyer 530 est homologué pour installation directement sur un sous-plancher de bois.
  • Page 11 ENCASTREMENT (suite)
  • Page 12 BASE DE FOYER...
  • Page 13 ASSEMBLAGE DE L’ENCADREMENT Placez les pattes de métal de chaque côté du foyer Placez et fixez les écarteurs aux coins arrières du et fixez-les avec 4 vis no. 8; placez et fixez le sup- foyer. port arrière au foyer. Placez le coussin isolant sur le dessus de la boite de foyer.

  • Page 14: Pièces De Remplacement

    PIÈCES DE REMPLACEMENT Écarteur gauche 40010 Écarteur droit 400103 Coussin isolant 620B987 Support arrière 400085 Patte gauche 4000818AZ Patte droite 4000819AZ Écran protecteur 4000830AZ Canalisation 400081AZ Panneau de couverture 4000816AZ Conçu et fabriqué pour/par MILES INDUSTRIES LTD. 190 - 2255 Dollarton Hwy., North Vancouver, C.-B., CANADA V7H 3B1 Tél.

Table of Contents