Programming Motorola Trunking System (800 Mhz); Programming Fleet Maps - Radio Shack PRO-2053 Owner's Manual

Follow these steps to program Motorola
trunking frequencies in the UHF-Lo band:
1. Press then
PROG
program mode.
2. Press and press (or hold)
FUNC
9 9 9 9
to select the bank.
3. Press and select
MODE
4. Press then
FUNC
cates
â8J<ý =I<Hôèý â8J<ý =I<Hôèý
â8J<ý =I<Hôèý â8J<ý =I<Hôèý
on the second line,
î î î î òìô òìô òìôòòòò òìô òòòò òòòò òòòò
on the third line and
the bottom line.
5. While in
â â â â â8J< â8J< â8J< â8J<
press the desired base frequency with
the number keys and press
Confirm the entry. If it is incorrect, press
the number keys again to set the base
frequency. After you confirm the input,
press again.
ENTER
Eý Eý Eý Eý E\\i[j E\\i[j E\\i[j E\\i[j
6. While in
enter the offset number and press
. Confirm the entry. If it is incor-
ENTER
rect, then press the number keys again
to set the frequency. After you confirm
the input, press
7. While in
/ / / / /K<G /K<G
/K<G /K<G
8 8 8 8 9 9 9 9
or to select the step number,
, or
ðíôò ðíôò íòôò íòôò
ðíôò ðíôò íòôò íòôò
.
ENTER
8. Press to enter the program mode.
PROG
9. Store the trunking IDs into the sub-bank
in the same bank.
to enter the ID
TRUNK
8 8 8 8
.
)+0 )+0 )+0 )+0
. The display indi-
2
on the first line,
E\\i[jý0ý).& E\\i[jý0ý).& E\\i[jý0ý).& E\\i[jý0ý).&
/K<Gý èý ðíôòB$Q /K<Gý èý ðíôòB$Q
/K<Gý èý ðíôòB$Q /K<Gý èý ðíôòB$Q
blinks, if necessary,
ENTER
blinks, if necessary,
again.
ENTER
blinks, repeatedly press
then press
ñðôíý B$Qõ ñðôíý B$Qõ
ñðôíý B$Qõ ñðôíý B$Qõ
Trunking Operation
Programming Motorola Trunking
System (800 MHz)
On the 800 MHz trunking band , you can se-
lect a base frequency (normal or offset).
or
On the 900 MHz trunking band , you do not
need to set the base/offset/step frequency.
Follow these steps to program 800 MHz
band Motorola trunking.
1. Press
PROG
program mode.
on
2. Press
FUNC
desired bank.
3. Press
MODE
.
ing mode.
4. Press
FUNC
8 8 8 8
5. Press
and press
J<K J<K J<K J<K
Notes :
• The default setting is
not receive with the
change to
• The base frequency in
851.0125 MHz. The base frequency in
+==J<K +==J<K
+==J<K +==J<K

Programming Fleet Maps

You must set the fleet map if you want to re-
ceive a Motorola Type I system. Fleet maps
are included along with other information
about Motorola
www.trunkscanner.com .
Follow these steps to program a fleet map.
1. Press
PROG
then to enter the ID
TRUNK
8 8 8 8 9 9 9 9
then or
and select Motorola trunk-
then .
3
9 9 9 9
or to select
*FID8C *FID8C
*FID8C *FID8C
.
ENTER
*FID8C *FID8C
*FID8C *FID8C
*FID8C *FID8C *FID8C *FID8C
.
+==J<K +==J<K
+==J<K +==J<K
is 851.0000 MHz.
Type I
then .
TRUNK
to select the
or -
+== +==
+== +==
. If you can
setting,
is
*FID8C *FID8C
*FID8C *FID8C
systems at
33