Related Manuals for BK Precision 9130B
Summary of Contents for BK Precision 9130B
- Page 1 9130B Series Triple Output Programmable DC Power Supplies Models: 9130B, 9131B, 9132B USER MANUAL GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 2: Safety Summary
Category IV (CAT IV): Measurement instruments whose measurement inputs are meant to be connected to the primary power entering a building or other outdoor wiring. Do not use this instrument in an electrical environment with a higher category rating than what GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 3 • In the presence of noxious, corrosive, or flammable fumes, gases, vapors, chemicals, or finely-divided particulates. • In relative humidity conditions outside the instrument's specifications. • In environments where there is a danger of any liquid being spilled on the instrument or GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
- Page 4 Under certain conditions, even with the power cord removed, dangerous voltages may exist GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
- Page 5 Do not continue to operate the instrument if you cannot verify the fan is operating (note some fans may have intermittent duty cycles). Do not insert any object into the fan's inlet or outlet. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
- Page 6 • Do not pull the instrument with the power cord, connected probe, or connected test lead. • Do not move the instrument when a probe is connected to a circuit being tested GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 7: Compliance Statements
Directive, is marked as being put on the market after August 13, 2005, and should not be disposed of as unsorted municipal waste. Please utilize your local WEEE collection facilities in the disposition of this product and otherwise observe all applicable requirements. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 8: Ce Declaration Of Conformity
Low Voltage Directive EN61010-1: 2001 EMC Directive EN 61000-3-2: 2006 EN 61000-3-3: 1995+A1: 2001+A2: 2005 EN 61000-4-2 / -3 / -4 / -5 / -6 / -11 EN 61326-1: 2006 viii GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 9: Safety Symbols
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 10: Table Of Contents
Over Voltage Protection (OVP) ..................18 Save/Recall Instrument Settings ..................18 Key Lock .......................... 19 Output Check ........................19 Menu Access and Options ................21 How to Access the Menu....................21 Menu Options ......................... 21 GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 11 Remote Operation ..................32 Interface Configuration ....................32 Remote Commands ..................34 Troubleshooting Guide ................35 Specifications ..................... 36 Calibration ....................37 SERVICE INFORMATION ................38 LIMITED THREE-YEAR WARRANTY ............38 GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 12: General Information
1 General Information 1.1 Product Overview The 9130B Series programmable triple output DC power supplies feature isolated outputs that can be adjusted independently. They can be configured for series or parallel mode when connecting multiple channels together. The front panel keys and the rotary knob provide a convenient means for setting values and adjusting parameters. -
Page 13: Product Dimensions
1.3 Product Dimensions The 9130B power supply’s dimensions are approximately 214.5 mm (8.44 in) x 88.2 mm (3.47 in) x 354.6 mm (13.96 in) (W x H x D). The 9131B and 9232B power supply’s dimensions are approximately 214.5 mm (8.44 in) x 88.2 mm (3.47 in) x 445 mm (17.52 in) (W x H x D). -
Page 14: Rackmount Installation
The instrument can be installed in a standard 19-inch rack using the optional IT-E151 rackmount kit. Below is an image of a 9130B Series model installed with the IT-E151 rackmount kit. Note: Remove the carrying handle and the two plastic ears before mounting the instrument. To remove the handle, grasp the handle by its sides, pull outwards, and rotate it until the arrow on the handle and the arrow on the plastic ears are in opposite directions. - Page 15 To rackmount a single instrument, order rackmount kit IT-E151 To rackmount two instruments side-by-side, order rackmount kit IT-E151 and remove the front panel cover GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 16: Front Panel Overview
1.5 Front Panel Overview Figure 1 - Front Panel Front Panel Description VFD display Shift key Local key Power key Numeric keys Function keys Cursor keys Output terminals Rotary knob GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 17: Rear Panel Overview
1.6 Rear Panel Overview Figure 2 - Rear Panel Rear Panel Description Cooling fan Remote sense terminal AC power input receptacle & fuse box RS-232 interface USB interface GPIB interface GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 18: Keypad Overview
Adjusts cursor position or select menu items. Up/Down arrow keys Used to select menu items or increase/decrease output voltage or current values. Esc key Cancel and return to previous menu. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 19: Display Overview
Indicates output is off Indicates constant voltage mode Indicates constant current mode Indicates the shift button is pressed Tracking mode enabled Indicates remote mode Keyboard lock enabled Indicates the channel currently selected GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 20: Getting Started
SHOCK HAZARD: The power cord provides a chassis ground through a third conductor. Verify that your power outlet is of the three-conductor type with the correct pin connected to earth ground. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 21: Fuse Requirements
Check and replace fuse (if necessary) for the desired line voltage operation (see Table 1 - Fuse Table). Fuse box slit Fuse box Check/Remove Fuse Figure 5 - Fuse replacement GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 22 Any disassembling of the case or changing the fuse not performed by an authorized service technician will void the warranty of the instrument. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 23: Output Connections
Ensure that the load wiring insulation rating is greater than to the maximum output voltage of the power supply. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 24: Carrying Handle Adjustment
Handle transport position Figure 7 - Carrying Handle Be sure the handle is locked in position and avoid twisting movements while transporting as the handle can damage and drop the power supply. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 25: Preliminary Check
After the Scan System is complete the VFD will display as shown in Figure 9. Figure 9 - Scan Complete Note: The initial power on state is based on the settings in the (Config) configuration menu. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 26 Cal Lost Calibration data within the EEPROM is lost. Fact Loss Factory calibration data is lost. Model Lost Channel initialization failed. If any of these errors occur, please contact B&K Precision. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 27: Front Panel Operation
3 channels of the power supply. To control the output state of each channel individually, press , or channels 1, 2, or 3 respectively. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 28: Meter Mode
When output is ON, the user can use the rotary knob to adjust the voltage value when the output is in constant voltage mode. The same can be done to adjust the current value when output is in constant current mode. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 29: Over Voltage Protection (Ovp)
Recall Settings 1. Press button to enter Recall mode. The button will be illuminated. 2. Use the numeric keypad to enter the memory location between 1 through 9 to recall GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 30: Key Lock
Note: The button will automatically return to meter mode and illuminate after 5 seconds of a valid entry (see 4.10 Return Meter to disable this). GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 31 7. Verify channels 2 and 3 according to steps 1 through 6. 8. Press the power switch to turn off the power supply and remove the short on the output terminals. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 32: Menu Access And Options
Select and configure RS232, GPIB, and USB interfaces MemoryGroup Select memory group Protocol Select SCPI options ReturnMeter Enable automatic return state Reset Reset menu Exit Move up menu structure System Configure channel 1 GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 33: Output Power-On State
1. From the Config menu, select Knob and press the button. 2. There are two options that can be selected by using the keys or rotary knob: Unlock – Enable rotary knob GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 34: Buzzer On/Off
1. From the Config menu, select USB and press the button. This will select the USB interface for remote communication. 2. To exit the menu at any time, press the key twice. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 35: Memory Group
This option allows users to enable an internal fixed timer delay (5 seconds) for the power supply to automatically switch from settings mode to meter mode. When enabled, it will automatically switch to meter mode after 5 seconds. The backlight of the button will GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 36: System Menu
DUT (Device under test) connected to the power supply. The maximum voltage can be entered using the numeric keypad, rotary knob or the Up/Down arrow keys. OutTimer GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 37: Combined Series And Parallel Modes
1 and 2. The following steps will describe the external wiring and instrument setup required to use this feature. 1. Power down the unit and remove all wiring from the output terminals. 2. Verify all wiring is connected as illustrated below: GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 38 1 and 2, 2 and 3, or All. The following steps will describe the external wiring and menu options for combining channels CH1+CH2. 1. Power down the unit and remove all wiring from the output terminals. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
- Page 39 Parallel ALL Mode The following steps will describe the external wiring and menu options for combining ALL channels. 1. Power down the unit and remove all wiring from the output terminals. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 40: Tracking Mode
2. Select one of the following: CH1+CH2, CH1+CH3 or ALL. Then, press the button. The power supply will display Track Set Successful! The symbol will appear on the display to indicate tracking is enabled. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 41: Parameters In Series/Parallel Mode
The power supply is initially set up to local sense mode by default. Refer to the following sections for details of local and remote sense setup. Local Sense By default, the power supply is set up for local sense with jumpers installed. This is determined GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 42 1. Connect wires to the DUT as illustrated in Figure 20. Make the connections between + and S+ and S- and – for each channel that will be using remote sense. The S+ and S- wires should be twisted as illustrated to minimize noise. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 43: Remote Operation
5.1 Interface Configuration RS-232 For RS-232 connectivity, refer to the diagram below for pin out information. The RS-232 is labeled in the rear panel and it is a female DB-9 interface. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 44 Therefore, adding a delay between commands to allow for sufficient time to process commands is required. 5. All serial settings must match the settings configured on the PC in order for GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
-
Page 45: Remote Commands
USBTMC, RS-232, and GPIB. Refer to the programming manual for details, which can be downloaded from www.bkprecision.com. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 46: Troubleshooting Guide
For RS-232, check that the baud rate, parity, data bits, stop bit, and flow control settings match with the settings configured on both the software interface and the power supply GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 47: Specifications
1 mA Readback Resolution Voltage 1 mV 1 mV 1 mV Current 1 mA 1 mA 1 mA Programming Accuracy ± (% output + offset) Voltage ≤ 0.03% + 10 mV GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 48: Calibration
To ensure the most current version of this manual, please visit www.bkprecision.com. 9 Calibration We recommend a calibration interval of once per year to ensure that the power supply meets specifications. GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... -
Page 49: Service Information
This warranty gives you specific rights and you may have other rights, which vary from state-to-state. B&K Precision Corp. 22820 Savi Ranch Parkway Yorba Linda, CA 92887 www.bkprecision.com 714-921-9095 GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com... - Page 50 22820 Savi Ranch Parkway Yorba Linda, CA 92887 www.bkprecision.com © 2015 B&K Precision Corp. Printed in China v050615 GlobalTestSupply www. .com Quality BK Precision Products Online at: sales@GlobalTestSupply.com...
Need help?
Do you have a question about the 9130B and is the answer not in the manual?
Questions and answers