Transport And Storage - Ikra GM ARM 4038 Gartenmeister Operating Instructions Manual

Never spray the lawnmower with water or a pres-
-
sure washer and ensure that no water or other
fluids enter the housing.
NO T E!
Risk of damage!
Improper cleaning and maintenance can cause da-
mage.
Do not use any aggressive cleaning agents, bru-
-
shes with metal or nylon bristles, or any sharp or
metallic cleaning items such as knives, hard spa-
tulas, etc. You could damage the surfaces.
Remove the rechargeable battery before cleaning
-
the lawnmower.
Clean the housing and the grass discharge thorough-
-
ly after each use and allow all parts to dry properly.
Otherwise, damp grass residues may harden or start
to get mouldy and are then difficult to remove.
Remove all grass residues using a brush.
-
Clean all smooth surfaces with a damp cloth.
-
Treat all moving parts with environmentally friendly
-
oil.
Check the grass collection box regularly for wear or
-
loss of efficiency.
Regularly ensure that all nuts, bolts and screws are
-
firmly tightened and that the lawnmower is in a safe
working condition.
Replace parts that are worn out or damaged.
-
Replacing the cutting blade
NO T E!
Danger of injury!
Improper maintenance can cause injuries.
- When adjusting the lawnmower, ensure that your
fingers cannot be trapped between the moving
cutting blade and fixed parts.
- Always wear safety gloves when handling the cut-
ting blade.
- When maintaining the cutting blade, be aware that
it can still move even if the power source is swit-
ched off.
- Only replace the cutting blade with an original
spare part (see the "Spare parts" chapter)
Damaged and worn cutting blades must no longer be
used and must be replaced with manufacturer's original
spare parts. Regularly check whether the cutting blade is
blunt or damaged. Proceed as follows to replace:
1. Ensure that all rotating parts have come to a comple-
te standstill and that the lawnmower has cooled down
2. Remove the safety key (6) and remove the battery.
3. Turn the lawnmower onto its side.
4. Use a screwdriver to unscrew the fastening screw
and remove it together with the washer (see Fig. 7).
5. Remove the cutting blade (27).
6. Place a new cutting blade on the drive plate (24).
7. Place the washer and fastening screw back onto the
cutting blade and tighten them.
GB | Operating Instructions
- Before using again, ensure that the new cutting blade

Transport and storage

Transporting the lawnmower and the rechargeable
battery improperly can cause injuries and damage.
- When transporting the lawnmower by car, it must
- In order to prevent the battery discharging deeply,
- When transporting or storing the battery, mask
- Before transporting and storing, ensure that all parts
- If necessary, release the quick clamps and fold the
- Always store the lawnmower and the battery in a dry
- Protect the lawnmower and the battery from direct
- Keep the lawnmower and battery inaccessible to
- Private people are not subject to the hazardous goods
Sending devices with inserted or enclosed rechargeable
batteries, as well as sending individual rechargeable
batteries may only be carried out by trained staff from a
parcel service, a courier or a haulage firm.
GB-9
is attached correctly and is tight.
WARNIN G!
Risk of injury and damage!
be positioned so that it poses no danger, and se-
cured.
charge it completely before an extended storage
period.
the contacts or pack the battery in a plastic bag
or box.
are completely dry.
guide bar (1) and the guide bar frame (11) together
carefully.
place.
sunlight.
children, safely locked away and at a storage tempe-
rature between +10 °C and +40 °C.
ordinance when transporting the rechargeable bat-
teries if the load is transported safely, the goods are
packaged for retail sale and are intended for personal
or home use.